• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.5
• /
• pp.124-133
• /
• 1994

Many of non-contact measuring systems are used to estimate surface characteristics owing to their advantages of high speed and undanaged test. In this paper, a new measuring system is proposed to acquire image from CCD camera through back light illumination. Lowpass filter is very useful in view of noise removal and optimum binary image can be made through histogram equalization which is one of the histogram technique to maximize brightness intensity between workpiece and background. Laplacian operator is used to detect workpiece edge from binary image. In case of image treatment applying Laplacian operator, surface roughness is calculated by introducing conversion coefficient for coordinate of pixel which edge is composed of. In summary, the work is concerned with the development of a new technique for roughness measurement by the image processing in turning.

• Korean Journal of Applied Biomechanics
• /
• v.13 no.3
• /
• pp.15-26
• /
• 2003

This study was conducted to investigate the performance times, CM position and CM speed, pole chord length and pole chord angle, whole body angular momentum(X axis), and grip width in pole vault event according to the event and phase; touch down, pole plant, take-off, maximum pole bending pole straight, pole release, peak height, and foot contact, pole contact, free flight. The pole vaulting of four male elite vaulters including six trial were filmed using two video digital cameras at 60 Hz at 56th national athletic match, and data were collected through the DLT method of three dimensional cinematography. In general the better jumper is, the longer the performance time is. And the greater CM speed is, and the better his transformation ability of CM horizontal speed into vertical speed is. As he uses a longer pole, his grip is higher, and it is a enough for him to rock back his body, so that he pulls and pushes the pole well keeping his hips close to. An greater maximum angular momentum and early positioning of the hips parallel to the bar makes his body far side of the bar and his bar clearance easier. Specially our national jumper needs to have more powerful braking force during foot contact phase, and take his body on the pole after maximum pole bending, and pull and push the pole strongly keeping his hips close to. Also he needs to have stronger muscular strength in order to control the longer pole and use the pole of proper tension more efficiently.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.402-402
• /
• 2011

본 연구에서는 결정질 태양전지 제작에 있어 재료비 절감과 기존의 Screen Printing 공정 기술에서의 단점을 보완하기 위한 방안으로 후면 passivation 구조와 레이저를 이용한 국부적 후면 전극 형성(Laser Fired Contact) 방법에 대한 실험을 진행하였다. 후면 passivation 층으로 SiO2/ SiNx/SiO2 삼중막 구조와 SiNx 단일막 구조를 형성시킨 후 anneal 온도에 따른 소수캐리어의 lifetime 변화를 비교하였다. LFC 형성은 2 ${\mu}m$ 두께의 Al이 증착된 기판 후면에 1,064 nm 파장의 레이저를 통해 diameter와 dot pitch 등의 파라미터를 가변 하여 실시하였다. 실험 결과 800$^{\circ}C$의 고온 열처리 후 ONO 삼중막에서의 lifetime 향상이 우세하여 SiNx 단일 막 보다 열적 안정성이 우수함을 확인하였다. LFC 결과 diameter가 40, 50, 60 ${\mu}m$로 가변된 조건에서는 40 ${\mu}m$ 일 경우와 dot pitch가 200, 500, 1,000 ${\mu}m$로 가변된 조건에서는 1,000 ${\mu}m$일 경우 610 mV의 Voc 값을 보였다. 이는 레이저를 통해 국부적으로 Al-Si 간 alloy를 형성시킴으로써 접촉 면적이 최소화됨에 따라 후면에서의 캐리어의 재결합속도를 감소시키고, passivation 효과를 극대화시키기 때문이다.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.1
• /
• pp.41-52
• /
• 2007

The present study analyzed the two hand backhand stroke motion of six female high school tennis players who won the championship at the National Athletic Meeting in 2006, and drew conclusions as follows. The open angle of the racket at the moment of impact was 90 degree without significant difference among the players, making a wide contact between the ball and the racket. The racket angle was 43 degree at take back and 91 at impact, showing a style of holding the racket rather upright in general. In back swing from the top to the impact, the shoulders and the hips turned by 97 degree and 40 degree, respectively. At the moment of impact, the height of the impact was 54%H, and the position of the impact was 10%H ahead of and 37%H left from the central axis of the body. The right hand made a continental grip and the left hand made a Western or semi Western grip. Through the entire swing motion, the grip angle of the left hand was smaller than that of the right hand, and those who maintained a large grip angle of the right hand at the moment of take back put the racket head slightly farther from the body. In the swing of the racket head from the lowest point to the impact, the vertical length of movement was 11%H and the horizontal length of movement was 60%H, quite long.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.18 no.1
• /
• pp.50-58
• /
• 2009

For precise tracking control of a servo system with nonlinear friction, a robust friction compensation scheme is presented in this paper. The nonlinear friction is difficult to identify the friction parameters exactly through experiments. Friction parameters can be also varied according to contact conditions such as the variation of temperature and lubrication. Thus, in order to overcome these problems and obtain the desired position tracking performance, a robust adaptive back-stepping control scheme with a dual friction observer is developed. In addition, to estimate lumped friction uncertainty due to modeling errors, a DEKF recurrent neural network and adaptive reconstructed error estimator are also developed. The feasibility of the proposed control scheme is verified through the experiment fur a ball-screw system.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.36T no.1
• /
• pp.51-57
• /
• 1999

This thesis is written about the Wired Logic Type Unit in developing equipment that the load is driven, that the interface unit connect with 1 Scan time to PO30 of operated PLC output contact with that a sensing signal of Temperature Sensor RSD Pt $100\Omega$ let generate the relay output of temperature controller and input the PLC. The PLC Test Kit in country that the PLC to be programmed at the PLC education place is able to drive the load, is done to do a education of PLC on status that interface process between PLC and load are disregarded. As Developing Kit for supplement this point, when the relay output of temperature controller to use Pt 100 of temperature sensor as mentioned on the former among every kinds of sensor feed back to the input of the PLC, as the equipment to act with real time system that the output contact of PLC operated to insert the WLTIJ among PC, PLC and the load, it can understand and see very easy the main principle of PLC use. The structure of WLTU to be a interface unit of load separated as to the point of contact and noncontact, sensor, indicating lamp and A contact and B contact that is belong to driving part, and a motor is belong to loading part.

• Journal of Korean Society for Atmospheric Environment
• /
• v.15 no.E
• /
• pp.17-28
• /
• 1999

Gas-liquid contact tests above a perforated-plate were conducted with air and water at flooding gas-flow conditions in order to study two-phase flow characteristics in a limestone-gypsum SO2 absorber. Gas layers were in the form of air pockets and confined to the limited areas around each duct pipe, while the remaining tary area were in the wet condition. The liquid above the tray was always in the flooded and even fluidized conditions at gas flows over the range studied, although vigorous bubbly or churn-turbulent two-phase regime was only observed in the immediate vicinity of the gas hole exit at low gas loads. The froth zone was extremely active to provide intimate contact between gas and liquid so that the necessary mass transfer operation can take place, which is the primary purpose of high-performance SO2 absorbers. Howefer, the absorber $\Delta$P was 250mmH2O for the initial water level at 150mm, which is an important issue to be resolved for economical operation of the SO2 absorber. It was seen in the liquid level-and gas flow-transient tests that changes in the absorber liquid inventory were much more pronounced for intimate gas-liquid contact than changes in the gas flow. Based on the 4- and 8-duct pipe test results, grouping the duct pipes near the center of the test tray seemed to promote better recirulation of liquid from gas-liquid contact zone back to the reaction tank so that the absorbed SO2 can be neutralized.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.33 no.6
• /
• pp.341-348
• /
• 2019

The purpose of this study was to investigate the efficacy of Torreyae semen extract against antimicrobial and allergic contact dermatitis to explore its utility as a herbal resource. To this end, the antibacterial effects of Torreyae Semend extracted with hot water and ethanol (30%, 60%, 90%) were investigated using Staphylococcus aureus, Staphylococcus epidermidis, pseudomonas aeruginosa, and Propionibacterium acnes. And observed the anti-atopic dermatitis efficacy with a mouse model that allergic contact dermatitis induced by DNCB. Experimental results showed that the antibacterial activity against S. epidermidis and P. aeruginosa was significantly higher in the hot water extract of Torreyae Semen. We observed that the extracts of 30% ethanol and hot water of Torreyae Semen inhibited growth in a concentration-dependent manner in P. acnes & S. epidermidis. We observed that the administration of hot water extracts and 30% ethanol extract of Torreyae Semen significantly reduce the thickness of ear & back and gross skin condition compared to the control group in the mice with allergic contact dermatitis. As a result of H & E histological staining, it was observed that the Torreyae Semen extraction group had markedly reduced epidermis and skin thickness, granules, and keratinization compared to the control group. The groups administrated with Torreyae Semen hot water extracts had decreased TNF-α and IL-10 contents compared with the control group. As a result, Torreyae Semen may be used as a useful herbal resource because it has a certain level of antibacterial and anti-atopic effects.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.3
• /
• pp.359-366
• /
• 2007

Slow sand filtrations have been widely used for water treatment in small communities, however their capacity is often limited by high turbidity in the raw water. For this reason, several pre-treatment facilities were required for a slow sand filter. Turbidity removal from the highly turbid raw water was investigated in roughing filters as a pre-treatment process. The roughing filters followed by rapid mixing tank were operated in the form of a contact filtration. In several jar tests, the predetermined optimum aluminium sulfate (alum) doses for turbid water of 30 and 120NTU were 30 and 50mg/L, respectively. At the optimum alum dose, physically optimum parameters including G value of $220sec^{-1}$ and rapid mixing time of 3 minutes were applied to the contact filtration system. Without addition of alum, the filtrate turbidity from the roughing filters, packed respectively with different media such as sand, porous diatomite ball and gravel, was in the range of 5~30NTU at filtration velocities of 30 and 50m/day. However, the application of a contact filtration to roughing filters showed stably lower filtrate turbidity below 1.0NTU at filtration velocity of 30 m/day. Although the filtration velocity increased to 50m/day, filtrate turbidity was still below 1.0NTU in both single and double layer roughing filters. At influent turbidity of 120NTU, the filtrate turbidity was over 5 NTU in the triple layer roughing filter, which shortened the filter run time. The flocs larger than $10{\mu}m$, formed in the rapid mixing tank, were almost captured through the roughing filter bed, while the almost flocs smaller than $10{\mu}m$ remained in filtrate.

• The Journal of Korea Robotics Society
• /
• v.7 no.3
• /
• pp.171-181
• /
• 2012

Outdoor mobile robots are faced with various terrain types having different characteristics. To run safely and carry out the mission, mobile robot should recognize terrain types, physical and geometric characteristics and so on. It is essential to control appropriate motion for each terrain characteristics. One way to determine the terrain types is to use non-contact sensor data such as vision and laser sensor. Another way is to use contact sensor data such as slope of body, vibration and current of motor that are reaction data from the ground to the tire. In this paper, we presented experimental results on terrain classification using contact sensor data. We made a mobile robot for collecting contact sensor data and collected data from four terrains we chose for experimental terrains. Through analysis of the collecting data, we suggested a new method of terrain feature extraction considering physical characteristics and confirmed that the proposed method can classify the four terrains that we chose for experimental terrains. We can also be confirmed that terrain feature extraction method using Fast Fourier Transform (FFT) typically used in previous studies and the proposed method have similar classification performance through back propagation learning algorithm. However, both methods differ in the amount of data including terrain feature information. So we defined an index determined by the amount of terrain feature information and classification error rate. And the index can evaluate classification efficiency. We compared the results of each method through the index. The comparison showed that our method is more efficient than the existing method.