• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.262-264
• /
• 1999

The AC losses of BSCCO-2223 multifilamentary superconducting tapes were measured using magnetization method and compared with the results of theoretically calculated values. In general, AC losses in multifilamentary superconducting tapes could be quantitatively explained by the simple sum of the Hysteresis and Coupling Loss. As a result of experiment, We found that AC losses of multifilamentary superconducting tape increase rapidly in large magnetic field region.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.97-100
• /
• 2004

In this paper, the preparation of BSCCO superconducting wire by electrophoretic deposition method and the effect of suspension medium used with various solvent solutions of ethanol and buthanol for electrophoretic deposition were studied. The preheating technique in vacuum system for the superconducting powders coated on Ag wire was also investigated. As a result, it was confirmed that the preheating technique was very useful to remove the influence of remains affected to the surface conditions of superconducting wire. And the adsorbed solvent solution which was existed between and on the deposited particle surfaces was almost disappeared at the treating conditions of about $10^{-3}$ Torr and around $200^{\circ}C$ in bell-jar system. By measurement of 4-point prove method, the critical current density($J_c$) of BSCCO superconducting wire was obtained at the value of more than $10^4\;A/cm^2$ in liquid $N_2$(77 K, 0 T).

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.538-541
• /
• 2003

BSCCO superconducting thin films have been fabricated by co-deposition using IBS(Ion Beam Sputtering) method. Despite setting the composition of thin film Bi2212 or Bi2223, in both cases, Bi2201, Bi2212 and Bi2223 phase were appeared. It was confirmed the obtained field of stabilizing phase was represented in the diagonal direction of the right below end in the Arrhenius plot of temperature of the substrate and PO$_3$, and it was distributed in the rezone. The XRD peak of the generated film continuously changed according to the substrate temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.270-273
• /
• 2000

For the well-preparation of the superconducting wire by electrophoresis, the control of the cracking on the YBCO, BSCCO superconductor deposited on Ag wire in acetone and buthanol solution with PEG(poly-ethylenglycol) was investigated with XRD and SEM analysis. After deposition, drying and heat treatment process, the cracks on the deposited surface of YBCO and BSCCO samples was clearly removed and decreased, which was perpared in suspension with addition of PEG from 1 to 3ml. However, in the case of the addition rate of PEG in acetone suspension was exceeded in 3ml, BSCCO superconductor deposited on Ag wire was slightly melted at 90$0^{\circ}C$ which was the same heat treatment condition of other samples with different additin rate of PEG. In the process of electrophoretic deposition, drying and heat treatment, PEG added into the suspension solution as a binder was very useful to prepare the crack-free thick film-wire of YBCO and BSCCO.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.214-214
• /
• 2009

While critical properties of BSCCO wires rely considerably on grid direction upon BSCCO and have very complicated mechanism of generating a superconducting phase, making it difficult to improve properties of wires, YBCO thin-film wires which can be formed in a superconducting phase upon metal board through vapor deposition processing can get excellent direction and reduce manufacturing costs with more flexibility in improving critical properties; thus, they will be suitable for instrument application in the future. Contrary to BSCCO wires for which thick silver alloy covering materials should inevitably be used, moreover, YBCO thin-film wires have an advantage of making thickness and quality of covering materials different by usage. Such a property can be an important element to widen application of wires by presenting possibility of using thin-film wires as superconducting material for fault current limiter as well as for high power current application. In this study we intend to prepare YBCO thin-film wires with different stabilizer layers to analyze current application and current restriction properties by stabilizer layers on the basis of detailed researches on changes in current classification properties below critical value.

• 연구논문집
• /
• s.27
• /
• pp.175-181
• /
• 1997

Superconducting joints between Bi-2223/Ag tapes are fabricated by a press & reaction anneal and a multiple press & anneal. The silver sheath was mechanically or chemically removed from one side of each tape without altering the superconducting core. The exposed superconducting core of the two tapes were brought into contact and pressed so as to form a lap joint. The joined tapes were then subjected to a series of different thermomechanical treatments to achieve optimum heat treatment condition. The result from transport measurements shows that critical current ($I_c$) transmitting through joined area reaches 9A, approximately 60% of the current capacity of the tapes themselves. The critical current through joined area was improved by repeated press and reaction annealing. Measurements of the current-voltage relationship were made with several configuration of the voltage probes to characterize the critical current variation and I-V curve along the joint. Also discussed are microstructural aspects of the superconducting joint.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.105-108
• /
• 2002

For fabricating high T$\sub$c/ superconducting deposited film, novel electrophoretic deposition technique applied to deposit surface charged Particles on metal substrate with oxy d.c field has been studied. The electric properties of superconducting film don't improve easily because the particles of deposition film are deposited randomly on substrate and don't make orientation affected to its critical current density. In this paper, we studied conventional electrophoresis in addition to a.c field assisted for the improvement of BSCCO superconducting film with high orientation of deposition particles.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.2
• /
• pp.157-162
• /
• 2003

For fabricating high T$\sub$c/ superconducting deposition film, novel electrophoretic deposition (EPD) technique applied to deposit surface charged particles on metal substrate with only d.c field has been studied. However, the electric properties of superconducting film could not be improved easily by this way, because the particles of EPD film were usually deposited randomly on metal substrate without any directional orientation affected to its critical current density. For the purpose of obtaining partcle orientation on the EPD films, the new method modified by a.c. assisted field to the conventional electrophoresis system was investigated to improve the particle deposition density and to increase the contacting area among the particles with highly oriented particle deposition of BSCCO superconducting film.

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.4
• /
• pp.158-160
• /
• 2004

BiSrCaCuO thick films were fabricated by plasma enhanced chemical vapor deposition, and the crystallinity and the superconducting properties were investigated. The superconductivity was achieved at 20 K with an onset temperature of around 90 K in the film prepared at 72$0^{\circ}C$. From X ray diffraction analysis, the main superconducting phase in the films was the low Tc phase at 700∼75$0^{\circ}C$ and the high Tc phase at 750 ∼ 80$0^{\circ}C$.

• Progress in Superconductivity
• /
• v.7 no.2
• /
• pp.179-183
• /
• 2006

As a material for SFCL(Superconducting Fault Current Limiter), BSCCO tube with metal stabilizer is a promising candidate, assuring the stability and large power capacity, For the application, the proper soldering technique, which overcome the difficulties of the joining between BSCCO and metal stabilizer, is required. In this study, after soldering In-Bi solder and In-Sn solder with BSCCO superconductor, welding properties between BSCCO and solders were investigated. Because ceramic materials is difficult to weld, Ag electro-plating on BSCCO 2212 is used for intermetallic layer. To find out the best welding condition for superconductor, soldering is tested in the maximum temperature from $155^{\circ}C\;to\;165^{\circ}C$ in the reflow oven. By investigating the composition and thickness of IMC (lntermetallic Compound) created in the reaction of Ag with solder, we analyzed the welding properties of High-Tc superconductor from a micro point of view.