• Tribology and Lubricants
• /
• v.14 no.1
• /
• pp.79-84
• /
• 1998

This paper presents the experimental study of the dynamic internal pressure within a vane pump. The measurement of the dynamic internal pressure acting on the line contact between the vane and the camring in a vane pump with intravanes have been investigated. The variations of the radial acting force of a vane are calculated from previously measured results of dynamic internal pressure in four chambers surrounding a vane, and the variations of the film thickness are estimated in both the rotational speed ranges from 600 to 1200 rpm and the delivery pressure ranges from 1 to 14 MPa. The experimental technic has been established to obtain the data for performance analysis, such as reaction forces between vane and camring, friction wear at the contact regions, leakage characteristics and net forces upon the pump shaft in case of the unsteady load which is forced to the intravane pressure balance type vane pump.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.8
• /
• pp.213-220
• /
• 2003

By the localization of electro-chemical dissolution region, we succeeded in a few micrometer size hole drilling on stainless steel with the radial machining gap of about 1 ${\mu}{\textrm}{m}$. Tens of nanosecond duration voltage pulses were applied between WC micro-shaft and stainless steel in the 0.1 M $H_2SO_4$ solution. Pt balance electrode was used to drill the high aspect ratio micro-hole without generation of Cr oxide layer on the machined surface. The effects of applied voltage, pulse duration, and pulse period on localization distance were investigated according to machining time. We suggested the taper reduction technique especially brought up on blind-hole machining. High quality micro-holes with 8 ${\mu}m$ diameter with 20 ${\mu}m$ depth and 12 ${\mu}m$ diameter with 100 ${\mu}m$ depth were drilled on 304 stainless steel foil. The various hole shapes were also produced including stepped holes and taper free holes.

• Journal of Biosystems Engineering
• /
• v.33 no.2
• /
• pp.94-100
• /
• 2008

Present chemical application method using a power sprayer has been labor intensive, costly and ineffective. Therefore, a small agricultural unmanned helicopter was suggested to replace the conventional spray system. In this study, conceptual design for developing the helicopter and a consequential prototype were reported. The overall conceptual design was initiated by deciding the type of agricultural helicopter, as the single rotor helicopter with a tail system. As the first step of the designing, an air-cooled, 2-stroke engine was selected and a prototype transmission was designed by determining the rotating speed of main rotor shaft. A 'pusher' type tail rotor system was adapted to balance the reaction torque and reduce the power use. The tail boom length was designed to avoid the rotating trajectory of the main rotor. The RF console consisted of the engine control, attitude control, and emergency control modules. Assembling the prototype concluded the mechanical development of the agricultural helicopter.

• Journal of Korean Foot and Ankle Society
• /
• v.18 no.2
• /
• pp.43-47
• /
• 2014

Hallux valgus is a lateral deviation of the first phalanx and medial deviation of the first metatarsal at the first metatarsophalangeal (MP) joint. Its incidence has increased due to developing footwear. The etiologies include fashion footwear, genetic causes, anatomical abnormality around the foot, rheumatoid arthritis, and neuromuscular disorders. Physiologic alignment of the first MP joint is maintained by congruent and symmetric alignment of the articular surface of the first proximal phalanx and first metatarsal head, physiologic relationship of the distal first metatarsal articular surface and the first metatarsal shaft axis, and stable balance of soft tissue around the first MP joint and stable tarsometatarsal joint. Several factors have been associated with hallux valgus, including pes planus, hypermobility of the first tarsometatarsal joint, flattened shape of the first metatarsal head, increased distal metatarsal articular angle, and deformation of the medial capsular integrity. History and physical examination are very important to diagnosis of hallux valgus. Simple radiography provides information on deformity, particularly in weight-bearing anteroposterior and lateral radiographs. Understanding the etiologies and pathophysiology is very important for success in treatment of patients with hallux valgus.

• The KSFM Journal of Fluid Machinery
• /
• v.12 no.5
• /
• pp.47-53
• /
• 2009

A rotordynamic and detailed stability analysis in accordance with API 617 standard were performed with a turbo-compressor, which is one of key rotating machinery in refinery, petroleum, and power plants. The system is composed of rotor shaft, impeller, sleeve hub, balance drum, and coupling hub. The rotor system is supported by tilting pad bearings, which has 5 pads and pad on loading condition. The rotordynamic analysis specified by API 617 includes the critical speed map, mode shape analysis, Campbell diagram, unbalance response analysis, and stability analysis. In particular, the specifications of stability analysis consist of a Level 1 analysis that approximates the destabilizing effects of the labyrinth seals and aerodynamic excitations, and Level 2 analysis that includes a detailed labyrinth seal aerodynamic analysis. The results of a rotordynamic analysis and stability analysis can evaluate the operating compressor health and can be utilized as a guide of its maintenance, repair and trouble solution.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.211-216
• /
• 2001

The components with the circular cross section have the symmetric combination parts for rotating balance and the crack emanates from the symmetric combination parts. The symmetric cracks from symmetric combination parts make a decrease in the component fatigue life more than single crack. In this study, to estimate the behavior of symmetric cracks, the fatigue test was performed using rotary bending tester on the specimen with a symmetric defects in circular cross section. The material used in this study is Ni-Cr-Mo steel alloy. Under the same stress, the result from the rotary bending fatigue test turned out that the symmetric cracks made a decrease in the fatigue life by 35% more than single crack and the relation between log a and cycle ratio $N/N_f$ obtained linearly.

• Advances in aircraft and spacecraft science
• /
• v.5 no.3
• /
• pp.349-362
• /
• 2018

A non-linear numerical simulation technique for predicting the unsteady performances of an airbreathing engine is developed. The study focuses on the simulation of integrated propulsion systems, where a closer coupling is needed between the airframe and the engine dynamics. In fact, the solution of the fully unsteady flow governing equations, rather than a lumped volume gas dynamics discretization, is essential for modeling the coupling between aero-servoelastic modes and engine dynamics in highly integrated propulsion systems. This consideration holds for any propulsion system when a full separation between the fluid dynamic time-scale and engine transient cannot be appreciated, as in the case of flow instabilities (e.g., rotating stall, surge, inlet unstart), or in case of sudden external perturbations (e.g., gas ingestion). Simulations of the coupling between external and internal flow are performed. The flow around the nacelle and inside the engine ducts (i.e., air intakes, nozzles) is solved by CFD computations, whereas the flow evolution through compressor and turbine bladings is simulated by actuator disks. Shaft work balance and rotor dynamics are deduced from the estimated torque on each turbine/compressor blade row.

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.217-228
• /
• 2004

This paper presents the rotating test techniques and the results of the roating test of the small-scaled hingeless rotor system with composite paddle blades in hover and forward flight conditions. The small-scaled rotor system was designed using froude-scaled properties of full scale rotor system. Metal flexures and composite flexures were made as hub flexures by the same dynamic properties of rotor system. The rotating tests of hingeless rotor system installed in GSRTS at KARI were carried out to get lead-lag damping ratios and aerodynamic loads of the hingeless rotor system. MBA(Moving Block Analysis) technique was used for the estimation of lead-lag damping ratio. 6-components balance was installed between hub and main shaft and straingauges on blades were instrumented for the measurements of aerodynamic loads of rotor system. Tests were performed on the ground and in the wind tunnel according to the test conditions of hover and forward flight, respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.12
• /
• pp.2989-2994
• /
• 2000

A mechanical face seal is a tribo-element intended to control leakage of working fluid at the interface of a rotating shaft and its housing. Leakage of working fluid decreases drastically as the clearance between mating seal faces gets smaller. But the very small clearance may result in an increased reduction of seal life because of high wear and heat generation. Therefore, in the design of mechanical face seals a compromise between low leakage and acceptable seal life is important, ant it present a difficult and practical design problem. A fluid film or sealing dam geometry of the seal clearance affects seal lubrication performance very much, and thereby is optimization is one of the main design consideration. in this study the Reynolds equation for the sealing dam of mechanical face seals is numerically analyzed, using the Galerkin finite element method, which is readily applied to various seal geometries, to give lubrication performances, such as opening force, restoring moment, leakage, and axial and angular stiffness coefficients. Then, to improve the seal performance an optimization is performed, considering various design variables simultaneously. For the tested case the optimization ha successfully resulted in the optimal design values of outer and inner seal radii, coning, seal clearance, and balance radius while satisfying all the operation subjected constraints and design variable side-constraints, and improvements of axial and angular stiffness coefficients by 16.8% and 2.4% respectively and reduction of leakage by 38.4% have been achieved.

• Journal of the Korean Society of Costume
• /
• v.60 no.5
• /
• pp.117-127
• /
• 2010

In this study, hyperspace is a result of imagination created by means of facts and fiction, represents a transfer to determination and indetermination, and means an extension to an open form. In other words, hyperspace is a high dimensional space expanded to imagination through the combination of the viewpoint on facts in this dimension and fiction. When the 2D plane surface or 3D symmetry is destroyed, or when the frame is twisted or entangled, the non-Euclidean geometry is created eventually. And when the twisting leads to transmutation and the destruction of the form reaches the extreme; this in turn became the twisting like Mbius band. Likewise, the non-Euclidean geometry is co-related to the asymmetry of the Higgs mechanism. When the 'destruction of symmetry' is considered, symmetric theory and asymmetric world can be connected. The asymmetry in turn can maintain balance by arranging the uneven weights at different distances from the shaft. Moreover, at this the concept of the upper, lower, left and right, which was included in the original form, may be crumbled down. The destruction of the symmetry is essential in order to present forecast that coincides with the phenomenon of the real world. Non-Euclidean geometry characteristic is expressed by asymmetry, twists, and deconstruction and its representative characteristic is ambiguity. The boundary between the front, back, upper, lower, inner and outer is unclear, and it is difficult and vague to pinpoint specific location. The design that does not clearly define or determine the direction of wearing costume is indeed the non-oriented design that can be worn without getting restricted by specific direction such as front and back. Non-Euclidean geometry characteristic of hyperspace have been applied to create new shapes through the modification of the substance from traditional clothing of the eastern world to modern fashion. The way of thinking in the 'hyperspace' that used to be expressed in the costumes of the east and the west in the past became the forum for unlimited creation.