• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2000년도 종합학술발표회 논문집 Vol.10 No.1
• /
• pp.345-349
• /
• 2000

A microstrip polarized 8${\times}$2 linear phased array antenna with four 4-bit phase shifters is designed at 10 GHz. The 180$^{\circ}$and 90$^{\circ}$ sections of the phase shifter are of the switched line type, and the rests are of the loaded line type. A 2${\times}$2 sequential sub-array is adopted for a broad axial ratio bandwidth. The construction of the array antenna is of the tile type placing the phase shifters on the same layer containing the feed network. The element spacing is chosen to be 0.45λ$\sub$0/ to exclude the grating lobe. Measurement results show a gain 9.69 dB at broadside and 8.3 dB at the beam-tilt angle of 16$^{\circ}$ by imposing a progressive phase of 90$^{\circ}$.

• 한국생산제조학회지
• /
• 제5권1호
• /
• pp.33-42
• /
• 1996

The high coherence of laser beam has made it possible to observe interference effects even in the light scattered from rough surfaces. That's why, when object with a scattering surface is illuminated with laser light, we do see a speckled appearance due to random interference. This sort of unique property of laser speckle has bruht into existence the new noncontaciting techniques such as speckle metrology method of measuring deformation, displacement, and vibration etc of objects with high optical sensitivity. The measurable range of speckle metrology especially used to measure in -plane information, however, is limited by some factors, the so-called strain, rotation tilt of surface and out of displacement perpendicular to the plane of analysis This restrictions severly limits the measurable range of speckle metrology by causing the decorrelation of speckle patterns. It is the purpose of this paper to give a survey on the measurable limitation of speckle photography method that is one of speckle metrology. Namely we will discuss the mutual relationships and problems of each limitations adding the restriction on the largest and smallest displacement measurable with speckle methods.

• 한국해양공학회지
• /
• 제15권2호
• /
• pp.141-147
• /
• 2001

The launching process is one of the most critical operations for large structure in offshore installation. Since as the size increases it limits the availability of offshore crane facilities, the large jacket structures are often installed by launching. As the structure approaches to tilt beam, it reaches critical load, and there are parameters to affect on launching procedure. The major influential parameters are trim, draft of barge, center of gravity, center of buoyancy and reserved buoyancy of jacket. As increasing of trim and draft, structural loads tend to decrease. The trim is found to be more contributing than draft on structural loads. Therefore the trim should be increased so as to decrease structural loads and to avoid stalling of structure and submergence of stern. During the launching process, the distance between jacket and seabed should be investigated which differs from the amount of reserved buoyancy and launching condition of barge. In this paper the effects of parameters on launching process are numerically investigated.

• 한국전기전자재료학회논문지
• /
• 제24권8호
• /
• pp.647-653
• /
• 2011

In this study, a method to measure the thickness of thin film by EDS (energy dispersive spectroscopy) is suggested. We have developed a model which calculates the thickness of thin film from the characteristic x-ray intensity ratio of the elements in thin film and substrate by considering incident electron beam energy, x-ray generation curve, backscattering and absorption of x-ray, take-off angle of x-ray and tilt angle of the sample. We obtained the relation curve between the film thickness measured experimentally and the x-ray intensity ratio of elements. The film thicknesses calculated from the model agrees quite well with those measured experimentally. Therefore, the thin film thickness can be measured rapidly and accurately by using the model developed in this study and the x-ray intensity ratio obtained in EDS analysis.

• 제어로봇시스템학회논문지
• /
• 제5권5호
• /
• pp.568-576
• /
• 1999

Using a laser sheet beam projector combined with a CCD-Camera, an efficient technique to recognize complex surface of curvature and lane has been demonstrated for the purpose of mobile robot navigation. In general, obstacles of indoor environments in the field of SLIT-RAY plane are captured as segments of an elliptical arc and a line in the camera image. The robot has been capable of moving along around the obstacle in front of it, by recognizing the original shape of each segment with the differential coefficient by means of least squares method. In this technique, the imaged pixels of each segment, particularly elliptical arc, have been converted into a corresponding circular arc in the real-world coordinates so as to make more feasible the image processing for the position and radius measurement than conventional way based on direct elliptical are analyses. Advantages over direct elliptical cases include 1) higher measurement accuracy and shorter processing time because the circular arc process can reduce the shape-specifying parameters, 2) no complicated factor such as the tilt of elliptical arc axis in the image plane, which produces the capability to find column position and radiua regardless of the camera location . These are essentially required for a mobile robot application. This technique yields an accuracy less than 2cm for a 28.5cm radius column located in the range of 70-250cm distance from the robot. The accuracy obtained in this study is sufficient enough to navigate a cleaning robot which operates in indoor environments.

• 한국재료학회지
• /
• 제24권5호
• /
• pp.266-270
• /
• 2014

Aluminum nitride(AlN) films were grown on the C-face and on the Si-face of (0001) silicon carbide(SiC) substrates using plasma-assisted molecular-beam epitaxy(PA-MBE). This study was focused on first-stage growth manipulation prior to the start of AlN growth. Al pre-exposure, N-plasma pre-exposure, and simultaneous exposure(Al and N-plasma) procedures were used in the investigation. In addition, substrate polarity and, first-stage growth manipulation strongly affected the growth and properties of the AlN films. Al pre-exposure on the C-face and on the Si-face of SiC substrates prior to initiation of the AlN growth resulted in the formation of hexagonal hillocks on the surface. However, crack formation was observed on the C-face of SiC substrates without Al pre-exposure. X-ray rocking-curve measurements revealed that the AlN epilayers grown on the Si-face of the SiC showed relatively lower tilt and twist mosaic than did the epilayers grown on the C-face of the SiC. The results from the investigations reported in this paper indicate that the growth conditions on the Si-face of the SiC without Al pre-exposure was highly preferred to obtain the overall high-quality AlN epilayers formed using PA-MBE.

• 수산해양기술연구
• /
• 제35권3호
• /
• pp.301-311
• /
• 1999

The investigation to evaluate the possible effects of fish behaviour on acoustic target strength was carried out during the 1997 and 1998 hydroacoustic-demersal trawl surveys in the southern waters of Korea.The swimming speed and the target strength of individual, acoustically resolved fished swimming through the sound beam were measured using the split-beam tracking method on board R/V Kaya.The results obtained can be summarized as follows:1. The alongship and athwartship angles between -3dB poionts of a hull mounted 38 kHz split beam tranducer used in these surveys was >$3.76^{\circ}\;and\;6.74^{\circ}$ respectively, and the equal energy contour obtained from the measured beam pattern showed approximately the circular pattern. 2. The swimming speed measured off the south coast of Sorido in 23 January 1997 ranged 0.10 to 0.80 m/s with the average swimming spped of 0.36 m/s, and the target strength ranged -64.8 to -31.7 dB with the average target strength of -52.7 dB. The most dominant species sampled in this survey area were Japanese scaled sardine, Sardinella zunasi and Konoshiro gizzard shad, Konosirus punctatus, respectively.3. The swimming speed measured off the east coast of Kojedo in 24 March 1997 ranged 0.10 to 1.10 m/s with the average swimming speed of 0.40 m/s, and the target strength ranged -64.8 to -51.5 dB with the average target strength of -59.2 dB. The most dominant species sampled in this survey area were Swordtip squid, Photololigo edulis, Konoshiro gizzard shad and Japanese flying squid, Toddarodes pacificus, respectively and the swimming activity of these species seems to be controlled at speeds between 0.20 and 0.60 m/s. 4. The swimming speed measured the south coast of Kojedo in 25 March 1997 ranged 0.10 to 1.40 m/s with the average swimming speed of 0.51 m/s and the target strength ranged -64.3 to -47.7 dB with the average target strength of -55.1 dB. The most dominant species sampled in this survey area were Swordtip squid, Blotchy sillage, Sillago maculata and japanese scaled sardine, respectively and the swimming activity of these species seems to be controlled at speeds between 0.20 and 0.70 m/s.5. The swimming speed measured during morning twilight in the southeastern water of Cheju Island in 11 July 1998 ranged 0.20 to 1.0 m/s with the average swimming speed of 0.53 m/s, and the target strength ranged -65.0 to -47.0 dB with the average target strength of -57.1 dB. The most dominant species sampled in this survey area were Swordtip squid, Black scraper, Thamnaconus modesutus and japanese flying squid, respectively and the tile angle ranged$ +28^{\circ}\;to\;+2^{\circ}$ with the average tilt angle of -8.1$^{\circ}$ showing the downward migration.

• 대한전자공학회논문지TC
• /
• 제39권3호
• /
• pp.140-149
• /
• 2002

본 논문에서는 DBS 수신용 이동체 탑재형 시스템에 이용하기 위한 빔 틸트형 슬롯 어레이 복사 도파관 안테나의 특성을 기술하고 있다. 슬롯 도파관 어레이의 기초연구로써, 도파관 광벽면 위에 놓인 16 슬롯 소자에 대하여 설계를 행하였다. 빔 틸트 특성을 가지는 안테나의 슬롯 길이, 슬롯사이의 거리 그리고 크로스 슬롯의 사이각과 같은 설계 파라미터들은 모멘트법에 의해 계산되었다. 이들 결과를 근거로 16소자x16열의 복사 도파관 안테나를 설계·제작하였다. 제작된 안테나의 측정된 주 빔의 지향각은 48°∼50° 사이로 다소 측정 주파수에 의존했으며, 측정치는 설계치와 잘 일치하였다. 측정된 앙각 지향성의 3 dB 빔폭은 약 13° 정도였고, DBS 대역에서의 축비는 약 2.8 dB 이하, 이득은 24 dBi 이상으로 관측되었다. 제작한 도파관 평면 안테나의 성능을 평가하기 위하여, 안테나를 위성 추적 제어시스템과 결합하여 차량을 이용하여 고속도로에서 필드 성능 시험을 행하였다. 측정을 하는 동안, 차안에서 연속적인 TV 시청이 가능하였고 제안된 안테나의 우수한 성능이 입증되었다

• 한국전산구조공학회논문집
• /
• 제30권1호
• /
• pp.31-37
• /
• 2017

본 논문에서는 이종재질로 구성된 세장비가 큰 보의 차원축소와 복원의 효율성과 정확성을 입증하기 위하여 VABS와 3차원 유한요소해석 모델의 결과와 비교하였다. 그리고 3차원 유한요소모델과 차원축소 모델을 가상균열닫힘법을 이용하여 에너지 해방률을 계산하였다. 원형과 사각형의 단면에 초기 크랙을 가진 수치모델을 이용하여 보의 차원축소와 복원기법 및 가상균열닫힘법을 이용하여 복원해석 결과 및 에너지 해방률을 비교하여 효율성과 정확성을 입증하였다. 특히 제시된 에너지 해방률 계산 기법은 고고도 무인기의 날개, 헬리콥터 로터 블레이드, 풍력 블레이드, 틸트로터 등의 정적, 동적 모델링 및 수명평가에 활용될 수 있을 것이다.

• 수산해양기술연구
• /
• 제46권3호
• /
• pp.239-247
• /
• 2010

Species of fish such as striped beakperch, bluefin searobin and konoshiro gizzard shad are commercially very important due to their high demand in the Korean market. When estimating acoustically the abundance of stocks for these species, it is of crucial importance to know the target strength (TS) to the length dependence. In relation to these needs, the TS experiments were conducted on three different species in an acrylic salt water tank using two split-beam echo sounders of 70 and 120 kHz. The TS for these three species under the controlled condition was simultaneously measured with the swimming movement by a DVR system and analyzed as a function of fish length (L) and frequency (or wavelength $\lambda$). The equation of the form TS=a log (L)+b log ($\lambda$)+c was derived for their TS-length dependence. The best fit regression of TS on fork length for striped beakperch was estimated as TS=35.67 log (L, m) -15.67 log ($\lambda$, m) -46.69 ($r^2$=0.78). Furthermore, the best fit regression of TS on fork length for konoshiro gizzard shad was shown to be TS=25.85 log (L, m) -5.85 log ($\lambda$, m) -32.22 ($r^2$=0.51). The averaged TS for 12 bluefin searobins with a mean length of 24.36cm at 70 kHz was analyzed to be -41.55dB. In addition, the averaged tilt angle obtained simultaneously by a DVR system with TS measurements for 27 konoshiro gizzard shads swimming within an acrylic salt water tank was estimated at $-2.7^{\circ}$.