• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.5
• /
• pp.42-49
• /
• 1994

In this paper we consider efficient 1-D and 2-D linear-phased half-band filter designs. We first introduce a new derivation of the existing Vaidynathan-Nguyen 's half-band filter design method, which verifies that the design provides optimal half-band filters. We then propose an approximately-linear-phased IIR half-band filter design method, which is based on the all-pass equalizer design with the linear phase -$\omega$/2. Finally, we propose an efficient method to design optimal 2-D half-band filters, for which we utilize a 2-D all pass prototype filter of half the order of the desired 2-D half-band filters.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.5
• /
• pp.872-882
• /
• 1994

In this paper, the Low Noise Amplifier(LNA) is designed and fabricated to include a band pass filter characteristics considering the antenna system characteristics according to the transmitting and receiving signal level of communication satellite transponder. As an example, a 2-stage low noise amplifier and a 4-stage amplifier and designed, fabricated and measured at 14,0~14.5GHz of receiving frequency band. This fabricated LNA has shown the gain with very good flatness within pass-band, and its gain decreases rapidly out of band resulting in supperssion of the transmitting signal power leakage. It has shown the 20.3dB +- 0.1dB of pass-band gain, the 1.44dB +-0.04dB of noise figure and the 14dB rejection out of band(12.25~12.75GHz). The gain flatness, noise figure and group delay of this 2-stage LNA satisfactorily met the simulation results. And the fabricated 4-stage amplifier has shown the more than 42dB of pass-band gain, the +-0.25dB of flatness and the 28dB of the rejection effect for transmitting power leakage. The 2-stage LNA and 4-stage amplifier, in this paper, will bring a design margin for the input filter and also result in the system cost reduction.

• 한국정보통신설비학회:학술대회논문집
• /
• 2009.08a
• /
• pp.215-218
• /
• 2009

In this paper, Dual-band bandpass filter studied design using Parallel Coupled SIR(Stepped Impedance Resonator). This Dual-band bandpass filter design SIR of half-wavelength by Parallel-coupled type that is available to RFID system and Changed structure in Meander form by size reduce. Because seen Dual-band bandpass filter is designed so that is applicable for frequency 433MHz and 2.45GHz of RFID system is very wide distance between two pass-band, establish 433MHz by fundamental frequency and controlled 2.45GHz by 2st spurious resonance frequency bandstop filter of 1st spurious resonance frequency and Parallel coupled SIR Combine to remove 1st spurious resonance frequency.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2002.05a
• /
• pp.44-50
• /
• 2002

The fast Fourier transform (FFT) is a good method to estimate spectral density, but the frequency resolution is limited to the sampling window, and thus the precise characteristics of the spectral density for short signals are not clear. To solve the limitation, a multiple band-pass filter was introduced to estimate the precise time course of the spectral density for flash visual evoked potentials (VEPs). Signals were recorded during -200 and 600 ms using balanced noncephalic electrodes, and sampled at 1 K Hz in 12 bits. With 1 Hz and 10 ms resolutions, spectral density was estimated between 10 and 100 Hz. Background powers at the alpha-and beta-bands were high over the posterior scalp, and powers around 200ms were evoked at the same bands over the same region, corresponding to P110 and N165 of VEPs. normalized's spectral density showed evoked powers around 200 ms and suppressed powers following the evoked powers over the posterior scalp. The evoked powers above the 20Hz band were not statistically significant. However, the gamma band was significantly evoked intra-individually; details in the gamma bands were varied among the subjects. Details of spectral density were complicated even for a simple task such as watching flashes; both synchronization and desynchronization occurred with different distributions and different time courses.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.6
• /
• pp.533-539
• /
• 2004

In this work, in order to realize a band pass filter with wide-band characteristics for mobile communications, 2 GHz band pass filter was designed using ring resonator with stub. The three stage wide-band BPF was designed and fabricated. For broadband design, the ring circumference was divided by 4 sections with 1/8 wavelength and 2 sections with 1/4 wavelength which have different line impedances. The characteristics of the proposed BPF were highly improved by using three stage ring resonator. The characteristic impedance values of each sections were obtained by Powell's least square algorithm where differentiations are not needed. The measured results showed a good agreement with the theoretical results as well as ADS simulation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.05a
• /
• pp.133-136
• /
• 2008

In this paper, the parallel coupled line(PCL) band-pass filter satisfying IEEE 802.11a (a:$5.15{\sim}5.25$, b:$5.25{\sim}5.35$, c:$5.725{\sim}5.875$ [GHz]) has been designed for 5[GHz]band W-Lan RX-System applications. The designed PCL Band-Pass filter is of advantage to make a design formula that is small, light and approximate accuracy. It choose a microstrip plane figure because it is possible that a multiplicity of resonator was designed. It was shown that bandwidth was 14% from 5.15GHz to 5.92GHz at the -3dB designed filter. As a result, it is enough to use the designed filter at W-LAN RX-system of the 5GHz band.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.31-34
• /
• 1998

CDMA base station SAW filter has been designed and fabricated successfully. Through the computer simulation, SAW filter is designed to have center frequency of 69.99MHz, ripples lower than 0.7dB and rejection level lower than 50dB. To obtain low noise band pass SAW filter, Input electrode has a apodization type and output electrode has a withdrawal type. For the fabrication of the SAW filter, Al thin film is deposited to the quartz substrates. The fabricated SAW filter has center frequency of 70.5MHz, ripples of 1dB and rejection level of 45dB.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.10 no.3
• /
• pp.47-54
• /
• 1996

In this paper, the band pass filter was designed and constructed for personal communication services of information facilities. For the band pass filter design, after dielectric resonator structures were analyzed. J-inverter design theory and its simulation method were studied. The parameters obtained from design theory were practically applied to filter construction. The simulation results are well agreed with the measured result of constructed filter after fine tunings.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.195-196
• /
• 2008

A ring resonator based band-pass filter enabling enhanced sideband suppression was proposed and demonstrated. It is composed of a single-ring based-pass section combined with a band-rejection section based on two different coupled rings. As for the achieved device performance, bandwidth was reduced from 98 MHz to 48 MHz by about 51% with no remarkable excessive insertion loss as expected. And the quality factor of the device was increased by about 105%.

• ETRI Journal
• /
• v.29 no.4
• /
• pp.533-535
• /
• 2007

For the purpose of decreasing intermodulation distortion, a new multi-harmonic suppression band-pass filter based on a microstrip radial stub is studied. Compared with traditional resonator filters, the new filter can suppress the second, third, and even fourth harmonics directly. The dimension of the filter is about $0.3\;{\lambda}_{g^0}{\times}0.13\;{\lambda}_{g^0}$ (${\lambda}_{g^0}$ is the guiding wavelength at the resonant frequency). Only one gap was introduced, so lower insertion loss can be obtained. Basic agreement between the measured and simulated results has been achieved.