• Journal of Information Processing Systems
• /
• v.2 no.1
• /
• pp.39-43
• /
• 2006

In this paper, we proposed TASL-MAC, a medium-access control (MAC) protocol for wireless sensor networks. In wireless sensor networks, sensor nodes are usually deployed in a special environment, are assigned with long-term work, and are supported by a limited battery. As such, reducing the energy consumption becomes the primary concern with regard to wireless sensor networks. At the same time, reducing the latency in multi-hop data transmission is also very important. In the existing research, sensor nodes are expected to be switched to the sleep mode in order to reduce energy consumption. However, the existing proposals tended to assign the sensors with a fixed Sleep/Listening schedule, which causes unnecessary idle listening problems and conspicuous transmission latency due to the diversity of the traffic-load in the network. TASL-MAC is designed to dynamically adjust the duty listening time based on traffic load. This protocol enables the node with a proper data transfer rate to satisfy the application's requirements. Meanwhile, it can lead to much greater power efficiency by prolonging the nodes' sleeping time when the traffic. We evaluate our implementation of TASL-MAC in NS-2. The evaluation result indicates that our proposal could explicitly reduce packet delivery latency, and that it could also significantly prolong the lifetime of the entire network when traffic is low.

• Journal of Astronomy and Space Sciences
• /
• v.15 no.2
• /
• pp.459-473
• /
• 1998

As the satellite system becomes more complex, the probability of unpredictable failures may be increased due to design inadequacy, experience deficiency, lack of problem recognition. Poor quality control, improper testing, and workmanship fault. Consequently, these problems can lead to the reduction or end of the satellite mission lifetime. This article addresses general satellite failure modes and factors influencing satellite mission life. The mission life factors of LEO sun-synchronous KOMPSAT spacecraft are investigated, in which its mission life is predicted based on these factors. Since the end of mission due to random failures is not predictable, the predictable mission life factors such as power budget, propellant budget, battery charging/discharging cycle, radiation effects payload reliability, single point failure, and redundancy are primarily investigated.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.5
• /
• pp.955-961
• /
• 2009

Present, a portable battery have problem that the volume increases according to capacity Increase. Direct Methanol Fuel Cell is alternative by solution plan of this problem. In this paper, the characteristics of DMFC are analyzed by change in concentration and discharge of fuel in natural convection and room temperature condition. According to the analysis result, polarization by delay of diffusion velocity of hydrogen ion appeared in methanol of low concentration. And if have a lot of supplies of methanol, generation power declines by electric cell cooling effect.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.11
• /
• pp.2441-2446
• /
• 2009

Wireless Sensor Network collects a data from the specific area and the control is composed of small sensor nodes. Like this sensors to after that is established at the beginning are operated with the battery, the operational duration until several years must be continued from several months and will be able to apply the resources which is restricted in efficiently there must be. In this paper RHC (rounting history cache) applies in Directed Diffusion which apply a data central concept a reliability and an efficiency in data transfer course set. RHC algorithms which proposes each sensor node updated RHC of oneself with periodic and because storing the optimization course the course and, every event occurrence hour they reset the energy is wasted the fact that a reliability with minimization of duplication message improved.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.992-996
• /
• 2004

Small electric motors in an automobile perform various tasks such as engine cooling, pumping, and in heating, ventilating, and air-conditioning (HVAC) system. At present, most of dc motors are supplied by 12V or 24V batteries. However, DC motors surfer from lack of efficiency, low life cycles and unreliability. Therefore, there is a growing interest in substituting DC motors for advanced AC motors including switched reluctance motors. Although there are several other forms SRM converters, they are either unsatisfactory to the control performance or unsuitable for the 12V-battery powered 3-phase SRM drives. Taking into account the requirement for effective operation and simplicity structure of converter in the limited internal environment of automobiles, the author inclines toward selecting the modified C-dump converter as well as the energy efficient C-dump converter. This is so that more economical and efficient converter topology in automobile industries can be utilized. This paper describes the foundation for the design and development of a 12V-250W-3000rpm SRM drives for automobiles. Furthermore, complete circuit, computer simulation and experiment results are presented to verify the performance of the C-dump converters.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.4
• /
• pp.141-145
• /
• 2012

In a Ubiquitous sensor network environment, the sensor node is in general small and low price, and operating with power limited battery. The reliable TCP/IP protocol is used for transmitting sensed data from the sensor node. A new method was proposed in order to overcome the limitation of small embedded memory, but it is difficult to use for the case of frame error. In this paper, a new algorithm is proposed to manage the receiving frame error or loss, and it is appropriate to the sensor network to send sensed data periodically.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.1
• /
• pp.86-92
• /
• 2009

This paper presents development of 6kw ZVS(Zero Voltage Switching) boost converter by 4-parallel operation. To realize a high capacity converter with 6 kw, 4-parallel operation of 1.5kW unit module is proposed in this paper. To meet high ratio input to output voltage, isolated type booster converter is designed. To achieve ZVS operation of 4-switches of full bridge and protect a voltage overshoot caused by switch turn-off, simple active-clamp circuit is applied to the primary side. For parallel operation of 4-modules, master-slave control method is proposed to achieve input current sharing of 4-unit converter modules accurately. For performance tests, simulation is carried out. Also, load and experimental tests of the developed booster converter, 230Vdc/6kW, are carried out under various conditions. For field tests, the developed converter is applied for boosting a battery power to high DC_link voltage for a VSI inverter which starts a micro-turbine(MT) installed in vehicle and it's performance is verified through high speed motoring a MT up to tens of thousands of rpm.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.407-410
• /
• 2002

As a part of electro-mechanical totally implantable artificial heart, a transcutaneous energy transmission system has been developed. By mutual magnetic induction between the first coil on the skin and the subcutaneously implanted second coil, the system transfers electrical power through the skin. This research aimed a minimizing the size of the implanted part as well as maximizing the transfer efficiency. When an air gap is 1$\sim$2cm, voltage gain and current gain low and it is hard to transfer energy due to large leakage flux. That is, the required input voltage and input current must be large compared with the output voltage and output current, respectively, This paper research the inverter topology and the control method in order to increase the voltage gain and the current gain. For this purpose, this inverter employs double tune to compensate the large leakage inductance of primary and secondary of the transcutaneous transformer. And the output energy of transcutaneous energy transmission system supply for Lithium-ion battery charger.

• Journal of the Korean Electrochemical Society
• /
• v.16 no.3
• /
• pp.99-110
• /
• 2013

Redox flow batteries are attractive energy-storage devices for renewable energy and peak-power energy control. Even though some prototypes are available already, many new materials are under development for new battery systems. In this reports, redox pairs and theirs properties are explained, by which one can understand issues with redox pairs, such as contaminations, cross-over, ionic selectivity, and solubility. Batteries that have the same redox pairs in both electrode compartments can be operated longer than those with different redox pairs due to the prevention form the cross-contamination. There are undivided redox flow batteries that have no membrane, which is another direction improving cycle life of the batteries.

• Journal of Sensor Science and Technology
• /
• v.24 no.2
• /
• pp.124-130
• /
• 2015

This paper presents a high performance HIGHT processor that can be applicable for CCM mode. In fact, HIGHT algorithm is a 64-bit block cipher. However, the proposed HIGHT extends the basic block length to 128-bit. The proposed HIGHT is operated as 128-bit block cipher and it can treat 128-bit block at once. Thus, it can be applicable for the various WSN applications that need fast and ultralight 128-bit block cipher, in particular, to be operated in CCM mode. In addition, the proposed HIGHT processor shares the common logics such as 128-bit key scheduler and control logics during encryption and decryption to reduce the area overhead caused by the extension of data block length. From the simulation results, the circuit area and power consumption of the proposed HIGHT are increases as 40% and 64% compared to the conventional 64-bit counterpart. However, the throughput of the proposed HIGHT can be up to two times as fast. Consequently, the proposed HIGHT is useful for USN and handheld devices based on battery as well as RFID tag the size of circuit is less than 5,000 gates.