• 약학회지
• /
• 제36권6호
• /
• pp.538-547
• /
• 1992

Optimal synthetic condition of barium sulfate were investigated from the viewpoint of yield and bulkiness according to a randomized complete block design proposed by G.E.P. Box and K.B. Wilson. Barium chloride and magnesium sulfate were utilized as reactants in order to prepare barium sulfate in this study. It was found that optimum temperature range of reactant solutions was $60{\sim}100^{\circ}C$ and the optimum concentration range of the reactant solutions was $10{\sim}17.3%$ and $10{\sim}20%$ respectively, on the viewpoint of yield and bulkiness. The optimum mole ratio of $BaCI_2$ to $BaSO_4$ was in the range of $1.50{\sim}2.0$ and the optimum mole ratio of $BaCI_2$ to $BaSO_4$ was in the range of $1.50{\sim}2.0$ and the optimum reacting time range was $15{\sim}20$ minutes. The optimum drying temperature range was $110{\sim}130^{\circ}C$ from the viewpoint of yield, but it was $90{\sim}110^{\circ}C$ on the basis of bulkiness. Apparent viscosity of barium sulfate suspensions dispersed in various concentrations of Na. CMC was measured by using Brookfield synchrolectric viscometer model LVT, the relative equation, log ${\eta}_{sp}=A+B.{\phi}$ was examined and the equation was found to agree fairly well. 1 w/v% Na. CMC aqueous solution and 0.1 volume fraction of $BaSO_4$ powder were optimum in the preparation of $BaSO_4$ suspension showing highest viscosity at infinite shearing.

• 대한화장품학회지
• /
• 제30권2호
• /
• pp.197-200
• /
• 2004

감촉 및 광학적 요소는 파우다 파운데이션에 있어서 매우 중요한 요소이다. 이러한 감촉과 광학적인 요소를 동시에 만족하는 분체에 관심을 가지고 다양한 소재 및 제조방법을 연구 중에 바륨설페이트를 기본 입자로 하는 복합화 된 분체를 개발하게 되었다. 바륨설페이트는 입자의 모양이 매우 넓고 표면의 굴곡이 없는 판상으로 감촉면에서 부드러운 사용성과 균일한 부착 특성을 나타내며 굴절율도 피부보다 약간 높은 수준으로 인위적이지 않고 자연스러운 광학적 특성을 나타내고 있다. 그러나 파운데이션에서 요구되는 광학적 특성인 자외선 차단능력이나 커버력, 블루밍 효과에 있어서는 기대수준에 못 미치는 것을 알 수 있었다. 이러한 특징은 파우다 파운데이션에서 사용되는 대부분의 분체에 있어서 공통적으로 나타나는 특성으로 감촉적인 측면(소프트, 밀착력 등)과 광학적 측면(커버력, 자외선 차단력 등)을 동시에 만족하는 분체가 극히 드문 것을 알 수 있다. 본 연구에서는 이러한 점을 극복하고자 감촉적인 측면에서 우수한 바륨설페이트를 모입자로 하고 자외선 차단능력과 블루밍에서 우수하나 자체의 응집력이 강하고 사용감이 거친 특징을 나타내고 있는 티타늄디옥사이드를 자입자로 하여 복합화하려 하였다. 이때 중요 요소로 복합화 되는 티타늄디옥사이드의 함량에 따라 복합안료의 감촉적인 측면과 분산력 등이 민감하게 달라지는 것을 알 수 있었다. 이에 패널을 이용하여 복합안료의 사용성에 영향을 미치지 않는 수준의 함량을 결정하여 복합화 처리했으며, 사용자가 피부에 도포시 발생되는 피지나 땀에 대한 변색과 사용감을 고려하여 피지나 땀에 강한 발수, 발유 능력을 나타내며 부드러운 감촉의 디메치콘으로 복합안료를 코팅 처리하여 복합분체를 만들게 되었다. 이렇게 만든 복합분체(barium sulfate/TiO$_2$/dimethicone)를 패널을 이용한 테스트와 기기를 이용한 테스트를 실시하여 효과를 검증하게 되었다.

• 대한방사선협회지
• /
• 제28권1호
• /
• pp.49-54
• /
• 2002

Purpose : The objective of the study is to compare and examine the efficacies of barium enema and air reduction as infantile intussusception treatment. Objects and Methods: A retrospective research was conducted on infantile intussusception patients from

• 한국물환경학회지
• /
• 제33권4호
• /
• pp.416-423
• /
• 2017

The subject samples include 150 and 170 samples collected from intake holes in the former and latter half of 2015, respectively. They were analyzed with ICP-MS. The average concentration of detected barium was $10.54{\mu}g/L$ ($0.23{\sim}168.22{\mu}g/L$) and $8.21{\mu}g/L$ ($0{\sim}255.65{\mu}g/L$) for the former and latter halves of 2015, respectively. The concentration distribution was the highest for the precambrian era at $19.07{\mu}g/L$ and the lowest Cenozoic era at $4.92{\mu}g/L$. The average value for sedimentary, metamorphic, and igneous rocks was $7.84{\mu}g/L$, $20.84{\mu}g/L$, and $9.47{\mu}g/L$, respectively, which indicates that it was the highest for metamorphic rocks. The study also analyzed correlations between barium and other minerals and found that magnesium recorded 0.44 and 0.71 for the former and latter half of 2015, respectively. As for barium concentration according to depth, it was relatively low in shallow groundwater (under 200 m) with its average concentration at $14.33{\mu}g/L$ and $14.71{\mu}g/L$ for the former and latter half of 2015, respectively. It was $8.53{\mu}g/L$ and $4.04{\mu}g/L$ in deep groundwater (over 200 m) for the two periods, respectively, The risk assessment results show that its average risk was HQ 0.00139 and HQ 0.00163 for the former and latter half of 2015, respectively, being considerably lower than "1", which suggests that barium poses few possibilities of consumption risk.

• 한국융합학회논문지
• /
• 제8권2호
• /
• pp.113-120
• /
• 2017

본 실험에서는 전산화단층영상장비에서 패각을 이용하여 제작한 방사선 융합차폐체의 표면 방사선 감소율과 방사선 인공물 영상을 평가하고자 하였다. 방사선 융합차폐체는 실리콘, 패각, 바륨분말을 이용하여 직경 50 mm, 두께 3.5 mm의 원형 차폐체 5종 (실리콘 차폐체, 바륨 차폐체, 실리콘과 패각 혼합 차폐체, 실리콘과 바륨 혼합 차폐체, 실리콘과 패각 그리고 바륨 혼합 차폐체)을 제작하였다. 방사선발생과 획득은 4 다중채널 전산화단층영상장비를 이용하였다. 그 결과 실리콘과 패각 혼합 차폐체가 영상의 인공물 발생 없이 5.3%의 표면 방사선 감소효과가 있었다. 향후 다양한 형태를 만들 수 있는 실리콘의 장점과 패각의 재활용으로 인한 친환경적인 소재로 방사선 융합차폐체 제작에 도움을 줄 수 있으리라 기대한다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제24권2호
• /
• pp.53-57
• /
• 2001

The purpose of this study is to investigate the contamination rate of barium sulfate suspension made in the exposed state in usual circumstances. This study was performed in four university hospital using the contrast media by barium sulfate powder. The specimen were detected at dispensing water, agitator and mixing tank. We also classified the suspension into general bacteria, mycete, and Bacillus coli infection. The tap water were used to dispense water in the all hospitals. Bacillus colt were not detected in the all. General bacteria and mycete were not detected in the one specimen, but detected in two specimen over defined value. In the contamination rate of agitator, mixing tank, and the manufactured, Bacillus coli were not detected in all. However, general bacteria and mycete were detected too numberous to count. In conclusion, the refined water must be used in dispensing water in manufacturing suspension. The disinfectant is also used in washing the agitator and mixing tank for sterilization. Hand washing is indispensible to manufacturing suspension for preventing from infection.

• Elastomers and Composites
• /
• 제30권3호
• /
• pp.218-228
• /
• 1995

To make filler loaded conducting rubber which has excellent electronical and physical properties, CR and NBR were mixed with barium ferrite(BaO.6Fe2O3). From the result of this study, vulcanization characteristics shows that curve is upgraded as the filler concentration increases and CR has higher torque than NBR. In physical properties, elongation being higher, modulus comes to decrease. Tear strength gradually decrease after showing the maximum point when is in the 100phr in CR. Resilience is not good to cause the increase in filler concentration. In electrical properties, conductivity becomes low when filler concentration increase. The increase of voltage makes a conductivity grown, but the rate change is weak. The influence of temperature hardly changes on increasing temperature. The morphology and the dispersion of a conductivity filler in vulcanizates through SEM were good. The more filler concentration increases, the shorter the particle interval is.

• 한국방사선학회논문지
• /
• 제7권6호
• /
• pp.403-408
• /
• 2013

본 연구에서는 기존의 납을 대체할 수 있는 의료 방사선 차폐제품 적용을 위해 몬테카를로 시뮬레이션을 통해 바륨화합물의 두께별 차폐능을 모의 추정하였다. 차폐재 물질로는 황산바륨($BaSO_4$)을 이용하였고, 시편의 면적은 $15{\times}15cm^2$, 황산바륨의 밀도는 $4.5g/cm^3$, 납의 밀도 $11.34g/cm^3$를 적용하여 차폐재 시편의 두께를 0.1 mm부터 5 mm까지 시뮬레이션 하였다. 입력 선원은 연속 X-ray 에너지 스펙트럼(40 kVp ~ 120 kVp)에서 10kVp Step으로 시뮬레이션하였다. 40 kVp ~ 60 kVp에서의 흡수확률은 3 mm ~ 5 mm 두께에서는 납과 동일한 차폐능을 나타내었으나, 2 mm 이하에서는 차폐능이 기존 납 차폐재에 비해 다소 차폐능이 떨어지는 결과로 나타났다. 또한 70 kVp ~ 120 kVp 에너지 대역에서의 차폐능은 기존 납 차폐재와 유사한 성능을 보였지만, 0.5 mm 이하에서는 다소 낮은 차폐능으로 모의 추정되었다. 본 연구는 몬테카를로 시뮬레이션을 통해 의료용 엑스선 에너지 대역에 대한 두께 함수로써 바륨화합물의 차폐능을 추정하여 기존의 납과 비교 분석하였다. 또한 순수한 황산바륨의 의료용 방사선 차폐제품 적용가능성을 검증하고자 하였다. 그 결과 의료 방사선 에너지 대역 70 kVp ~ 120 kVp 에서 최소 2 mm 이상의 바륨화합물 두께에서 기존 납 1.5 mm 대비 95% 이상의 차폐효과가 있는 것으로 추정되었으며, 본 결과는 의료용 방사선 차폐제품의 경량화 제작에 기초 자료로 제공될 수 있을 것으로 사료된다.

• 한국응용과학기술학회지
• /
• 제22권4호
• /
• pp.306-314
• /
• 2005

In this study, spherical $pre-BaTiO_3$ particles are prepared by gelation and aging process in autoclave without catalysts. The (Ba-Ti) gel used as a starting material was prepared by aging mixtures of titanyl acylate with barium acetate aqueous solution([glacial acetic acid (AcOH)]/[titanium isopropoxide (TIP)] 4, [barium acetate]/[TIP] 1) at $45^{\circ}C$ for 48hrs. XRD and SEM results for the (Ba-Ti) gel sample at aging process showed that the gel was formed via aggregation of the fine particles. It seems to be the primary particles of bulk (Ba-Ti) gel amorphous, but the spatial arrangement of barium and titanium in the (Ba-Ti) gel is similar to that in crystalline $BaTiO_3$ particles. From XRD and FT-IR. spectroscopy analysis it was found that the crystal structure of the prepared particles continuously transformed from amorphous to tetragonal as the calcination temperature increased, and crystallized spherical cubic and tetragonal $BaTiO_3$ powder obtained at the very low calcination temperature between $500^{\circ}C$ and $900^{\circ}C$ after 1hrs of heat treatment respectively. According to BET analysis result, final particle have pore structure of ink bottle shape which is produced by aggregation of fine spherical particles with surface area of $280m^2/g$ and average pore size of 130nm.

• Journal of Magnetics
• /
• 제5권2호
• /
• pp.40-43
• /
• 2000

Acicular $\alpha-FeOOH\; and\; Ba(OH)_2\cdot8H_2O$ are starting materials in this study. This paper presents the characteristics of the contents of citric acid and heating condition for preparing acicular barium ferrite powder. They control particle shape, crystalline phase, magnetic properties of acicular barium ferrite powder So the effects of the contents of citric acid and heating condition are studied. The experimental condition for starting materials were 800~1000$\circ C$ in firing and 0~40 wt% citric acid, respectively, Ba-ferrite particles fired at the range of 800 $\circ C$to 900 $\circ C$ were maintained as acicular particle shape, but there were mixed particles of acicular and round shape after fired at 950 $\circ C$. Ba-ferrite powder of the single phase was obtained in firing at 900~1000$\circ C$ and with 20 wt.% citric acid. There were unreacted phase of $\alpha-Fe_2O_3 \;and \; BaFe_2O_4$ phases as a second phase in case of sintering at below 850 $\circ C$. Acicular barium ferrite powder of single phase was also produced in firing at 900 $\circ C$ with 20 wt.% citric acid. The saturation magnetization of single phase of acicular $BaFe_12O_19$powder was about 51 emu/g and coercivity was about 4200 Oe.