• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.806-813
• /
• 2008

In this research, mainly research about the structural and functional stability of sea dyke with variation of seepage condition after final closure. The piezometric head (water head in embankment) monitoring system was installed at two representative final closure section. The dredged fine sand filling condition was evaluated by in-situ test results. Also, the numerical analysis was performed to determine the permeability of bottom protection layer filled with dredged fine sand by monitoring results. According to numerical back analysis results, the coefficient of permeability of bottom protection section of is $7.6{\times}10^{-6}$ m/sec. These results are noted that the bottom protection layer of sea dyke was strong and intensively filled with dredged sand. Also, based on the seepage analysis, the seepage flux of this sea dyke was calculated about $2.42m^3$/day/m which is 29% decreased value compare with adjacent sea dyke.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1998.05a
• /
• pp.371-376
• /
• 1998

This paper describes an approach to a speed estimation method to remove speed sensor of underwater robot's AC drive systems. AC motors have been widely used in the field of underwater robot's manipulator or propulsion system. Most of these AC motors for underwater use have usually filled oil to compensate the high pressure in deep-sea operation, where a resolver is adopted to feed back the speed of rotor But this kind of speed feedback devices gives rise to some defects arising from their mechanical complexity and numerous signal lines; a resolver needs 6 or 7 signal lines for proper operation. This paper presents a speed estimation method to improve these problems of induction motor, which is adopted as a prototype of AC motor. The proposed speed estimation method is based on the RFO(rotor flux orientation) vector control method of voltage-fed AC drives. Using the controller of voltage-fed AC drives, it is unnecessary to measure the voltage for the estimation of rotor speed, which reduces the effects of measurement error Numerical simulation is carried out to investigate the validity of the method and the effects of rotors resistance variation.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.477-482
• /
• 2006

In this study, a micro vapor compressor has been designed, fabricated and tested. The micro vapor compressor was made of silicon substrates and fabricated by micromachining process. The compressor is driven by a piezoelectric actuator which is widely used in microfluidic systems because of its strong force and rapid response. The actuator is a bimorph structure which consists of a silicon membrane and a piezoelectric ceramic film. A simulation work was conducted on the performance characteristics of the compressor. The simulation investigated the flow rate variation under various back pressure conditions. Experimental works were carried out on the operation of a compressor and the test results were compared with the simulation results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.1
• /
• pp.43-49
• /
• 2009

A catalyzed diesel particulate filter (CDPF) causes the progressive increase in back pressure of an exhaust system due to the loading of soot particles. To minimize pressure drop which is generated by CDPF, the filter should be regenerated when it collects a certain quantity of soot. It is important to know characteristics of regeneration of CDPF with various of exhaust gas temperatures and compositions. The oxidation of HC in DOC leads to increase gas temperature of DOC downstream. The increased gas temperature by DOC has an positive effect on CDPF regeneration. This study presents characteristics of regeneration of CDPF with DOC according to various gas composition, such as HC and $O_2$ concentration. The test-rig is used to control each gas composition and temperature during regeneration of CDPF. Experimental results indicate that the increased concentration of $O_2$ regenerates DPF more actively. With increasing HC concentration, the gas temperature of CDPF upstream increased due to more oxidation of HC. But excessive supply of HC leads to decrease of $O_2$ concentration in the CDPF, which makes it hard to regenerate CDPF.

• Journal of Fashion Business
• /
• v.5 no.2
• /
• pp.49-65
• /
• 2001

This thesis aims to reveal the unsatisfactory unfitting factors in the tight collars of adult males' dress shirts for the purpose of improving neck-collar fitness. For this study, nine adult males were chosen as the subjects. When the subjects erected their necks upright, the researcher conducted an experiment, using the direct anthropometrical measuring method and the gypsum method by turns, in order to understand neck shapes by way of right-neck lateral flection, left-neck lateral flection, neck flection, neck extension, right neck rotation, and left neck rotation. And then, the propriety of allowances from body surface alteration was verified by analyses through the measurement of wearing comfortableness and clothing pressure in two sorts of ready-made dress shirts, which had different allowances. The consequences of this study are as follows: 1. In length alteration to movement, a decrease was found in the opposite (and an increase in the identical) directions of right-neck lateral flection, left-neck lateral flection, and neck flection movements. Also, when the subjects shook their heads, an increase was seen by 0.42$\sim$0.63cm in neck girth, 0.31$\sim$1.12cm in 3cm-above-the-neck base girth, and 1.16cm in neck extension of 3cm-above-the-neck base girth. 2. As a result of the drafts of surface measurement, the alteration ratios of dimensions and vertical length dropped in the identical directions of the movement, but grew in the opposite directions. A reverse change was shown in horizontal length. The rough widening gaps for making drafts were 0.7cm in front left and right, and 0.2cm in back left and right of 3cm-above-the-neck base girth. On the whole, the space was about 1.8cm, while there was no significant variation between the upright stationary test and the movement test. 3. There were important differences between the two kinds of ready-made dress shirts (Type A: 1cm allowance in neck girth; Type B: 2cm allowance) in clothing pressure and wearing comfortableness. That is, Type A had higher pressure and more uncomfortable sense of wearing. In other words, as clothing pressure and wearing comfortableness are negatively related to each other, Type A's greater clothing pressure led to worse wearing comfortableness.

• Membrane Journal
• /
• v.22 no.5
• /
• pp.332-341
• /
• 2012

We studied the effects of induction of natural convection instability flow (NCIF) according to the gravitational orientation (inclined angle) of the membrane cell on the reduction of membrane fouling in the constant-flow ultrafiltration (UF) of colloidal silica solutions. Five colloidal silica solutions with different silica size (average size = 7, 12, 22, 50 nm and 78 nm) were used as UF test solutions. The silica particles in colloidal solutions form cakes on the membrane surface thereby causing severe membrane fouling. The constant-flow UF performance according to the gravitational orientation of the membrane cell (from $0^{\circ}$ to $180^{\circ}$ inclined angle), was examined in an unstirred dead-end cell. We evaluate the effects of NCIF on the suppression of fouling formation by measuring the variation of transmembrane pressure (TMP) and the increase of critical flux by using the flux-stepping method. In the constant-flow dead-end UF for the smaller size (7, 12 nm and 22 nm) silica colloidal solutions, changing the gravitational orientation (inclined angle) of the membrane cell above the $30^{\circ}$ angle induces NCIF in the membrane module. This induced NCIF enhances back transport of the deposited silica solutes away from the membrane surface, therefore gives for the reduction of TMP. But in the constant-flow UF for the more larger size (50 nm and 78 nm) silica colloidal solutions, NCIF effects are not appearing. The critical flux is increased as increasing the module angle and decreasing the silica size. Those results show that the intesity of NCIF occurrence in membrane module is more higher as increasing the module angle and decreasing the silica size.

• Journal of Korean Society for Atmospheric Environment
• /
• v.28 no.2
• /
• pp.142-158
• /
• 2012

This paper investigates the physical and chemical characteristics of long-range transport (LRT) process of air pollutants by employing the MM5-CMAQ and its comparison with local emission dominant (LED) case over northeast Asia. We first classified high air pollution days into LRT and LED cases based on the synoptic meteorological variables of vorticity and geostrophic wind speed/direction at a geopotential level of over 850hPa. LRT cases are further categorized into three types of transport patterns (LRT-I-III) according to the air mass pathways from source regions. LRT-I-III are originated from northern, central, and southern China, respectively, identified by back trajectory analysis. Three LRT-I-III groups have different and unique locations of high pressure and transport pathways. The chemical characteristics showed that the simulated spatial distributions varied in terms of locations of maximum concentrations and the temporal variation of surface concentrations. The primary air pollutants such as $NO_x$, $PM_{10}$ and $SO_2$ of all of three LRT cases are well transported into Korea peninsula with different concentration levels. Of LRT cases, LRT-II has the greatest effect on air quality of Korea peninsula, followed by LRT-I and LRT-III. In comparison with LRT, the LED case shows relatively higher air pollution concentrations in general, but showed a variety of different air quality levels following the emission strength pattern. These widely varying patterns are impling the case dependent multi-directional approach for the development of indicators of long-range transport process over northeast Asia.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.107-121
• /
• 2003

When the seismic stability of quay walls is analyzed, the magnitudes of force components acting on quay walls during earthquakes and the phase relations among these force components must be properly evaluated. In general, force components include inertia force of the quay wall, lateral earth force, and water force. The magnitude and the phase relation of each force component vary according to the magnitude of the excess pore pressures developed in backfill soils of the quay wall. The dynamic thrust mobilized at the contact surface between the backfill soil and the wall develops as a result of the interactions among these force components. We propose a simple model to evaluate the magnitude and phase variation of the dynamic thrust on the back of the wall in terms of the excess pore pressure. The proposed model can predict the dynamic thrust by summing the magnitudes of farce components calculated from design equations for seismic pressures on the wall. The proposed model was verified by comparing its results with the results from a series of shaking table tests.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.9
• /
• pp.31-45
• /
• 2012

This study was conducted to estimate the stability of a quay wall in case of wave overtopping under the combined action of an earthquake and tsunami using limit equilibrium method. The tsunami force was calculated by using a numerical program called TWOPM-3D (3-D one-field Model for immiscible TWO-Phase flows). Especially, the wave force acting behind the quay wall after a tsunami wave overtopping was estimated by treating back fill as a permeable material. The stability of the quay wall was assessed for both the sliding and overturning modes under passive and active conditions. The variation in the stability of the quay wall with time was determined by parametric studies, including those for the tsunami wave height, seismic acceleration coefficient, internal friction angle of the soil, wall friction angle, and pore water pressure ratio. When the earthquake and tsunami were considered simultaneously, the tsunami induced wave overtopping increased the stability of the quay wall under the passive condition, but in the active condition, the safety factors decreased.

• Preventive Nutrition and Food Science
• /
• v.14 no.3
• /
• pp.240-245
• /
• 2009

High-performance liquid chromatography (HPLC) was applied to determine the carotenoid composition of carrots during storage and cooking. Analyses were conducted immediately after harvest and 1, 2, 4, and 8 weeks after harvest. During the course of the storage, the carotenoid levels generally decreased, and this decrease was found to be greater during the first week for $\beta$-carotene (all-trans-$\beta$-carotene) and lutein, and during the second week for $\alpha$-carotene. Additionally, the amount of the $\alpha-$ and $\beta$-carotenes in carrot leaves changed slightly within the first 2 weeks of harvest when stored at $4^{\circ}C$. Specifically, the level of lutein, the main component of carrot leaves, increased from 233.8$\pm$11.7 to $346.2\pm26.7{\mu}g$/g DW during the first 2 weeks. In addition, the change in carotenoid contents was observed during the home-processing of one Korean cultivar. Carrots fried in oil showed the highest amount of $\beta$-carotene ($164.3\pm6.6{\mu}g$/g DW) and $\alpha$-carotene ($50.1\pm0.4{\mu}g$/g DW), while carrots that were prepared by sauteing, pressure-cooking in water and microwaving had the second highest levels. The greatest loss of in carotenoids occurred in response to boiling in water containing 1% NaCl, braising and baking. The content of lutein increased slightly after boiling in water containing 1% NaCl ($9.3\pm0.4{\mu}g$/g DW), while a loss in lutein occurred after preparation using other home-processing methods. A cis-isomer of all-trans-$\beta$-carotene, 13-cis-$\beta$-carotene, was present in detectable amounts in all processed samples, but not in raw roots. Another isomer, 9-cis-$\beta$-carotene, was detected in carrots that were prepared by boiling, frying and pressure-cooking.