• Journal of Sensor Science and Technology
• /
• v.9 no.1
• /
• pp.83-89
• /
• 2000

BST thin films were deposited on the ITO coated glass for using TFELD insulating layer by rf magnetron sputtering method. $O_2/(Ar+O_2)$ mixing ratio was 10%, substrate temperature was changed from R.T. to $500^{\circ}C$, and working pressure was changed from 5 mTorr to 30 mTorr. BST thin films deposited with various conditions were investigated electrical, optical, structural properties, and stoichiometry. The result of investigation was achieved good fabrication condition that substrate temperature of $400^{\circ}C$, and working pressure of 30 mTorr. Relative dielectric constant of 254 at 1 kHz, leakage current density was below $3.3{\times}10^{-7\;}A/cm^2$ at 5\;MV/cm applied electric field, and transmittance was over 82% at visible range.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.2
• /
• pp.67-71
• /
• 2006

In this paper, we have investigated the structure and dielectric properties of the $(Ba_{0.6}Sr_{0.4})TiO_3$ (BST) thin films fabricated on MgO(100)/Si substrate by an alkoxide-based sol-gel method. Both the structure and morphology of those films were analyzed by x-ray diffraction (XRD) and atomic force microscope (AFM). For the MgO(100)/Si substrate, the BST thin films exhibited highly (100) orientation. The highly (100)-oriented BST thin films showed high dielectric constant, tunability, and figure of merit (FOM). The dielectric constant, dielectric loss and tunability of the BST thin films annealed at $700^{\circ}C$ deposited on the MgO(100)/Si substrate measured at 10 kHz were 515.9, 0.0082, and 54.3%, respectively.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.3
• /
• pp.391-395
• /
• 2007

MgO enhanced $(Ba_{0.6}Sr_{0.4})$ $TiO_3$ thick films have been fabricated by a tape casting and firing method for tunable devices on the microwave frequency band. In order to improve ferroelectric properties, the composite thick films enhanced with MgO on BST have been asymmetrically annealed by a focused halogen beam method. Dielectric constants of composite thick films are changed from 1050 to 1300 at 100 kHz after 60 s and 150 s annealing by the focused halogen beam. Even though no prominent changes were previously observed from the thick films before and after annealing in terms of chemical composition and surface morphology, it is clear that the average particle size of the thick films calculated by Scherrer's formula were increased by annealing. Furthermore, a strong correlation between particle size and dielectric constant of the composite thick films has been observed; dielectric constant increases with increased particle size. This has been attributed to the increased volume of ferroelectric domain due to increased particle sizes. As a result, the tuning range was improved by halogen beam annealing.

• Journal of the Korean Ceramic Society
• /
• v.35 no.9
• /
• pp.895-898
• /
• 1998

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.11a
• /
• pp.45-48
• /
• 2000

High dielectric (Ba,Sr)TiO$_3$thin films were etched in an inductively coupled plasma (ICP) as a function of C1$_2$/Ar gas mixing ratio. Under Cl$_2$(20)/Ar(80), the maximum etch rate of the BST films was 400$\AA$/min and selectivities of BST to Pt and PR were obtained 0.4 and 0.2, respectively. We investigated the etched surface of BST by x-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and x-ray diffraction (XRD). From the result of XPS analysis, we found that residues of Ba-Cl and Ti-Cl bonds remained on the surface of the etched BST for high boiling point. The surface roughness decreased as Cl$_2$increases in C1$_2$/Ar plasma because of non-volatile etching products. This changed the nature of the crystallinity of BST. From the result of XRD analysis, the crystallinity of etched BST film maintained as similar to as-deposited BST under Ar only and Cl$_2$(20)/Ar(80). However, (100) orientation intensity of etched BST film abruptly decreased at Cl$_2$only plasma. It was caused that Cl compounds were redeposited on the etched BST surface and damaged to crystallinity of BST film during the etch process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.45-48
• /
• 2000

High dielectric (Ba,Sr)TiO$_3$ thin films were etched in an inductively coupled plasma (ICP) as a function of C1$_2$/Ar gas mixing ratio. Under Cl$_2$(20)/Ar(80), the maximum etch rate of the BST films was 400$\AA$/min and selectivities of BST to Pt and PR were obtained 0.4 and 0.2, respectively. We investigated the etched surface of BST by x-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and x-ray diffraction (XRD). From the result of XPS analysis, we found that residues of Ba-Cl and Ti-Cl bonds remained on the surface of the etched BST for high boiling point. The surface roughness decreased as Cl$_2$ increases in Cl$_2$/Ar plasma because of non-volatile etching products. This changed the nature of the crystallinity of BST. From the result of XRD analysis, the crystalliility of etched BST film maintained as similar to as-deposited BST under Ar only and Cl$_2$(20)/Ar(80). However, (100) orientation intensity of etched BST film abruptly decreased at Cl$_2$ only plasma. It was caused that Cl compounds were redeposited on the etched BST surface and damaged to crystallinity of BST film during the etch process.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2006.05a
• /
• pp.29.1-29.1
• /
• 2006

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1411-1413
• /
• 2001

The $(Ba_{0.5}Sr_{0.5})(Nb_{0.5}Ti_{0.5})O_3$ [BSNT] ceramics were prepared by conventional mixed oxide method. The structural properties of the BSNT ceramics with sintering temperature were investigated by XRD, SEM, EDS. Increasing the sintering temperature, diffraction intensity of the BST(110) peak was increased. The average grain size of BSNT ceramics were increased with sintering temperature. In the case of BSNT ceramics sintered at 1550$^{\circ}C$, the grain was uniform and the pore was not existed. Increasing the sintering temperature from 1400$^{\circ}C$ to 1500$^{\circ}C$, the amount of Nb and Sr were decreased. The density of BSNT ceramics sintered at 1550$^{\circ}C$ was $1.125g/cm^2$.

• Journal of the Korean Ceramic Society
• /
• v.43 no.11 s.294
• /
• pp.715-723
• /
• 2006

Perovskite oxide materials are very important for the electronics industry, because they exhibit promising properties. With an interest in the obvious applications, significant effort has been invested in the growth of highly crystalline epitaxial perovskite oxide thin films in our laboratory. And the desired structure of films was formed to achieve excellent properties. $Y_1Ba_2Cu_3O_{7-x}$ (YBCO) superconducting thin films were simultaneously deposited on both sides of 3 inch wafer by inverted cylindrical sputtering. Values of microwave surface resistance R$_2$ (75 K, 145 GHz, 0 T) smaller than 100 m$\Omega$ were reached over the whole area of YBCO thin films by pre-seeded a self-template layer. For implementation of voltage tunable high-quality varactor, A tri-layer structured SrTiO$_3$ (STO) thin films with different tetragonal distortion degree was prepared in order to simultaneously achieve a large relative capacitance change and a small dielectric loss. Highly a-axis textured $Ba_{0.65}Sr_{0.35}TiO_3$ (BST65/35) thin films was grown on Pt/Ti/SiO$_2$/Si substrate for monolithic bolometers by introducing $Ba_{0.65}Sr_{0.35}RuO_3$ (BSR65/35) thin films as buffer layer. With the buffer layer, the leakage current density of BST65/35 thin films were greatly reduced, and the pyroelectric coefficient of $7.6\times10_{-7}$ C $cm^{-2}$ $K^{-1}$ was achieved at 6 V/$\mu$m bias and room temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.303-304
• /
• 2005

Add $Li_2CO_3$ to $(Ba_{0.6}Sr_{0.4})$ $TiO_3$ powder to lower sitering temperature in this research, made thick film by tape casting method. Investigated about sitering temperature and physical properties that added $Li_2CO_3$ Even if lower sitering temperature about $200^{\circ}C$ adding $Li_2CO_3$ 10wt.%, density was near to 5.7$g/cm^3$ that is theoretical values, and crystal structure examined as perobeuseukaiteu senior after sintering.