• 한국대기환경학회지
• /
• 제27권6호
• /
• pp.672-680
• /
• 2011

Three new granular absorbents were prepared from calcium hydroxide, and applied to an FGD process with internal circulation. The aim of the study was finding the most efficient of the these three applied absorbents for the $SO_2$ removal at high flue gas temperatures. The absorbent is fed to the testing unit at high operation temperature and fluidized inside the FGD system where the sorbent particles react with the $SO_2$ gas. The rate of $SO_2$ decomposition was high in C-type absorbent which had the large surface area. De-SOx characteristics of the current absorbents appeared to be similar to the other conventional agents in this fluidized bed combustor. In particular, the optimum de-SOx condition could be achieved at high mole ratios of Ca to S which can reduce the residual $SO_2$.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.17-18
• /
• 2006

Laser welding of metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research works is to investigate the influence of the process parameters, such as the welding for metals with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the butt welding, the welding quality of the cut section, stain-stress behavior and the hardness of the welded part are investigated. From the results of the investigation, it has been shown that the optimal welding condition without defects in the vicinity of the welded area and with a good welding quality is 1400W of the laser power, 0.8m/min, 0.9m/min of welding speed and $4{\ell}$ in of pressure for shielding gas.

• 한국생산제조학회지
• /
• 제25권5호
• /
• pp.329-337
• /
• 2016

The demand for the eco-friendly vehicles is skyrocketing because of the increasing $CO_2$ emissions and global warming. In the industrial field, the battery process, a core part of an eco-friendly vehicle, is drawing increased attention; its weight lightening as well as high energy density are becoming increasingly important. In this study, pure Ni plates that were used as the battery pole plate were welded using the laser. The lab joint welding was conducted on ten pure Ni plates at a laser power of 1900 W and a feed speed of 2.8-3.4 m/min. As observed in the experiment, a faster feed speed reduced the bead width, but the laser did not penetrate all ten specimen plates. In addition, pores were trapped when protective gas was used, but they were not trapped when the welding was conducted in atmospheric condition.

• Journal of Welding and Joining
• /
• 제26권6호
• /
• pp.67-73
• /
• 2008

Three-dimensional transient simulation of laser-GMA hybrid welding involving multiple physical phenomena is conducted neglecting the interaction effect of laser and arc heat sources. To reproduce the bubble and pore formations in welding process, a new bubble model is suggested and added to the established laser and arc welding models comprehending VOF, Gaussian laser and arc heat source, recoil pressure, arc pressure, electromagnetic force, surface tension, multiple reflection and Fresnel reflection models. Based on the models mentioned above, simulations of laser-GMA hybrid butt welding are carried out and besides the molten pool flow, top and back bead formations could be observed. In addition, the laser induced keyhole formation and bubble generation duo to keyhole collapse are investigated. The bubbles are ejected from the molten pool through its top and bottom regions. However, some of those are entrapped by solid-liquid interface and remained as pores. Those bubbles and pores are intensively generated when the absorption of laser power is largely reduced and consequently the full penetration changes to the partial penetration.

• 한국분말재료학회지
• /
• 제19권4호
• /
• pp.310-316
• /
• 2012

Nanocrystalline $BaTiO_3$ powder could be synthesized by solid-state reaction using the mixture which was prepared by a high energy milling process in a bead mill for $BaCO_3$ and nanocrystalline $TiO_2$ powders mixture. Effect of the milling time on the powder characteristic of the synthesized $BaTiO_3$ powder was investigated. Nanocrystalline $BaTiO_3$ with a particle size of 50 nm was obtained at $800^{\circ}C$. High tetragonal $BaTiO_3$ powder with a tetragonality(=c/a) of 1.009 and a specific surface area of $7.6m^2/g$ was acquired after heat-treatment at $950^{\circ}C$ for 2 h. High energy ball milling was effective in decreasing the reaction temperature and increasing the tetragonality.

• 한국레이저가공학회지
• /
• 제11권4호
• /
• pp.21-28
• /
• 2008

Remote Laser welding technology for manufacturing automotive body is studied. Laser welding and industrial robot systems are used for the robot based laser welding system. The laser system is used 1.6kW Fiber laser(YLR-1600) of IPG. The robot system is used HX130-02 of Hyundai Heavy Industry(payload : 130kg). The robot based laser welding system is equipped with laser scanner system for remote laser welding. The welding joints of steel plate and steel plate coated with zinc are butt and lapped joints. The quality test of the laser welding are through the observation the shape of bead on plate and cross-section of welding part. During past three years the laser system, 4kW Nd:YAG laser (HL4006D) of Trumpf was used and the robot system, IRB6400R of ABB (payload:120kg) was used. The new laser source, robot and laser scanner system are used to increase the processing speed and to improve the process efficiency. This paper introduces the robot based remote laser welding system to resolve the limited welding speed and accuracy of the conventional laser welding system.

• 한국자동차공학회논문집
• /
• 제16권5호
• /
• pp.60-67
• /
• 2008

The catalytic filter of Cu-ZSM5/alumina beads was considered to reduce NOx in the urea SCR system. Catalytic support of porous alumina beads with mean pore size $130{\mu}m$ and porosity $75{\sim}83%$ were prepared using foaming and gel-casting method. The Cu-ZSM5 catalysts were coated on the supporting alumina beads using $Cu(NO_3)_2$ by ion exchange method. After a washcoating process was applied to coat 10w% Cu-ZSM5 on porous alumina bead, coating layer was estimated $20{\mu}m$ in thickness. The characterization and the feasibility as a catalytic supports were investigated. And the NOx conversion test in Cu-ZSM5/Alumina Beads filter system was conducted by using Urea as reductants under laboratory test. The NOx conversion was increased as size and porosity of beads and observed more than 95% excellent NOx conversion above $300^{\circ}C$.

• 대한가정학회지
• /
• 제50권5호
• /
• pp.39-49
• /
• 2012

This study looked into the trend of expression of animal motifs that appears in modern fashion, and the values embedded in them. As to the research method, empirical analysis was performed on the works presented at the four global collections of Paris, Milan, New York and London from 2001S/S to 2010F/W, as well as a literature review. As a result, animal motifs applied in modern fashion appeared in material groups, such as leather or feather. The first group shows a realistic material feel, with artificial leather or fur, expressed in a transformed complex animal motif, with process skill or various methods of expression. The second group is the case of a single motif or reality, mode, and ion pattern. Printing is a generic expression, but patchwork, collage or bead ornament are also used, and expressed in the various forms of pattern: pattern in a single animal, pattern in different animals, and pattern combining both animal and other shape. The third group is a small decorative ornament, including headset or accessory and makeup, which is transformed in an animal-characterized motif into part of clothing components for expression, or to set the real animal to the stage for a performance. The embedded values were also categorized as natural beauty, sensual female beauty, pleasure, and ornamentation, which could be an endless spiritual source, and a breakthrough that enables us to show a creative and new aesthetic for the modern fashion field.

• 한국레이저가공학회:학술대회논문집
• /
• 한국레이저가공학회 2006년도 추계학술발표대회 논문집
• /
• pp.17-20
• /
• 2006

In the remote welding system using $CO_2$ laser, laser beam is rapidly deflected by moving mirrors of scanner system and has focusable distance over 1000mm from workpiece. From such arrangement, various advantages and disadvantages arise. Remote welding is a highly efficient laser process. As the mirrors of the scanner system allow positioning speeds exceeding 700m/s, it becomes possible to reduce the welding cycle time. On the other hand, as there no the provision of shielding gas which is normally required for beam powers exceeding 3kW, may become difficult task. Therefore, In this study, the influence of the various penetration of back bead by the different laser welding speed on the weld seam formation without shielding gas was investigated.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2008년도 특별논문집
• /
• pp.90-95
• /
• 2008

The letters and marks on the hull of vessels are marked by welding bead or steel plate to resist the corrosion environment. It has done by manual work. So, it cause deterioration of welding quality and process delay and so on. The automated welding device for draft mark has developed partially in the field of shipbuilding. But it can be used for draft mark only. And it has caused a few problems about that workablity and movablity are decreased owing to the size and weight of device. So we developed the automated welding device that can be used for most letters and marks on the hull. It designed to 3 axises mobile robot include to ratoation axis and stand alone type controller with multi GUI base on imbedded windows.