• Proceedings of the KIEE Conference
• /
• 1997.07e
• /
• pp.1705-1707
• /
• 1997

In this work, a possible new PD de technique, based on the electro-optic effect(P effect), has been proposed. The refractive index ellipsoid of EO crystal, as $LiNbO_3$, is changed by both the externally a electric field and its hysteresis loop of which effect on this hysteresis loop gives rise t discrepancy of index variation. Therefore, an eq regarding the phase variation of modulated beam through $LiNbO_3$ crystal under applied e field, is newly proposed considering the influen hysteresis characteristics. For this purpose generated from needle-plane electrode in oil has detected by use of $LiNbO_3$ cell and analyzed b equation. As a result, it is observed that PD measu phase intervals are limited by the cr characteristics such as asymmertrical P-E hyst and half-wave voltage.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05c
• /
• pp.93-96
• /
• 2002

In this study, PZT thin films were fabricated using sol-gel processing onto Si/$SiO_2$/Ti/Pt substrates. PZT sol with different Zr/Ti ratio(20/80, 30/70, 40/60, 52/48) were prepared, respectively. The films were fabricated by using the spin-coating method on substrates. The films were heat treated at $450^{\circ}C$, $650^{\circ}C$ by rapid thermal annealing(RTA). The preferred orientation of the PZT thin films were observed by X-ray diffraction(XRD), and Scanning electron microscopy(SEM). All of the resulting PZT thin films were crystallized with perovskite phase. The fine crystallinity of the films were fabricated. Also, we found that the ferroelectric properties from the dielectric constant of the PZT thin films were over 600 degrees, P-E hysteresis constant. And the leakage current densities of films were lower than $10^{-8}A/cm^2$. It is concluded that the PZT thin films by sol-gel process to be convinced of application for ferroelectric memory device.

• Journal of the Korean Ceramic Society
• /
• v.19 no.4
• /
• pp.267-274
• /
• 1982

The sintering behavior and B-H loop properties of $Li_{0.5O4}$ with the addition of $Nb_2O_5$ and $V_2O_5$ have been investigated by observation of microstructures and measurement of semi-static hysteresis loops. The sintering temperature was lowered by the additions of $Nb_2O_5$ and $V_2O_5$ and the effect of $V_2O_5$ addition was greater than that of $Nb_2O_5$. The abnormal grain growth was observed at about 100$0^{\circ}C$(d:4.6g/㎤) and 85$0^{\circ}C$(d:4.5g/㎤) in the specimens with the addition of $Nb_2O_5$ and $V_2O_5$ respectively. The addition of $Nb_2O_5$ retulted in a large and uniform grain size, and the addition of $V_2O_5$ resulted in a uniform grain size but the final density was lower than that of the pure specimen. The squareness was increased and the coercive force was decreased by the addition of $Nb_2O_5$, and the squareness was decreased and the coercive force was increased by the addition of $V_2O_5$. These effects could be explained by a large and uniform grain size, and by a lower final density of specimens with the addition of $Nb_2O_5$ and $V_2O_5$ respectively.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.606-609
• /
• 1995

Ferrite cores are often magnetized under DC-biased field because they have been intensively used in electronic circuits such as an inverter circuit and a switching regulator circuit. Thus we investigated the effects of DC-biased field on magnetic properties in the frequency range of DC-100kHz for two kinds of ferrite cores, TDK PC38 and TDK $H_{3}S$, which have different shapes of B-H loop from each other. The magnetic loss per cycle, W/f, in the $H_{3}S$ core decreased with increasing the strength of DC-biased field, although W/f in the PC38 core increased monotonically with DC-biased field. The observed decreasing tendency differs from the previous result for Si-Fe and ferrite cores, and can be attributed to decrease in eddy current loss as well as that in hysteresis loss.

• Journal of Korea Water Resources Association
• /
• v.39 no.6 s.167
• /
• pp.487-494
• /
• 2006

The flood discharge on the rising limb of a hydrograph at Hwawon station greatly differs from the flood discharge on the falling limb for the same stage. When there is such a big hysteresis, there can be a significant amount of errors in the rated discharge obtained from a simple rating curve. To reduce errors in rated discharges, a looped rating curve was established for Hwawon station in the Nakdong River. In order to compute the deviation between real discharges and simply rated discharges, a simple rating curve was established using the stage and discharge data from the results of a hydraulic channel routing. The relationship between the discharge deviation ${\Delta}Q$ and a product of B and ${\Delta}h/{\Delta}t$ was analysed, where B is the channel topwidth; ${\Delta}h$ is the stage increment; At is the time increment. Strong relation between ${\Delta}Q$ and $B{\Delta}h/{\Delta}t$ was found. The discharges calculated from the relationship show differences by 10 % or less for the 7 observations out of 11 observations in 1997 whose stages exceeds 7 m. The observed discharges for the stages over 9 m in 1998 also show small difference with the discharges estimated from the loop rating curve. Looped rating curve is recommended, instead of the simple rating curve to reduce the errors of rated discharges for gauging stations like Hwawon, which has relatively large loop width.

• Journal of the Korean Magnetics Society
• /
• v.25 no.4
• /
• pp.123-128
• /
• 2015

The iron is an element having a high yield strength, mechanical hardness, good electrical conductivity, and also it has been used in various fields because of ease machining. In bridges have been used tendon made of a steel wire for large loads and light weight. Tension measurement of tendon employed in PreStressed Concrete (PSC) bridge is very important for the bridge safety check. NDT (Non-Destructive Testing) is essential for the safety check, however, magnetic NDT is difficult to apply due to the non-linear magnetization curve and hysteresis loop in the magnetic properties. In this work, for basic study of magnetic NDT application, we have constructed a B-H loop measuring system for 7-strand tendon of which diameter is 15.5 mm, and which can apply tensile stress up to 2.0 GPa. We have measured hysteresis loops of two kinds of tendons under different tensile stress. Amplitude permeability and maximum magnetic induction near knee show the most sensitive and high linearity depends on tensile stress. Relative amplitude permeability was decreased from 500 to 200 and maximum magnetic flux density changed 0.6 T.

• Journal of Magnetics
• /
• v.3 no.2
• /
• pp.55-63
• /
• 1998

Magnetic and magnetostrictive properties of amorphous Sm-Fe and Sm-Fe-B thin films are systematically investigated over a wide composition range from 14.1 to 71.7 at.% Sm. The films were fabricated by rf magnetron sputtering using a composite target composed of an Fe (or Fe-B) plate and Sm chips. The amount of B added ranges from 0.3 to 0.8 at. %. The microstructure, examined by X-ray diffraction, mainly consists of an amorphous phase in the intermediate Sm content range from 20 to 45 at.%. Together with an amorphous phase, crystalline phases of Fe and Sm also exist at low and high ends of the Sm content, respectively. Well-developed in-plane anisotropy is formed over the whole compositionrange, except for the low Sm content below 15 at.% and the high Sm content above 55 at %. As the Sm content increases, the saturation magnetization decreases linearly and the coercive force tends to increase, with the exception of the low Sm content where very large magnitudes of the saturation magnetization and the coercive force are observed due to the existence of the crystalline $\alpha$-Fe phase. The coercive force is affected rather substantially by the B addition, resulting in lower values of the coercive force in the practically important Sm content range of 30 to 40 at.%. Good magnetic softness indicated by well-developed in-plane anisotropy, a square-shaped hysteresis loop and a low magnitude of the coercive force results in good magnetostrictive characteristics in both Sm-Fe-B thin films. The magnetostrictive characteristics, particularly at low magnetic fields, are further improved by the addition of B; for example, at a magnetic field of 100 Oe, the magnitude of magnetostriction is -350 ppm in a Sm-Fe thin film and it is -470 ppm in a B containing Sm-Fe thin film.

• Journal of Magnetics
• /
• v.16 no.2
• /
• pp.83-87
• /
• 2011

The vortex-driven magnetization process of micron-sized, exchange-coupled square elements with composition of $Ni_{80}Fe_{20}$ (12 nm)/$Ir_{20}Mn_{80}$ (5 nm) is investigated. The exchange-bias is introduced by field-cooling through the blocking temperature (TB) of the system, whereby Landau-shaped vortex states of the $Ni_{80}Fe_{20}$ layer are imprinted into the $Ir_{20}Mn_{80}$. In the case of zero-field cooling, the exchange-coupling at the ferromagnetic/antiferromagnetic interface significantly enhances the vortex stability by increasing the nucleation and annihilation fields, while reducing coercivity and remanence. For the field-cooled elements, the hysteresis loops are shifted along the cooling field axis. The loop shift is attributed to the imprinting of displaced vortex state of $Ni_{80}Fe_{20}$ into $Ir_{20}Mn_{80}$, which leads to asymmetric effective local pinning fields at the interface. The asymmetry of the hysteresis loop and the strength of the exchange-bias field can be tuned by varying the strength of cooling field. Micromagnetic modeling reproduces the experimentally observed vortex-driven magnetization process if the local pinning fields induced by exchange-coupling of the ferromagnetic and antiferromagnetic layers are taken into account.

• Journal of Power Electronics
• /
• v.8 no.3
• /
• pp.217-227
• /
• 2008

The electric power subsystems (EPS) of most remote sensing satellites consist of a solar array as a source of energy, a storage battery, a power management and control (PMC) unit and a charge equalization unit (CEU) for the storage battery. The PMC and CEU use high frequency transformers in their power modules. This paper presents a design, implementation and testing results of a high frequency transformer for the EPS of satellite applications. Two approaches are used in the design process of the transformer based on the pre-determined transformer specifications. The transformer is designed based on an ETD 29 ferrite core. The implemented transformer consists of one center-tapped primary coil with eleven center-tapped secondary coils. The offline calculation results and measured values of R, L for transformer coils are convergence. A test circuit for measuring the transformer parameters like voltage, current and B-H hysteresis was implemented and applied. The test results confirm that the voltage waveforms of both primary and secondary coils were as desired. No overlapping occurred between the control signal and the transformer, which was not saturated during testing even during a short circuit test of the secondary channels. The dynamic B-H loop characteristics of the used transformer cores were measured. The sample test results are given in this paper.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.343-344
• /
• 2006

방향성 규소강판을 tape-wound core 형태로 제작하여 가공방법에 따른 자기적 특성을 조사 하였다. 그 결과 곡률반경이 40mm인 시료에서 보자력(Hc)과 포화자속밀도(Bs)는 우수한 값을 나타내었고, 보자력은 0.02Oe, 포화자속밀도는 1.85T 이었다. 현재 국내에서 생산되고 있는 방향성 규소강판의 자속밀도값 보다 우수한 값을 나타내었다. 본 연구로부터 방향성 규소강판을 이용하여 권자심을 제작할 때 도입되는 탄성변형에 대한 대책의 중요성과 코어 소재의 가공방법이 자기적 특성에 미치는 영향을 통해 고효율 방향성 규소강판 개발의 가능성을 확인하였다.