• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.4
• /
• pp.52-62
• /
• 1996

In this paper, a new continuous-time current-mode integrator as basic building block of the low-voltage analog current-mode active filters was proposed. Compared to the current-mode integrator which was proposed by Zele, the proposed current-mode integrator had higher unity gain frequency and output impedance in addition to lower power dissipation. And also, a current-mode third-order lowpass active filter was designed with the proposed current-mode integrator. The designed circuits were fabricated using the ORBIT's 1.2.mu.m double-poly double-metal CMOS n-well process. The experimental resutls of the active filter designed and fabricated for this research have shown that it has the performance of 44.5MHz cutoff frequency, 3.3mW power dissipation and the third-order active filter area was 0.12mm$^{2}$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.517-531
• /
• 1999

This paper presents the development of the 2-mode variable gain high power amplifier for a transmitter of INMARSAT-M operating at L-band(1626.5-1646.5 MHz). This SSPA(Solid State Power Amplifier) is amplified 42 dBm in high power mode and 36 dBm in low power mode for INMARSAT-M. The allowable error sets +1 dBm of an upper limit and -2 dBm of a lower limit, respectively. To simplify the fabrication process, the whole system is designed by two parts composed of a driving amplifier and a high power amplifier, The HP's MGA-64135 and Motorola's MRF-6401 are used for driving amplifier, and the ERICSSON's PTE-10114 and PTF-10021 are used the high power amplifier. The SSPA was fabricated by the circuits of RF, temperature compensation and 2-mode gain control circuit in aluminum housing. The gain control method was proposed by controlling the voltage for the 2-mode. In addition, It has been experimentally verified that the gain is controlled for single tone signal as well as two tone signals. The realized SSPA has 42 dB and 36 dB for small signal gain within 20 MHz bandwidth, and the VSWR of input and output port is less than 1.5:1 The minimum value of the 1 dB compression point gets 5 dBm for 2-mode variable gain high power amplifier. A typical two tone intermodulation point has 32.5 dBc maximum which is single carrier backed off 3 dB from 1 dB compression point. The maximum output power of 43 dBm was achieved at the 1636.5 MHz. These results reveal a high power of 20 Watt, which was the design target.the design target.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3614-3621
• /
• 2009

In this paper, A CMOS low-voltage current mode integrator is designed. The designed current-mode integrator is based on linear cascode circuit that is newly proposed in this paper. When it is compared with gain(43.7dB) and unity gain frequency(15.2MHz) of the typical current-mirror type current-mode integrator, the proposed linear cascode current-mode integrator achieves high current gain(47.8dB) and unity gain frequency(27.8MHz). And a 5th Chebyshev current-mode filter with 7.03MHz cutoff frequency is designed. The designed all circuits are simulated by HSPICE using 1.8V-$0.18{\mu}m$ CMOS technology.

• Journal of Satellite, Information and Communications
• /
• v.8 no.3
• /
• pp.47-51
• /
• 2013

In this paper, we present design and test results of a Ka-band dual-band ortho-mode transducer (OMT) for use in a feed assembly for the very small aperture terminals (VSATs). The designed ortho-mode transducer have wideband characteristics to separate the signals that have two orthogonal linear polarizations operating at 20GHz of receive frequency band and at 30GHz of transmit frequency band. In addition, in order to reduce the volume of the feed assebly, a Boifot based ortho-mode transducer has been designed with a dual-band. Experimental results for the design verification, the return loss in the receive band and in the transmit band for the horizontal polarization showed over 20dB and 21dB, respectively, and for the vertical polarization showed over 20dB and 24dB, respectively. The port isolation for the horizontal polarization and the vertical polarization showed over 43dB and 52dB, respectively, in the receive band and in the vertical band.

• ETRI Journal
• /
• v.18 no.4
• /
• pp.287-299
• /
• 1997

Integrated-optic polarization controlling devices such as polarizers, polarization splitters, and polarization converters, are proposed and demonstrated in nonlinear optic polymers. Poling-induced birefringence in electro-optic polymers is exploited to fabricate the devices. The polymeric waveguide polarizers show low excess losses, and extinction ratios of 20.7 dB and 17.1 dB for TM-pass and TE-pass polarizers, respectively. The polymeric waveguide polarization splitters exhibit TE-TM mode splittings with crosstalk of 14.2 dB and 10.1 dB for TM and TE mode splittings, respectively. The polymeric waveguide polarization converters show successful TE/TM polarization mode conversion with conversion efficiencies of higher than 30 dB. The device employs poling-induced waveguides which have slowly rotating azimuth angle of optic axis along the light propagation direction. The novel polarization converter is insensitive to wavelength and easier to fabricate than the other polarization converters containing periodic structures.

• Journal of Biomedical Engineering Research
• /
• v.24 no.3
• /
• pp.141-149
• /
• 2003

This paper proposes a method of measuring and imaging the stiffness of human soft tissue to diagnose cancers or tumors which have been difficult to detect in ultrasound B-mode imaging systems. To measure the soft tissue stiffness, sinusoidal vibrations are applied to it, and the magnitude of its mechanical vibration is determined by estimating the temporal variation of speckle pattern brightness in ultrasound B-mode images. It is verified by simulation and experiment that the proposed method can estimate the relative tissue stiffness from B-mode images with a relatively small amount of computation.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.28B no.10
• /
• pp.822-830
• /
• 1991

In this paper, we propose a new process for ultrasonic B-mode image considering the sound field effects of a concave circuit focused transducer, and aim to remove the speckle pattern which cause the blurring on boundary in ultrasonic B-mode image. We discuss in detail the conception of speckle pattern generation, and the frequency compounding method which is applied to the process for getting a speckle reduced B-mode image. Through the computer simulation, we define the meaning of speckle region, and show the results of reduced speckle pattern. It is discovered in the results that the frequency compounding method is very effective for boundary detection and that the application of the method is limited by various conditions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.414-417
• /
• 2001

Recently, developments of device using characteristics of ceramics as a new technical material is in progress. While doing so, Ultrasonic motor which is a part of research & development of piezo-actuator by piezo-effects is being used in the various applications. So, we fabricated a flat-type $L_{1}-B_{8}$ mode Ultrasonic motor and measured the operation characteristics of its. The size of USM is 80*20*1.5[$mm^{3}$](length*width*thickness) and is constructed with stator by piezo-ceramics and stainless elastic body and rotator by bearings. As results of experiments, the fastest speed of revolution(v), the maximum torque(T) and the efficiency( $\eta$ ) were 37.5[cm/sec], 5.0[ $mN{\cdot}m$ ] and 1.17[%] respectively when 27.9[kHz], 150[gf], 50[V] were applied. So, we think this $flat-type_{1}-B_{8}$ mode Ultrasonic motor is able to be used for applications in forwarding device of a paper or electric card and so on.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.9
• /
• pp.1229-1235
• /
• 1995

In this paper an elliptic response dual-mode 4-pole bandpass filter was designed, manu-factured, and tested. A dual-mode filter having two stages cascaded double-tuned cavities which are resonant in two independent orthogonal TE113 circular-cavity modes and provide a bandpass response. A 4-pole dual-mode elliptic function bandpass filter has a center frequency of 14.022 GHz with a bandwidth of 36 MHz which is the first channel of the KOREASAT up-link frequency. The measured experimental results of a dual-mode filter are 1 dB insertion loss in the passband and 20 dB out-of-rejection.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.73-76
• /
• 1997

A low loss x-cut LiNbO$_3$ optical waveguide was fabricated by Ti in-diffusion and the guided-mode properties and total insertion loss of pigtailing with polarization maintaining fiber(PMF) were investigated and measured at optical wavelength 15507. For formaing the waveguide, the parameters of diffusion Ti thickness, waveguide line-width, length, diffusion temperature, time and atmosphere were set 1400$\AA$, 8${\mu}{\textrm}{m}$, 3.3cm, 105$0^{\circ}C$, 8 hours and wet bubbled oxygen, respectively. and then After the polishing and pigtailing, it showed that total insertion loss was -4.1dB for TM mode, -5.5dB for TE mode, and mode size, that is, horizontal/vertical sizes were 13.87/18${\mu}{\textrm}{m}$ for TM mode, 9.61${\mu}{\textrm}{m}$/6.5${\mu}{\textrm}{m}$ for TE mode.