• Journal of Environmental Science International
• /
• v.28 no.12
• /
• pp.1199-1208
• /
• 2019

Korea's protected horticulture is rapidly increasing in scale due to various advantages such as year-round harvesting, labor savings through automation and shortened culture period, and greater income generation. This study was conducted to investigate the impact of protected horticulture on water quality. The results of this study are expected to provide basic data contributing to improvements towards sustainable agriculture and eco-friendly design of protected horticulture complex. The average T-N and T-P loads from vinyl greenhouses were 286.55± 143.98 mg/L and 59.14±13.77 mg/L, respectively and those from glass greenhouses 380.68 ± 150.41 mg/L and 61.85±20.72 mg/L. The annual discharge of wastewater derived from the monthly discharge from the horticulture greenhouses were estimated at 2597 ton/ha, with the annual phosphorus load amounting to 155.3 kg/ha. The average T-N and T-P loads in the tested greenhouse effluents were in excess of 8.3- and 13.5-fold the standards for the Korean wastewater plant effluent. The waste nutrient solution discharged from a protected horticulture complex can cause water contamination. Therefore, there is a need to conduct follow-up research using a water purification system or a trench method to develop a eco-friendly protected horticulture complex for sustainable agriculture.

• Current Research on Agriculture and Life Sciences
• /
• v.21
• /
• pp.23-29
• /
• 2003

Worldwide consumption of vegetable soybean bas been increasing recently, hence it is necessary to produce good quality of soybean in our farms. In the process of vegetable soybean production threshing and seperation work accounts for about 80% of overall labor. Therefore, developing of the vegetable soybean thresher is necessary to reduce the cost of labor. The purpose of this study is to acquire the basic informations to design of the vegetable soybeans-thresher. We make the experimental system which measure the physical properties and investigate the detachment forces. Also, We calculated the minimum speed of threshing cylinder. The result are as follows; 1. The average length of soybean stem is 68.2cm. 2. The length of soybean pods are seen as 61.3mm for 3 grain, 52.6mm fer 2 grains and 41.0mm fer 1 grain 3. The widths of soybean pods are seen as 14.1mm fer 3 grain, 13.8mm fer 2 grains and 13.4mm fer 1 grain. 4. The weights of soybean pods are seen as 4.1grams for 3 grains, 2.7grams for 2 grains and 1.4grams for 1 grain. 5. The average detachment forces of pods are seen as 1.5kgf for 3 grains, 1.2kgf for 2 grains and 0.8kgf for 1 grain respectively For 1 grain, the detachment force of pods ranges from 0.2kgf to 1.4kgf. For 2 grains, the minimum detachment force of pods is seen as 0.6kgf and the maximum one is seen as 2.5kgf. For 3 grains, the minimum detachment force of pods is seen as 0.7kgf and the maximum one is seen as 2.7kgf. 6. The minimum speed of threshing cylinder is shown 6.83m/s.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.9 no.2
• /
• pp.1301-1305
• /
• 1967

Ground water flow can be studied with model test. Model test of ground water works are necessary for economic and safe design of the works. Also influence of the ground water flow to the durability and safety of hydraulic structures can be studied with this model. a. Sand model ; Water flow through porous media is the principle of sand model. Darcy's formula is the basic equation, $q=k{\frac{dh}{ds}}^{\circ}. The effect of the ground water flow on the grain system itself is represented with this model only. b. Hele-Shaw model ; In this model use is made of the viscous flow analogy. Viscous fluid such as glycerine flowing through two parallel plates depends on Poiseuille law, $q=-c{\frac{dh}{ds}}$. The analogue can be used vertically and horizontally. c. Heat model ; This is based on the analogy of the Fourier's law for heat conduction and Darcy's law for ground water flow. Especially unsteady problem can be studied with this model. A difficulty of the construction of this model is the isolation, which has to prevent losses of the heat. d. Electirc model ; Ohm's law for electric current is analogous to Darcy's law. Resistance material such as metal foil, graphite block, water with salt added, gelatine with salt added, ete. is connected to electric sources and resistor, and equi-voltage line is detected with galvanometer, $N_aCl$, $CuSo_4$, etc. are used as salt in the model. e. Membrane model ; This model is based on the facts that the deflection of a thin membrane obeys Laplace's equation if there is no load in the direction perpendicular to the membrane, and if the dellection is small.

• Journal of Technology Innovation
• /
• v.22 no.3
• /
• pp.193-223
• /
• 2014

Socio-technical systems are receiving growing attention as a core concept in the process of searching for proper solutions to sustainable growth. In this paper, we review the way for governing socio-technical transitions from a governmental perspective. Based upon the governance studies and transition research, we set social coordination and locus of transition pressures as transition contexts to differentiate transition policy governance. We propose four types of policy governance for sustainable socio-technical transitions: leading, facilitative, coordinative and persuasive. Analysis on four case based upon this typology shows different transition polices of each transition pathway in analytical aspect. It provides basic criteria for policy makers to design effective transition policies in normative aspect. Also, this paper can contribute to closing the gap between transition research and governance studies.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.33 no.3
• /
• pp.73-80
• /
• 1991

In Korea, small-scale reclaimed areas have been suffering from many problems because of the lack of comprehensive developing strategy although considerable investments have been inputed by the public sector since 1970's. For 3 reclaimed sites in Chonnam Province chosen as case study areas, the analysis, the third attempt of widely-spanned studies on areal conditions, concentrated on their living conditions. Its results were as follows : 1. Although rural residents have increased their concern on health and medical services, the public sector can only serve basic and emergent level of them, and therefore, the private sector, which is mostly placed in urban areas and costed much higher than public one, has the dominant share of those services. So, because those costs are a great expense to rural residents, their supplying system should be planned with special reference to lightening the economic burden of them. 2. By the development of locally fitted programs and innovative systems, the rural education should be qualitatively improved to deal successfully with its small scale. That will result in increasing the schooling rate to schools in rural communities, lightening the economic burden of rural residents on education services and finally activating them to contribute the betterment of rural education. 3. Servicing level of water supply, sewerage and garbage disposal in the reclaimed areas has been remaining at the lower order even in other rural areas. In the design of rural water supply, average daily consumption per capita should be changed according to the composition rate of fishing households and variety of the source of water supply. 4. Most of rural residents in the reclaimed areas want to establish the welfare facilites for the infant, youth, aged and public bath However in the long-term basis, the cooperative production and processing facilities should be considered for modernized efficient farming.

• Journal of Biosystems Engineering
• /
• v.37 no.2
• /
• pp.100-105
• /
• 2012

Purpose: Methane production potential in aerobic digestion was assessed according to feed to inoculum (F/I) ratio for food waste only, and mixing ratio of two materials for food waste and swine manure to give a basic data for the design of anaerobic digestion system. Methods: Anaerbic digestion test was performed using a lab scale batch reactor at $35^{\circ}C$ for six different feed to inoculum (F/I) ratios (0.50, 0.72, 1.14, 1.50, 2.14 and 3.41), three food waste to swine manure ratios (100:0, 60:40 and 40:60) with two different loading concentrations (10g VS/L and 30g VS/L). Results: For food waste only, the highest biogas yield of 1008 mL/gVS was obtained at 0.50 of F/I. For the co-digestion of food waste and swine manure mixture, the highest biogas yield of 1148 mL/gVS was obtained at a mixing ratio of 40:60 with loading concentration of 10g VS/L. Conclusions: F/I ratio for the food waste only, mixing ratio of food waste and swine manure, and co-substrate loading rate affected the biogas production rate. For the low loading rate, there was not so much difference according to the mixing ratio of food waste and swine manure, but for the high loading rate higher biogas yield was acquired for the co-digestion of food waste and swine manure than for the food waste alone (mixing ratio, 100:0).

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.21 no.5
• /
• pp.410-418
• /
• 2009

Based on a linear potential theory, the boundary element method(BEM) is developed and applied to analyze the hydrodynamic forces and the motion responses of a floating body with a partially reflective sidewall. The hydrodynamic forces (added mass and damping coefficients) are dependent on not only the submergence of a floating body and the reflection of a sidewall, but also the gap between body and sidewall. In particular, the partial reflection of a sidewall plays an importance role in the motion responses of a floating body at resonant frequencies. It reduces the resonant peaks caused by resonance phenomenon due to the wave trapping in an enclosed fluid domain between body and sidewall. Developed predictive tools can be used to assess the motion performance of a floating body for various combinations of configuration of a floating body, wave heading, sidewall properties, and wave characteristics and applied to supply the basic informations for the harbour design considering the motion characteristics of a moored ship.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.3
• /
• pp.193-210
• /
• 1991

For the deckhouse or superstructure, attention is directed to the reduction of vibration from a human susceptibility point of view. The two basic requirements for obtaining a low vibration level in the accommodation are to ensure that excitation forces from propeller and/or main engine are small and to avoid resonance excitation of the hull and superstructure. In recent years increased attention has been directed towards the problems of vibration and noise in deckhouse, which have caused major problems with regard to the environmental quality in the living quarters for crews. Accordingly, in this paper, the characteristic of the vibration of deckhouse of fishing boat, of which the length/height ratio is also relatively high, are studied systematically with regard to the shape and modelling of deckhouse based on finite element method of 1-dimensional, 2-dimensional and 3-dimensional model. This study is divided into 4-part. 1st part is the global deckhouse vibration, 2nd part is the local deckhouse vibration, 3rd part consists of the estimation for stiffness of foundational support and 4th part is the application to TUNA LONG LINER of 416 ton class. For the global vibration analysis, the severity of the vibration depends on the longitudinal shear and bending stiffness of the deckhouse, on the vertical deckhouse support(fore, aft and sides). However, even if the design is technically sound, vibration problems may arise due to vertical or longitudinal hull girder or afterbody resonances. Author applied the method of this study to the analysis of, deep-sea fishing vessel of G.T. 416 ton class with relatively low height and long deckhouse, and investigated the vibrational characteristic of the fishing vessel with earlier structural feature. According to this investigation, the vibration, response of above vessel was confirmed of which main hull and deckhouse behave as one body. It is at the bottom of vibrational trouble which a accommodation part of the fishing vessel is raised, that is the local vibration for side wall, fore-aft wall and deck plate of deckhouse rather than thief fect of fore-aft vibration of deckhouse for above fishing vessel. and the resonance of main hull, deckhouse and driving system such as the main engine, propeller in exciting source is mainly brought up as the trouble.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.28 no.2
• /
• pp.255-263
• /
• 2010

In order to prepare the interchange between and the unification of North and South Korea, it is needed to establish the development direction of irrigation reservoirs and formulate technological and political directions for preparing effectively against the demand of agricultural countermeasure information like the analysis of rural comprehensive development projects and the present state of agricultural land of North Korea. The purpose of this research is to construct the database of agricultural productive infrastructures and analyze the present state of irrigation reservoirs of the Yeseong River Basin in North Korea using SPOT-5 satellite imagery. As a result of the research, we were able to not only design classification items but establish method and precedure for producing thematic maps related agricultural productive infrastructure without on-site survey by analyzing present condition related to agricultural water of the basin. And we intend to provide basic data for analyzing suitabile locations of irrigation reservoirs in the basin by performing basin extraction, volume evaluation of the existing reservoirs, scale cultivative lands, benefit area fo the reservoirs, and the existing agricultural water system. In addition, we were able to understand the problem and limit in constructing the database related agricultural productive facilities.

• Journal of KIISE:Computing Practices and Letters
• /
• v.5 no.4
• /
• pp.489-497
• /
• 1999

국내의 ATM 기술은 대부분 교환기 시스템 개발에 집중되어 있었고 최근에는ATM 서비스 분야에 대한 개발 요구가 있다. 이러한 가운데 Internet 서비스는 데이타 망의 기본 서비스로 자리잡았으며, ATM망도 기본적으로 Internet 서비스를 지원하여야 한다. IETF의 IPOA (Classical IP and ARP over ATM)는 국내 망 여건 및 구현의 용이성으로 Internet 서비스를 위한 프로토콜중 가장 선호 대상이지만 RFC사양의 허술함, 구현자의 사양에 대한 이해 부족과 초기 외산 장비 제조 업체들의 자체 사양때문에 기존의 IPOA장비들과 상호 운용 시험에서 후발 IPOA 개발자는 시행착오를 겪어야만 한다. 본 논문에서는 기존 외산 IPOA 장비들과 자체 개발한 장비와 상호 운용 시험을 수행하면서 겪은 사례 연구를 정리하였고 이를 기초로 기존의 외산 IPOA와 상호 운용할 수 있는 최종 요구 사항을 제시하였다. 본 논문을 기초로 IPOA 장비를 개발한다면 국내 후발 ATM 장비 업체는 개발의 시간 및 노력을 줄일 수 있고 향후 IP/ATM 국내 기술력 향상에 도움이 될 것이다.Abstract While we have been focusing on development of ATM switching systems, recently the demand on service by use of ATM switching system is increasing rapidly. Among various ATM services, the Internet service should be provided in an ATM network since the Internet service has been the basic data service. Many domestic engineers consider the classical IP and ARP over ATM (IPOA) to be an appropriate method for interworking of IP and ATM because the IP is the network protocol used in most domestic data networks, and the IPOA is simpler and has less overhead than other approaches. However, it is not easy for a developer to implement the IPOA function module interoperable with other existing ones due to the incomplete description of IETF's RFC specifications, misunderstanding of designer and/or developer, and incompatible vendors' specifications. In this paper, we show several case studies undertaken for interoperability tests of IPOA products between our product and other vendor's products, and discuss the implementation requirement of the IPOA software to be interoperable with the existing IPOA equipment.The design and implementation requirements presented in this paper will reduce the effort of IPOA-developing engineers and time required for interoperability test. Also, this contribution will be helpful in IP/ATM interworking areas.