• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.1
• /
• pp.20-26
• /
• 2003

This paper presents hairpin-comb bandpass filter using ground aperture. Hairpin-comb resonator maintains the weak coupling though the space between two resonators is very small. This has the good merit that the entire filter size is small for narrowband bandpass filter. The coupling between two hairpin-comb resonators so very weak that can't be applicable to general microstrip. We compensate the coupling by using ground aperture. It makes the hairpin-comb filter possible that can be applicable to general microstrip. Also it has the good merit which adjusts the bandwidth by changing the size of aperture without changing the space. In this paper, we fabricate the bandpass filter, which has 1.78 GHz center frequency and 62 MHz (3.5%) fractional bandwidth.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.3
• /
• pp.565-573
• /
• 2000

In this paper, a interdigital microstrip bandpass filter is designed. A interdigital microstrip bandpass filter has many advantages such as insertion return loss, lower return loss, higher frequency selectivity and smaller in size in comparison with the conventional coupled line filter. A interdigital microstrip bandpass filter consists of quasi TEM-mode strip line resonators between parallel ground plant. Each resonator element is a quarter wavelength long of the center frequency and is short circuited at one end and open circuited at the other end. In the filter design, Ensemble software is used. Experimental results show that the bandwidth of interdigital microstrip bandpass filter is 2.52GHz, insertion loss is -1.8dB and return loss is -17.0dB at 11.20Hz.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.5
• /
• pp.965-970
• /
• 2018

In this paper, the transition of the folded substrate integrated waveguide (FSIW) using two substrates is suggested and applied to the bandpass filter. The FSIW has similar characteristics with the SIW and can be reduced the width of the SIW. The transition between the FSIW to the microstrip is designed by using shorted quarter wavelength line. Also, the bandpass filter is designed by using the FSIW and the elliptic lowpass filter of 5 section. Fabricated bandpass filter has the center frequency of 5.75 GHz and the bandwidth of 33.2%. Also, the insertion loss and return loss at the center frequency are 0.63dB and 19.1dB, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.1
• /
• pp.14-19
• /
• 2003

In this paper, a λ/4 hair-pin resonator is proposed to reduce the size of resonators. A LTCC MLC bandpass filter is designed using the λ/4 hair-pin resonators. The electromagnetic coupling structure between two planar resonators is analysed. The equivalent circuit is derived to explain the behavior of the LTCC MLC bandpass filter using λ/4 hair-pin resonators. A design procedure is also described. The simulated and measured results of 1.8 GHz band 2-pole bandpass filter are presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.3
• /
• pp.237-242
• /
• 2002

In this paper, active inverter bandpass filters using the impedance matching method are designed and fabricated. The designed active inverter bandpass filter is fabricated using microstrip-lines matching networks for IMT-2000 applications. Measured results show that the two-pole inverter bandpass filter for IMT-2000 application has its insertion gain of 14.1 ㏈, 75 MHz bandwidth at the center frequency 2.18 GHz and more than 23 ㏈ attenuation at fo $\pm$ 200 MHz.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.10
• /
• pp.4745-4750
• /
• 2012

In this paper a $6^{th}$ 1MHz~30MHz bandpass filter for Power line communication(PLC) modem receiver is designed using current mode synthesis method which is good to design the low-voltage and low-power filter. The designed bandpass filter is composed of cascade connecting between $3^{rd}$ Butterworth highpass filter and $3^{rd}$ Chebychev lowpass filter. As a core circuit in the current-mode filter, a current-mode integrator is designed with new architecture which can improve gain and unity gain frequency of the integrator. The gain and the unity gain frequency of the designed integrator is each 32.2dB and 247MHz. And the cutoff frequency of the designed $6^{th}$ bandpass filter can be controlled to 50MHz from 200KHz according to controlling voltage and the power consumption is 2.85mW with supply voltage, 1.8V. The designed bandpass filter was verified using a $0.18{\mu}m$ CMOS parameter.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.11
• /
• pp.1728-1735
• /
• 1989

A design procedure for microstrip bandpass filters using step impedance resonators (SIR's) and tapped input/output to a conventional parallel coupled line bandpass filter is presented. The filter configuration consisting of both half-wavelength and SIR's suppreses to spurious resonance response near the second harmonics, while tapping techniques offer benefit in situations where the impractical. The measured frequency responses of the designed filter are in close agreement with the computed responses.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.2 no.4
• /
• pp.10-16
• /
• 1991

A microstrip bandpass filter using stepped impedance resonators and tapped input / output is realized with Teflon substrate, whose center frequency is 3.5 GHz and fractional bandwidth is 20%. In order to realize a wider bandwidth of 30%, the Crystal's design method and the input / output tapping scheme are used. Another microstrip filter designed as mentioned above is realized with Epsilam-10 substrate. This case shows good agreement between the theoretical responses and the measured ones.

• Current Optics and Photonics
• /
• v.3 no.6
• /
• pp.590-596
• /
• 2019

To improve the color gamut of a liquid-crystal display (LCD), we propose a bandpass filter that is added to the backlight unit to optimize the backlight spectrum. The bandpass filter can only transmit red, green and blue light in the visible range, while reflecting the unwanted light. We study the optical properties of the bandpass filter using the transfer-matrix method, and the effect of the bandpass filter on the color gamuts of LCDs is also investigated. When a bandpass filter based on a 5-layer configuration comprising low and high refractive indices ((HL)²H) is used in phosphor-converted white-light-emitting diode (pc-WLED), K₂SiF₆:Mn⁴⁺ (KSF-LED), and quantum-dot (QD) backlights, the color gamuts of the LCDs improve from 72% to 95.3% of NTSC, from 92% to 106.7% of NTSC, and from 104.3% to 112.2% of NTSC respectively. When the incident angle of light increases to 30°, the color gamuts of LCDs with pc-WLED and KSF-LED backlights decrease by 2.9% and 1% respectively. For the QD backlight, the color gamut almost does not change. When the (HL)²H structure is coated on the diffusion film, the color gamut can be improved to 92.6% of NTSC (pc-WLED), 105.6% of NTSC (KSF-LED), and 111.9% of NTSC (QD). The diffusion film has no obvious effect on the color gamut. The results have an important potential application in wide-color-gamut LCDs.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.7 s.361
• /
• pp.37-44
• /
• 2007

A low-voltage high-linear bipolar OTA and its application to IF bandpass filter for GSM cellular telephone are presented. The OTA consists of a low-voltage linear transconductor, a translinear current gain cell, and three current mirrors. The bandpass filter is composed of two cascaded identical second-order bandpass filters, which consist of a resistor, a capacitor, and a grounded simulated inductor realized with two OTA's and a grounded capacitor. SPICE simulations using an 8 GHz bipolar transistor-array parameter show that the OTA with a transconductance of 1 mS exhibits a linearity error of less than ${\pm}2%$ over an input voltage range of ${\pm}0.65\;V$ at supply voltages of ${\pm}2.0\;V$. Temperature coefficient of the transconductance is less than $-90ppm/^{\circ}C$. The bandpass filter has a center frequency of 85 MHz and Q-factor of 80. Temperature coefficient of the center frequency is less than $-182ppm/^{\circ}C$. The power dissipation of the filter is 128 mW.