• Tribology and Lubricants
• /
• v.25 no.5
• /
• pp.330-334
• /
• 2009

Hydraulic servo cylinders have been used to control accurately a large machine in power plant. Especially, Piston head and bush of servo cylinder is assembled sleeve and piston head and bush made of Cu alloy and pad sealing part. A damages of sleeve and piston head, bush are caused by friction and wear. Thus, It is necessary to examine friction and wear characteristics of Cu alloys for the piston head and bush. In this study, to be reliable on the piston and cylinder parts, dry friction and wear experiments were carried out with Cu alloys of four kinds of AlBC, PBC, BC and BS using reciprocating friction tester of pin on disk type. From this study, the result was shown that the AlBC and PBC with alloy elements were excellent to resistance wear. As the sliding speed was increased, the wear loss of PBC decreased than another Cu alloy.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.69-74
• /
• 2006

It is known that the various noise sources which are engine, transmission, tire, intake system, etc exist at vehicle driving status. Specially noises which cannot be expected by a driver induce unpleasantness to all passengers. These noises are difficult to distinguish noise sources or specifications because of too many vehicle parts. Therefore in this paper, study on abnormal noise of bush on suspension system is performed by the measurement and analysis of the noises of bushings that are generated artificially. The measured noises are analyzed by two points-view of spectrum and sound quality. Finally, it is shown that the noise sources of bushings on the suspension system which are the pillow ball joint bush of a control arm and the rubber bush of a lower arm could be distinguished by the spectrum distribution and a index value based on tonality.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.11
• /
• pp.1244-1248
• /
• 2009

Although rubber components are extensively used in mechanic parts. There are still a lot of difficulties in designing the rubber components applied in complex shapes and preloaded states because of the complicated material properties. One of the most important parameters for more detailed and accurate mechanical analysis during the development stages is the dynamic characteristics of the rubber components. It is well known that the dynamic properties of rubber are dependent on frequency as well as static preload. Consequently, a large number of experiments have to be conducted to identify the dynamic stiffness of a rubber bush considering the various applied conditions. In this paper, an efficient experimental method is suggested, which estimates the dynamic stiffness of a rubber bush using rubber material test and static stiffness of the bush. This method is capable of predicting the dynamic stiffness of a rubber bush under various load conditions from minimized test data.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.453-458
• /
• 2008

Under driving condition, A vehicle experiences various kinds of loads, which brings on the buckling and fracture of suspension systems. Lower control arm (LCA), which consists of 2 bush joints and 1 ball joint connection, is the one of the most important parts in the suspension system. The bush joints absorb the impact load and reduce the vibration from the road. When analyzing the LCA behavior, it is important to understand the material properties and boundary conditions of bushing systems correctly, because of the nonlinearity characteristics of the rubber. In this paper, in order to predict the large scale deformation of the LCA more precisely, three factors are newly suggested, that is, coupling of bush stiffness between translation and rotation, bush extraction force and maximum rotation angle of ball joint. LCA stiffness is estimated by CAE and component test. Analysis and test results are almost same and the validity of considering three factors in LCA analysis is verified.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.6
• /
• pp.666-674
• /
• 2007

It is very important to estimate static squeezing pressure distributions for lining material of sterntube after bearing at dry dock stage since the maximum squeezing pressure value can be one of the significant characteristics representing coming navigation performances of the propulsion system. Moderate oil film pressure between lining material and propulsion shaft is also essential for safe ship service. In this paper, Hertz contact theory is explained to derive static squeezing pressure. Reynolds equation simplified from Navier-Stokes equation is centrally differentiated to numerically obtain dynamic oil film pressures. New shaft alignment technology of nonlinear elastic multi-support bearing elements is also used in order to obtain external forces acting on lining material of bearing. For 300K DWT class VLCC with synthetic bush of sterntube after bearing, static squeezing pressures are calculated using derived external forces and Hertz contact theory. Optimum partial slope of the after bush is presented by parametric shaft alignment analyses. Dynamic oil film pressures are comparatively evaluated for partially bored and unbored after bush. Finally it is proved that the partial slope can drastically reduce oil film pressure during engine running.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.7
• /
• pp.827-835
• /
• 2016

Ride comfort of a vehicle is often determined by rubber bushes in suspension system. If transmission forces versus deformations across the bushes are available under operational conditions, improvement of the ride comfort could be done with more ease. Recently, the transmission forces are measured using custom-made force transducers inside the links. This study presents a feasibility study on estimation of the rubber bush deformations using vibration signals on the rigid links. Linear variable displacement transducers as well as piezoelectric accelerometers are used to expand frequency range to very low frequency, which cannot be done with accelerometers only. How to estimate the bush deformation from the two vibration signals on the links are presented together with experimental results.

• Journal of Applied Reliability
• /
• v.17 no.2
• /
• pp.143-149
• /
• 2017

Purpose: In recent years, weight reduction for improving fuel efficiency of the vehicle and cost reduction have been developed. The structure of suspension link is widely used as a single plate press structure which can reduce process and weight compared to existing pipe welding method. However, it was found that the lifetime of a single plate press structure is determined by initial defects that occurred during initial manufacturing rather than fatigue damage caused by driving. Methods: I research the mechanism of failure phenomenon of the single plate press assist arm of rear wheel. In addition, I investigate durability effect parameters to determine the link lifetime in inserting bush into single plate press process through durability test. Conclusion: I discover significant durability effect parameter in inserting bush into single plate press process. It is expected that the durability can be improved by suggesting a bush inserting process inspection guide for similar suspension link like single plate press structure.

• The Korean Journal of Zoology
• /
• v.13 no.1
• /
• pp.3-8
• /
• 1970

1. Paju area of Kyonggydo has received serious damages by Dryocosmus kuriphilus Yasumatsu in the bushes of Castanea crenata S. et Z. since 1965. I have also found the middle parts of whole country of Korea has damaged by this wasp. 2. Bobwonri was the worst case in its damage by Dryocosmus kuriphilus Yasumatsu with most prosperous parasite, Aletia flavostigma singularis Butler and Dictyoploca japonica Moore. I conclude that this is the result of the lack of beneficial insects and isolated bush formation. 3. The chestnut bush at Bunsuri was recovering from the damage of gall wasp nevertheless it was illustrated big damage at last year's hranches. I conclude that this recovering phenomena is closely related with the insect fauna of this area and this characteristic insect fauna was derived from the bush formation which reveals specific bush arrangement that can be illustrated as surrounded by another bush of Quercus acutissima Carruthers. 4. As a final conclusion, I recommend mixed bush formation of chestnut tree with Quercus species to control insect population dynamics in healthy status.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.349-350
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.349-350
• /
• 2010