• Journal of Life Science
• /
• v.14 no.6 s.67
• /
• pp.963-966
• /
• 2004

The sequence of ITS (partial 16S ribosomal DNA, complete ITS1, 5.8S ribosomal DNA and ITS2, and partial 28S ribosomal DNA) was analysed by PCR and autosequencing in Sarcodon aspratus. The ITS lenght of S. aspratus was 716 base pair. As this sequence compared with other reports on S. aspratus (ace No AF335110), the sequence variation based on nucleotide deletion and substitution was $1.8\%$. This nucleotide variation rate in same species was very higher than in other species. Also, the sequence varitation rates between this S. aspratus and S. imbricatus, and S. squamus were $8\%\;and\;10\%$, respectively. This results suggested that the high sequence variation of S. aspratus might be caused specific host and inhabitat environment which limited gene flow.

• KSBB Journal
• /
• v.27 no.3
• /
• pp.167-171
• /
• 2012

A convenient liquid chromatographic enantiomer separation of several ${\alpha}$-amino acid esters as benzophenone Schiff base derivatives on covalently immobilized chiral stationary phases (CSPs) derived from polysaccharide derivatives was developed. The benzophenone imine derivatives of ${\alpha}$-amino acid esters were readily prepared by stirring benzophenone imine and the ${\alpha}$-amino acid ester hydrochloride salts in 2-propanol. The chromatographic conditions used on all CSPs were 0.5% or 5% 2-propanol/hexane (V/V) as the mobile phases at 1 mL/min of flow rate and UV 254 nm detection. The performance of Chiralpak IC among all CSPs was superior to that of the other CSPs for resolution of benzophenone imine derivatives of ${\alpha}$-amino acid esters. It is expected that the developed analytical method will be useful for enantiomer resolution of other ${\alpha}$-amino acid esters as benzophenone Schiff base derivatives.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.4
• /
• pp.325-332
• /
• 2005

This paper addresses the development of a scroll expander for power generation from relatively low temperature steam source. It has a double-sided orbiting scroll member so that no thrust bearing is needed to support the base plate of the orbiting scroll. Three power transmission shafts are placed at the periphery of the orbiting scroll base plate, and these shafts can also function as anti-rotation devices. Final output is obtained from the main central shaft engaged with the three power transmission shafts through gear assembly. The clearance between the fixed and orbiting scroll elements was estimated by comparing measurement of the mass flow rate with calculation results of a computer simulation. Due to large clearance, the expander total and volumetric efficiencies were measured to be $34\%\;and\;43\%$, respectively. It has been shown through the computer simulation that the total and volumetric efficiencies could be improved to $65\%\;and\;83\%$, respectively, if the current clearance is reduced by half.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.2
• /
• pp.113-120
• /
• 2008

Potential application of the scroll type machine to air compressor for fuel cell has been studied. Among the seven configuration factors which determine scroll wrap profile, the wrap thickness and the orbiting radius were chosen as two independent variables to generate various scroll wrap profiles. A conceptual design practice was conducted for scroll air compressor for SOFC with power output of 2 kW. With larger wrap thickness and orbiting radius, base plate area of the orbiting scroll becomes smaller, so is the axial gas force acting on the base plate, resulting in reduced thrust loss in spite of larger friction velocity. Performance analysis on the designed model showed that its total efficiency was 64.4% with the mass flow rate per unit compressor input of 0.00905 kg/(s kW) for the wrap thickness of 3.5 mm and the orbiting radius of 3.0 mm.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.281-284
• /
• 2007

The effect of Ca addition on the microstructure evolution and deformation behavior of AZ31 magnesium alloy produced by hot extrusion was investigated. For this purpose, Ca was added into AZ31 melts to the level of 0.7 and 2.0 wt.% Ca. Then, AZ31 base alloy and Ca modified AZ31 alloys were extruded at $383^{\circ}C$. Ca added alloys showed finer grain size and increased hardness value rather than AZ31 base alloy. After isothermal hot compression, the shape of tested specimen exhibited a noticeable anisotropy due to the crystallographic texture effect. The ratio of major and minor axes of ovality was not directly related to test condition and Ca amount. Flow stress level increases with the increase of Ca addition at temperature below $300^{\circ}C$ because of fine microstructure. However, at high temperature and low strain rate region ($400^{\circ}C$ and $10^{-3}s^{-1}$), reverse tendency was observed since main deformation mechanism changes from dislocation slip to grain boundary sliding or diffusional process at high temperature.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.16 no.4
• /
• pp.124-129
• /
• 2008

Design practice has been made on an oil-less scroll air compressor as an air supply device for a 2 kW fuel cell system where air pressure of 2 bar and flow rate of 120 liter/min are required. Basic structure of the scroll compressor includes double-sided scroll wrap for the orbiting scroll driven by two crankshafts connected to each other by a timing belt. These features can eliminate thrust surface which otherwise would produce frictional heat and jeopardize reliable operation of the orbiting scroll and the scroll element's deformation as well. This study focuses on optimum scroll wrap design; orbiting radius has been chosen as an independent design parameter. As the orbiting radius changes, scroll sizes such as scroll base plate and discharge port diameters change accordingly. Gas compression-related losses and mechanical loss also change with the orbiting radius. With a scroll base plate diameter of 120mm at most and discharge port of at least 10mm, the orbiting radius should be within the range of 2.5-4.0mm. With this range of the orbiting radius, it was estimated by performance analysis that the compressor efficiency reached to a maximum of ${\eta}_c$=96% at the orbiting radius of $r_s$=3.5mm for the scroll wrap height-to-thickness ratio of h/t=5.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.520-526
• /
• 2012

The appearance of the negative differential pressure(NDP), in which the shot base pressure is higher than the breech pressure, indicates that a potential damage on the gun system is increased. In order to safeguard the gun system, the igniter must be designed to minimize the NDP during the firing process. From this reason, the effect of igniter's burning rate on the NDP of the interior ballistics has been investigated through the numerical simulations. The NDP has been increased with increment of the coefficient in the burning rate of the igniter. A sudden change of the chamber pressure has been shown in case of using a singular coefficient.

• Tribology and Lubricants
• /
• v.32 no.2
• /
• pp.50-55
• /
• 2016

Recently, a double-side machining process has been adopted in fabricating a sapphire glass to enhance the manufacturability. Double-side lap grinding (DLG) is one of the emerging processes that can reduce process steps in the fabrication of sapphire glasses. The DLG process uses two-body abrasion with fixed abrasives including pallet. This process is designed to have a low pressure and high rotational speed in order to obtain the required material removal rate. Thus, the temperature is distributed on the DLG platen during the process. This distribution affects the shape of the substrate after the DLG process. The coolant that is supplied into the cooling channel carved in the base platen can help to control the temperature distribution of the DLG platen. This paper presents the results of computational fluid dynamics with regard to the heat transfer in a DLG platen, which can be used for fabricating a sapphire glass. The simulation conditions were 200 rpm of rotational speed, 50℃ of frictional temperature on the pallet, and 20℃ of coolant temperature. The five cases of the coolant flow rate (20~36 l/min) were simulated with a tetrahedral mesh and prism mesh. The simulation results show that the capacity of the generated cooling system can be used for newly developed DLG machines. Moreover, the simulation results may provide a process parameter influencing the uniformity of the sapphire glass in the DLG process.

• Journal of the Korean Vacuum Society
• /
• v.22 no.4
• /
• pp.188-192
• /
• 2013

Many studies have been conducted for preventing from diffusion between silicon wafer and metallic thin film due to a decrease of line-width and multi-layer thin film for miniaturization and high integration of semiconductor. This paper has focused on the nano-mechanical property of diffusion barrier which sample is prepared for various gas flow rate of nitrogen with tungsten (W) base from 2.5 to 10 sccm. The deposition rate, resistivity and crystallographic properties were measured by a ${\beta}$-ray back-scattering spectroscopy, 4-point probe and x-ray diffraction (XRD), respectively. We also has investigated the nano-mechanical property using the nano-indenter. As a result, the surface hardness of W-N thin film was increased rapidly from 10.07 to 15.55 GPa when the nitrogen gas flow was increased from 2.5 to 5 sccm. And the surface hardness of W-N thin film had 12.65 and 12.77 GPa at the nitrogen gas flow of 7.5 and 10 sccm respectively. These results were decreased by the comparison with the W-N thin film at nitrogen gas flow of 5 sccm. It was inferred that these severe changes were caused by the stoichiometric difference between the crystalline and amorphous state in W-N thin film. In addition, these results were caused by increased compressive stress.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.440-440
• /
• 2015

최근 급증하는 기후변화 영향으로 인한 자연재해의 위험이 증대되고 있다. 이러한 자연재해 중 가뭄은 그 빈도수나 피해의 규모가 홍수보다 작아 관련된 연구가 제한적이므로 유역의 특성을 반영한 장 단기 유출특성의 면밀한 검토가 요구되며, 향후 이를 반영한 홍수유출모형의 개발이 필요하다. 본 연구에서는 유역 수자원산정의 기초연구로서 낙동강 내성천 유역을 대상으로 유역의 유출수문자료를 구축하고 장기기저흐름지수(BFI: Base Flow Index), 표면유출지수(1-Base Flow Index)를 산정하여 유역의 유출특성을 분석하였다. 내성천유역은 낙동강 상류유역으로 본류길이는 110.69km, 유역면적은 $1,815.28km^2$이며, 분수계의 능선부가 대체로 1,000m이상의 고도를 나타내고, 유역분지의 평균 해발고도는 318.2m이다. 또한 영주댐이 검설 중에 있으며, 향후 댐 건설이 수자원에 끼치는 영향등을 분석 할 수 있는 유역이다. 본 연구에서는 내성천 유역을 분석하기 위해서 8개의 수위관측지점을 선정한 후, 2001년부터 2012년 기간의 일 유량자료를 바탕으로 유출비를 산정하였다. 내성천 8개 소유역의 유역 장기유출비를 분석한 결과 기저흐름지수는 0.24~0.47, 표면유출지수는 0.53~0.76의 분포를 나타내었다. 표면유출비는 미호(0.76), 월호(0.53), 점촌(0.71)유역을 제외한 5개 유역에서 0.62~0.65의 분포를 나타내었으므로 낙동강 상류인 내성천유역의 표면유출비로 0.63을 제시할 수 있을 것으로 판단된다. 향후 다수의 낙동강유역을 추가분석하여, 낙동강유역의 고유 유출특성을 제시 할 수 있을 것으로 기대된다.