저자(著者)는 3가지 종류(種類)의 bracket을 교정(矯正)을 위(爲)해서 발치(拔齒)한 20개(個)씩의 소구치(小臼齒)에 접착(接着)하여 24시간(時問) 후(後)에 인장강도(引張?度)를 측정(測定)한 결과(結果) 다음과 같은 결론(結論)을 얻었다. foil-mesh base bracket과 photo-etched base bracket의 평균인장강도(平均引張强度)는 통계학적(統計學的)으로 유의(有意)한 차(差)가 없으며, plastic bracket은 인장강도(引張强度) 측정(測定) 시(時) wing의 변형(變形)에 의(依)해서 정확(正確)한 측정(測定) 결과(結果)를 얻을 수 없 었다. 접착제(接着劑)가 떨어진 양상(樣相)은 foil-mesh base bracket과 photo-etched base bracket에서 접착제(接着劑)가 치아(齒牙)와 bracket 에 부분적(部分的)으로 붙어서 떨어진 것이 각기(各其) 50%로 가장 많았고, 접착제(接着劑)가 치아(齒牙)에만 붙어서 떨어진 것 (30%, 35%), 접착제(接着劑)가 bracket에만 붙어서 떨어진 것 (20%, 15%) 순(順)으로 나타났다.
본 연구는 열적 및 기계적 피로응력이 교정용 브라켓의 전단결합강도, 인장결합강도, 전단-인장 복합 결합강도에 미치는 영향과 결합상태에 미치는 영향, 그리고 접착파절 양상을 비교하는데 목적이 있다. 이를 위하여 기저부 형태가 다른 5종의 금속 브라켓을 교정치료를 목적으로 발거한 상$\cdot$하악 소구치에 부착하여, 계면에 200g의 전단-인장 복합 하중을 4주간 가한 기계적 피로시험과, 5,000회의 thermocycling을 시행한 열적 피로시험 후, 전단결합강도, 인장결합강도, 및 전단-인장 복합 결합강도를 측정하고, 파절양상을 분석하여 다음과 같은 결과를 얻었다. 1. 정적시험에서 얻은 브라켓 접착부의 결합강도는 Photoetched base가 가장 크고, Integral base가 가장 작았다(p<0.05). 모든 종류의 브라켓에서 전단결합강도가 가장 컸으며, 전단-인장 복합 결합강도는 전단결합강도의 1/3 수준으로 가장 작았다. 2. 4주간 200g의 전단-인장 복합 하중을 가한 후의 결합강도는 Photoetched base가 가장 크고, Integral base가 가장 작았으며 (p<0.05), 기계적 피로시험 후 Photoetched base와 Micro-Etched Foil Mesh base의 전단, 인장, 전단-인장 복합 결합강도가 감소하였고, Chessboard base의 전단결합강도가 감소하였다(p<0.05). 3. 5,000회의 thermocycling 후의 결합강도는 Photoetched base가 가장 컸고, integral base가 가장 작았으며(p<0.05), 열적 피로시험 후 Photoetched base와 Chessboard base, Micro-Etched Foil Mesh base의 결합강도가 모두 감소하였다(p<0.05). 4. 정적시험의 결합강도 측정 후 접착파절은 브라켓/레진 계면에서 일어났으며, thermocycling 후에는 브라켓/레진 계면과, 법랑질/레진 계면, 레진내 파절이 혼합되어 나타나 ARI 점수가 높아졌다. 기계적 피로시험 후에는 정적시험 때와 비슷한 ARI 점수를 보였다. 5. 모든 브라켓에서 thermocycling 후 브라켓/레진 계면과 법랑질/레진 계면에서 미세 균열이 관찰되었다.
금속 브라켓의 결합강도에 영향을 미치는 요소인 브라켓 기저부의 형태와 결합 부위에 적용되는 힘의 특성에 대해 알아보고자 연구를 시행하였다. 형태가 다른 5종의 금속브라켓의 기저부와 결합강도 측정후 접착파절양상을 stereoscope and scanning electron microscope를 통해 관찰하고 결합 부위에 적용되는 힘은 전단결합강도, 인장결합강도, 전단/인장복합결합강도로 구분하고 결합강도를 비교하여 다음과 같은 결론을 얻었다. 1. 브라켓 기저부 형태에 따른 모든 군에서 전단결합강토(SBS)가 제일 컸으며, 인장결합강도(TBS)는 SBS의 50%정도 수준이었고 전단/인장복합결합강도(S/TBS)는 전단결합강도(SBS)의 30%정도이었다. 2. 브라켓의 결합강도는 Micro-Loc base가 가장 크고($SBS:22.86{\pm}1.37kgf,\;TBS:11.37{\pm}1.43kgf,\;S/TBS:6.69{\pm}0.34kgf$), Integral base가 가장 작았다($SBS:10.52{\pm}1.27kgf,\;TBS:4.27{\pm}1.08kgf,\;S/TBS:2.94{\pm}0.58kgf). 3. 단위면적당 결합강도 비교시, Integral base가 가장 작았고(p<0.05), 전단결합강도와 인장결합강도에서는 Micro-Loc과 Chessboard base간의 차이가 없었으며 (p>0.05), Non-Etched Foil Mesh와 Micro-Etched Foil Mesh base간의 전단결합강도와 인장결합강도는 차이가 없었으나, 전단/인장복합결합강도에서는 Micro-Etched Foil Mesh base가 Non-Etched Foil Mesh base보다 더 크게 나타났다. 4. 전단, 인장, 전단/인장복합결합강도 측정후 접착파절은 브라켓/레진 계면에서 일어나 ARI score가 작게 나타났다.
This study was undertaken to finish the design of the adequate preadjusted bracket in Korean. The labio-lingual & bucco-lingual width of tooth & in-and-out of the bracket base was studied in normal occlusion of 17 males & 17 females. The following results were obtained. 1. The in-and-outs of the bracket base in Korean were obtained (table 2). 2. The in-and-outs of the premolar & molar were no significant due to variation according to arch wire shape in clinical practice, so the more adjustment of arch wire was required. 3. The more amount of offset was required at lateral-canine offset than at central-lateral offset in 1st order bending, due to difference of the in-and-out. 4. The degrees of the anti-rotation in molar were obtained (table 3).
Objective: The purpose of this study was to investigate whether extension of the custom base is necessary for enhancement of bond strength, by comparing the debonding forces and residual adhesives of 3 different lingual bracket systems. Methods: A total of 42 extracted upper premolars were randomly divided into 3 groups of 14 each for bonding with brackets having (1) a conventional limited resin custom base; (2) an extended gold alloy custom base: Incognito${TM}$; and (3) an extended resin custom base: KommonBase${TM}$. The bonding area was measured by scanning the bracket bases with a 3-dimensional digital scanner. The debonding force was measured with an Instron universal testing machine, which applied an occlusogingival shear force. Results: The mean debonding forces were 60.83 N (standard deviation [SD] 10.12), 69.29 N (SD 9.59), and 104.35 N (SD17.84) for the limited resin custom base, extended gold alloy custom base, and extended resin custom base, respectively. The debonding force observed with the extended resin custom base was significantly different from that observed with the other bases. In addition, the adhesive remnant index was significantly higher with the extended gold alloy custom base. Conclusions: All 3 custom-base lingual brackets can withstand occlusal and orthodontic forces. We conclude that effective bonding of lingual brackets can be obtained without extension of the custom base.
본 연구는 열을 이용한 금속 브라켓의 재생 처리시, 기저부 형태와 브라켓 재생 방법에 따른 전단접착강도 및 브라켓 탈락 양상을 비교하고자 시행되었다. 교정 치료를 위해 발거된 건전한 소구치 252개를 수집하고, Type I, Type II, Type III 스탠다드 브라켓을 각각 재생 방법에 따라 네 군으로 나누어 준비된 소구치에 접착하고, Instron Universal Testing Machine(Model 4466)으로 전단접착강도를 측정하였으며, 브라켓의 탈락 양상을 관찰하고 브라켓 기저부의 주사전자현미경 소견을 관찰하였다. SPSS 통계처 리 프로그램을 이용하여 일원분산분석(oneway ANOVA), Scheffe's multiple range test를 실시하여 다음과 같은 결론을 얻었다. 1. 브라켓 기저부 형태에 따른 전단접착강도는 유의차가 있었으며(p<0.001), 그 크기는 Type III(round indentation, micro-etched base), Typ I(foil-mesh base), Type II(grooved integral base, micro-etched)의 순이었다. 2. 생 방법에 따른 전단접착강도는, Type I, Tpe II 브라켓에서는 Big Jane에 1분간 처리시 우수한 결과를 보였고 (p<0.05), Type III 브라켓에서는 각 군간 유의한 차이를 보이지 않았다(p>0.05). 3. Type I, Type II 브라켓은 기저부-레진 계면에서 가장 높은 빈도로 탈락하였고, Type III 브라켓에서는 레진의 절반 가량이 치면에 잔존하는 탈락 양상이 가장 많았다. 4. 탈락 양상에 따라 탈락시의 전단접착강도가 유의성 있는 차이를 보였는데(p<0.05),브라켓 탈락시 접착제의 절반 가량이 치면에 잔존하는 경우 전단접착강도가 가장 큰 것으로 나타났다. 5. 브라켓 재생 후 기저부에 남아 있는 접착제는 전단접착강도의 감소에 영향을 미치지 않았다.
The purpose of this study was to evaluate the in vitro shear bond strengths to enamel and the failure sites of three ceramic brackets and one metal bracket in combination with light cured orthodontic adhesive. The brackets were divided into four groups. Each ceramic bracket group had different bonding mechanisms with adhesive. Group A; metal bracket with foil-mesh base (control group) Group B; ceramic bracket with micromechanical retention Group C; ceramic bracket with chemical bonding Group D; ceramic bracket with mechanical retention and chemical bonding. Forty extracted human lower first premolars were prepared for bonding and 10 brackets for each group were bonded to prepared enamel surfaces with $Transbond^{\circledR}$ light cured ortho dontic adhesive. Twenty four hours after bonding, the Instron universal testing machine was used to test the shear bond strength of brackets to enamel. After debonding, brackets and enamel surfaces were examined under stereoscopic microscope to determine the failure sites, Statistical analysis of the data was carried out with ANOVA test and $Scheff\acute{e}$ test using SPSS PC+. The results were as follows. 1 . There were statistically significant differences in mean shear bond strengths of three ceramic bracket groups (p < 0.05). Shear bond strengths of group C and D were significantly higher than that of group B and shear bond strength of group C was significantly higher than that of group D. 2. Group C and D both had significantly higher shear bond strengths than metal bracket (group A), but there were no significant differences in shear bond strengths between group A and B (p < 0.05). 3. The failure sites of four bracket groups were also different. Group C and D failed primarily at enamel-adhesive interface, but group A and B failed primarily at bracket base-adhesive interface. 4. Among all ceramic bracket groups, group B was very similar to metal bracket in the aspect of shear bond strength and failure site.
The purpose of this study was to evaluate the effects of different bases of ceramic brackets on shear bond strength and to observe failure patterns of bracket bondings. Lower bicuspid brackets whose bases designed for the macromechanical and silane treated chemical bonding those for silane treated chemical bonding, those for micromechanical bonding, and those for macromechanical bonding were tested as experimental groups, and foil mesh-backed metal brackets as a control group. All the brackets were bonded with $Mono-Lok\;2^{(TM)}$ on the labial surface of extracted human lower bicuspids after etching the enamel with $38\%$ phosphoric acid solution for 60 seconds. The shear bond strengths were measured on the universal test machine after 24 hours passed in the $37^{\circ}C$ water bath. The gathered data were evaluated and tested by ANOVA and Duncan's multiple range test, and those results were as follows. The shear bond strengths of brackets for macromechanical and chemical bonding, those for chemical bonding, and those for micromechanical bonding were not different (p>0.05), but showed statistically higher than those of metal bracket and those of ceramic bracket for micromechanical bonding(p<0.05). The shear bond strengths of ceramic bracket for micromechanical bonding showed statistically lower than those of metal bracket(p<0.05). The enamel fractures and/or ceramic bracket fractures were observed in the cases of higher bond strength than that of metal bracket. These results supported that silane treated base of ceramic bracket show higher shear bond strength than that of metal bracket, and suggested that micromechanical form of ceramic bracket bases show higher shear bond strength than that of macromechanical form.
본 연구는 교정용 금속 브라켓에 다양한 방향에서의 복합적인 응력을 가하여 힘의 방향과 적용점에 따른 교정용 브라켓의 결합강도를 비교하고, 브라켓의 유지력을 평가하는데 기준이 되는 최소결합강도의 특성에 대해 알아보고자 시행되었다. 일정 한 표면특성을 갖는 금속봉에 Micro-Loc base, Chessboard base, Non-etched Foil-Mesh base 등 서로 다른 기저 면 형태를 가지는 3가지 종류의 금속 브라켓을 부착시키고, $0^{\circ},\;15^{\circ},\;30^{\circ},\;45^{\circ},\;60^{\circ},\;75^{\circ},\;90^{\circ}$의 Peel 결합강도$(_0PBS, \;_{15}PBS,\;_{30}PBS,\;_{45}PBS,\;_{60}PBS,\;_{75}PBS,\;_{90}PBS)$ 및 전단결합강도(SBS)와 인장결합강도(TBS)에 대한 브라켓의 결합강도를 측정하고, 각 브라켓의 기저면 면적을 고려하여 단위면적당 결합강도를 산출하여 비교한 결과 다음과 같은 결론을 얻었다. 1. Micro-Loc base와 Chessboard base 및 Non-etched Foil-Mesh base 브라켓 모두에서 전단결합강도(SBS)가 가장 컸다(P<0.01). 2. Peel 응력의 방향 변화에 따른 peel 결합강도(PBS)의 변화양상은 Micro-Loc base와 Chessboard base, Non-etched Foil-Mesh base 브라켓 모두에서 유사하였으며 (p>0.05), peel 응력의 적용 각이 증가할수록 peel 결합강도(PBS)는 감소하였고 $60^{\circ}$에서 최저값을 보였다(p<0.05). 3. Micro-Loc base에서 최저 peel 결합강도$(_{60}PBS)$는 전단결합강도(SBS)의 $29\%$ 수준이었으며, 인장결합강토(TBS)에 대해서는 $52\%$ 수준이었고, Chessboard base에서 최저 Peel bond strength$(_{60}PBS)$는 전단결합강도(SBS)의 $34\%$ 수준이었으며, 인장결합강도(TBS)에 대해서는 $61\%$ 수준이었으며, Non-etched Foil-Mesh base에서 최저 Peel 결합 강도$(_{60}PBS)$는 전단결합강도(SBS)의 $34\%$ 수준이었으며, 인장결합강도(TBS)에 대해서는 $55\%$ 수준이었다. 4. 단위 면적 당 결합강도에 있어서 전단결합강도(SBS)와 인장결합강도(TBS) 및 $75^{\circ}\;와\;90^{\circ}$ peel 결합강도는 Micro-Loc base와 Chessboard base에서 차이 가 없었으며 Non-etched Foil-Mesh base에서 가장 작았고(p<0.05), $0^{\circ},\;15^{\circ},\;30^{\circ},\;60^{\circ}$ peel응력을 적용한 결과 Chessboard base에서 가장 큰 Peel결합강도를, Non-etched Foil-Mesh base에서 가장 작은 결합강도를 보였다(p<0.05).
Purpose: The primary objective of this study was to evaluate the change in the temperature of the adhesive resin in polycrystalline ceramic brackets irradiated using a diode laser at different irradiation energy levels and times. Materials and Methods: For the measurement of the temperature of the adhesive resin, it was applied at the base of the ceramic bracket, a thermocouple was placed at the center of the base surface, the bracket was placed on prepared resin specimens for light curing, and a laser was irradiated to the center of the bracket slot at 5, 7, and 10 W. For the measurement of the temperatures of the enamel under the bracket and pulp cavity, extracted premolar was fixed to a prepared mold and the ceramic bracket was bonded to the buccal surface of the premolar. The Kruskal-Wallis H test and Friedman test were used for statistical analysis. Result: At 5 W, the temperature of the adhesive resin did not reach the resin softening temperature of 200℃ within 30 seconds. At 7 W, it reached 200℃ when the ceramic bracket was irradiated continuously for 28 seconds. At 10 W, it reached 200℃ when the ceramic bracket was irradiated continuously for 15 seconds. During laser irradiation, the temperature of the enamel under the bracket increased by over 5℃ within 15 seconds. Conclusion: The use of diode laser irradiation for bracket debonding should be carefully considered because the pulp cavity temperature increases by over 5℃ within the irradiation time for resin thermal softening.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.