• 한국환경과학회지
• /
• 제24권12호
• /
• pp.1601-1608
• /
• 2015

This study evaluates heavy metal(Cu and Cr) adsorption characteristics produced from food waste charcoal extracted in an optimal operation condition after analyzing activated charcoal of iodine adsorption and heavy metals that derived from an activation process of carbide by the developed by-products of food waste treatment facility using the methods from previous studies. As experiment apparatus, this study used a tube-shaped high temp furnace. The mixing ratio of by-products of food waste treatment facility, carbide, and activation component($ZnCl_2$) was 1:1. The experiment was proceeded as adjusting the activation temperature from 400 to $800^{\circ}C$ and activation time from 30 to 120 minutes. The optimal activation condition for iodine absorption was 90 minutes at $700^{\circ}C$ and by using the produced food waste charcoal, this study conducted an experiment on absorption of heavy metals (Cu and Cr) as changing pH of artificial wastewater and stirring time. As a result, pH 7 showed the highest heavy metal decontamination ratio and in terms of stirring time, it revealed balance adsorption after 10 minutes. This result can be particularly applied as basic data for recyclability of high concentration organic waste, by-products of food waste treatment facility, as an food waste charcoal.

• 한국환경보건학회지
• /
• 제37권1호
• /
• pp.50-56
• /
• 2011

The adsorption capacity of charcoal is a function of the airborne concentration of the target chemical. To evaluate the adsorption capacity of charcoal packed in the cartridges of air purifying respirators, breakthrough tests were conducted with carbon tetrachloride for three commercial cartridges (3M models #7251, #6000 and AX) at 25, 50, 100, 250 and 500 ppm. Adsorption capacities were calculated using a mass transfer balance equation derived from the curve fitting to the breakthrough curves obtained experimentally. Carbon micropore volumes were estimated by iteration to fit the Dubinin/Radushkevich (D/R) adsorption isotherm. They were 0.6566, 0.5727 and 0.3087 g/cc for #7251, #6000 and the AX cartridge, respectively. Above 100 ppm (at high challenge concentrations), #7251 and #6000 showed higher adsorption capacities. However, as the challenge concentration decreased, the adsorption capacities of #7251 and #6000 sharply dropped. On the other hand, the adsorption capacity of the AX cartridge showed little change with the decrease of the challenge concentration. Thus, the AX showed a higher adsorption capacity than #7251 and #6000 at the 5-50 ppm level. It is concluded that service-life tests of cartridges and adsorption capacity tests of charcoal should be conducted at challenge concentration levels reflecting actual working environmental conditions. Alternatively, it is recommended to use the D/R adsorption isotherm to extrapolate adsorption capacity at low concentration levels from the high concentration levels at which breakthrough tests are conducted, at a minimum of two different concentration levels.

• 한국환경과학회지
• /
• 제29권10호
• /
• pp.969-979
• /
• 2020

A numerical simulation was conducted on perfluorooctane sulfonate (PFOS) in the Gwangyang Bay using a multi-box model to estimate the transport of organic chemicals in the coastal environment. The results of the sensitivity analysis on dissolved PFOS and PFOS in Particulate Organic Carbon (POC) indicate that they were most significantly influenced by the adsorption rate, desorption rate, and sinking velocity coefficients. PFOS in phytoplankton was found to be sensitive to bio-concentration and the excretion rate. The results of the mass balance indicate that the standing stocks of PFOS in water, POC, and phytoplankton are 345.55 g, 63.76 g, and 0.11 g, respectively, in the inner part and 149.90 g, 27.51 g, and 0.05 g, respectively, in the outer part. Considering flux in the inner part, adsorption to POC had the highest value among transition paths. The next highest were desorption, outflow to the outer part, and inflow to the inner part. Outflow into the open sea was found to have the highest value for the outer part.

• 한국수산과학회지
• /
• 제52권1호
• /
• pp.74-80
• /
• 2019

Nonylphenol is an endocrine-disrupting chemical that is the degradation product of the nonionic surfactants nonylphenol ethoxylates. To understand the contamination and behavioral characteristics of nonylphenol, we measured the nonylphenol concentrations in surface water in the lower reaches of the Suyeong River, Korea. The results were used to estimate the material balance. The target area was divided into three regions to estimate the material balance of nonylphenol. In region 1, in flux of the dissolved nonylphenol was 282.3 g/day and the nonylphenol influx in particulate suspended solids was 1,582.8 g/day. The dissolved nonylphenol outflow discharged toward region 2 was 192.5 g/day, while the adsorption to particulate suspended solids was 89.8 g/day. Within the particulate suspended solids, the outflow to region 2 was 1,250.0 g/day, while the estimated amount settling in the sediments was 422.7 g/day. The adsorption of dissolved nonylphenol to the particulate suspended solids in regions 1 and 2 was 31.8% and 54.9%, respectively. In region 3, the desorption rate was 8.8%.

• Archives of Pharmacal Research
• /
• 제3권2호
• /
• pp.65-74
• /
• 1980

Analysis of particle size distribution of a sample of fine aluminum hydroxide powder was carried out by four different methods, i. e., conductivity, air permeability, gas-adsorption and sedimentation. Each method was reproducible. The results obtained by Coulter counter and sedimentation balance were similar, and the data obtained by Lea and Nurse permeameter and Stroehlein areameter were also similar. But the results differ considerabley between the former and the latter. The advantages and disavantages of each method were discussed briefly and a means of comparing the results with those obtianed by surface area measurements was shown.

• 공업화학
• /
• 제18권4호
• /
• pp.337-343
• /
• 2007

천연가스의 누출을 감지하기 위해서 첨가되는 유기 황 화합물질인 부취제에 의해 연료전지 내의 스택 전극과 개질기 촉매들이 피독되어 시스템 성능저하의 큰 원인이 되고 있다. 본 연구에서는 실리카, 알루미나, 활성탄, HZSM-5, Ultra-stable Y 제올라이트(USY) 및 베타 제올라이트와 같은 흡착제들을 부취제 제거용 흡착제로 사용하여, tetra-hydrothiophene (THT)와 tert-butylmercaptan (TBM)에 대한 흡착 성능을 연속식 흡착시스템에서 얻은 흡착파과곡선을 비교하여 평가하였다. 제올 라이트의 Si/Al 비, 흡착온도 및 Balance Gas (메탄, 헬륨) 종류의 변화가 흡착성능에 미치는 영향을 조사하고, THT와 TBM의 경쟁적인 흡착특성을 비교하였다. 여러 흡착제 중에서 H형, beta-zeolite (BEA)가 부취제인 TBM과 THT에 대해서 가장 우수한 흡착능력을 나타내었으며, 동일한 흡착제 상에서는 THT가 TBM보다 많은 양으로 흡착제거되었다. Temperature Programmed Desorption (TPD) 및 Infrared 스팩트럼(IR) 분석결과 부취제 황화합물은 제올라이트 표면에서 물리흡착과 더불어 산점에 의한 화학흡착을 이루는 것을 확인하였다.

• Carbon letters
• /
• 제3권4호
• /
• pp.187-191
• /
• 2002

In the present research, we prepared the activated carbon (AC) sorbents to remove gas-phase mercury. The mercury adsorption of virgin AC, chemically treated AC and fly ash was performed. Sulfur impregnated and sulfuric acid impregnated ACs were used as the chemically treated ACs. A simulated flue gas was made of SOx, NOx and mercury vapor in nitrogen balance. A reduced mercury adsorption capacity was obtained with the simulated gas as compared with that containing only mercury vapor in nitrogen. With the simulated gas, the sulfuric acid treated AC showed the highest performance, but it might have the problem of corrosion due to the emission of sulfuric acid. It was also found that the high sulfur impregnated AC also released a portion of sulfur at $140^{\circ}C$. Thus, it was concluded that the low sulfur impregnated AC was suitable for the treatment of flue gas in terms of stability and efficiency.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2012년도 춘계학술발표대회 논문집
• /
• pp.364-369
• /
• 2012

The development of solar thermal energy used adsorption desalination technology have been examined as a viable option for supplying clean energy. In this study, the modelling of the main devices for solar thermal energy used and adsorption desalination system was introduced. Silica gel type adsorption desalination system is considered to be a promising low-temperature heat utilization system. The design is divided into three parts. First, the evaporator for the vaporization of the tap water is designed, and then the reactor for the adsorption and release of the steam is designed, followed by the condenser for the condensation of the fresh water is designed. In addition, new features based on the energy balance are also included to design absorption desalination system. In this basic research, One-bed(reactor) adsorption desalination plant that employ a low-temperature solar thermal energy was proposed and experimentally studied. The specific water yield is measured experimentally with respect to the time controlling parameters such as heat source temperatures, coolant temperatures, system switching and half-cycle operational times. Desalination is processes that permeate our daily lives, but It requires substantial energy input, powered either from electricity or from thermal input. From the environmental and sustainability perspecives, innovative thermodynamic cycles are needed to produce the above-mentioned useful effects at a lower specific energy input. This article describes the development of adsorption cycles for the production of desalting effects. We want that this adsorption system can be driven by low temperature heat sources at 60 to $80^{\circ}C$, such as renewable, solar thermal energy.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.808-811
• /
• 1996

A mathematical model was developed for the simulation of a Pressure Swing Adsorption process with dehydrogenation reaction. The minimum number of beds and optimum operating sequence were determined using MINLP under the given operating conditions. Based on these results, we estimated the minimum annual cost.

• Korean Chemical Engineering Research
• /
• 제48권6호
• /
• pp.768-775
• /
• 2010

제올라이트(faujasite) 흡착제가 충진된 흡착탑에서 에탄/에틸렌 혼합가스의 흡착 동특성과 탈착제로 프로판을 이용한 치환탈착 시의 동특성을 실험 및 이론적으로 연구하였다. 물질수지와 에너지수지를 고려하고 다성분 흡착평형으로 이상흡착상 모델을 적용한 전산모사는 흡탈착 파과곡선 실험 결과를 잘 예측하였다. 흡착파과 시 에탄의 롤-엎은 흡착압력이 높고, 온도가 낮을수록 증가하였다. 에탄/에틸렌 혼합가스로 포화된 흡착탑으로 탈착제인 프로판을 주입하여 치환탈착할 때 탈착단계의 일정 시간 동안에 거의 100%에 가까운 에틸렌을 얻을 수 있었다. 탈착제의 흡착세기는 에틸렌의 탈착 및 재흡착 시에 큰 영향을 미치는 것으로 나타났다. 프로판 대신 흡착세기가 강한 이소부탄을 탈착제로 사용한 경우에 탈착단계 후 재흡착에서 에틸렌 흡착용량이 많이 감소하는 현상이 관찰되었다. 전산모사를 통하여 ${(q_s{\times}b)}_{C_2H_4}/{(q_s{\times}b)}_{C_3H_s}$의 비율이 0.83일 때, 즉 탈착제와 에틸렌이 거의 유사한 정도의 흡착세기를 가질 때 치환탈착공정의 성능이 우수하였다.