• 대한전자공학회논문지SD
• /
• 제47권3호
• /
• pp.51-57
• /
• 2010

IEEE 802.11n 기반 무선 LAN과 IEEE 802.16e 기반 Mobile WiMAX에 적용할 수 있는 이중모드 직접 변환 수신기를 $0.13\;{\mu}m$ RF CMOS 공정을 이용하여 설계하였다. 설계된 직접 변환 수신기는 2.3-2.7 GHz의 주파수 범위에서 동작을 한다. 저잡음 증폭기에 Current Steering 기술을 사용하여 전체 이득의 크기를 3 단계로 조절이 가능하게 하였다. 플리커 잡음 영향을 낮추기 위해 믹서에 Current Bleeding 기술을 사용하였다. 믹서 LO를 위한 I/Q 위상 신호 발생을 위해 주파수 2-분주회로를 포함하였다. 제작된 직접 변환 수신기는 1.4V의 공급 전원에서 LO 버퍼를 포함하여 56 mA를 사용하며, 32 dB의 전력이득과 4.8dB의 잡음지수, 그리고 +6 dBm의 출력 $P_{1dB}$를 가진다.

• 한국전자파학회논문지
• /
• 제26권7호
• /
• pp.675-678
• /
• 2015

본 논문은 마이크로웨이브 수신기 구성을 위한 다기능 주파수 변환 블록을 설계 및 제작하였다. 제안한 다기능 주파수 변환 블록은 광대역 전압제어발진기와 이중모드 주파수 혼합기로 구성되어, 바이어스 전압 인가 여부에 따라 마이크로웨이브 수신기에 필요한 첫 번째 IF(Intermediate Frequency) 출력 주파수 4,595 MHz / 6,045 MHz는 720 MHz로 주파수 변환을 하고, Ku-대역 수신을 위한 IF 출력 주파수 720 MHz는 주파수 변환을 하지 않고 통과(bypass) 및 감쇄시키는 이중모드의 다기능 동작을 한다. 제작 및 측정결과, 각 중간주파수에서 LO 전력에 따른 변환손실 특성은 2~4 dBm의 LO 레벨에서 4,595 MHz는 13 dB, 6,035 MHz에서 12 dB, 720 MHz에서는 7.0 dB의 변환손실 특성을 나타내었다.

• 설비공학논문집
• /
• 제17권2호
• /
• pp.101-109
• /
• 2005

The purpose of this study is to investigate the performance of outdoor heat exchanger for heat pump using carbon dioxide. Two types of fin and tube heat exchangers (2 rows for type A and 3 rows for B) are tested. Both heat exchangers have counter-cross flow and 1-circuit arrangement. Test results such as heat transfer rate, pressure drop characteristics and temperature distribution in the heat exchanger are shown with respect to mass flow rate of refrigerant and frontal air velocity For cooling mode, the minimum temperature difference between air and refrigerant of type B is smaller than that of type A by $1^{circ}C$, but the pressure loss of air side is much higher for type B by $29\%$. It is found that a large temperature gradient of carbon dioxide during gas cooling Process Promotes thermal conduction through tube wall and fins which results in degradation of heat transfer performance. For heating mode operation, type B heat exchanger shows higher heat transfer performance compared to type A. However, because pressure loss of refrigerant side of type B is much greater than that of type A, the refrigerant outlet pressure of type B becomes lower than that of type A.

• 전기전자학회논문지
• /
• 제14권4호
• /
• pp.257-262
• /
• 2010

본 논문에서는 5.25 GHz에서 넓은 이득 제어범위를 갖는 저전력 가변 이득 프론트-엔드를 설계하였다. 넓은 이득 제어범위를 갖기 위해, 제안된 저잡음 증폭에서는 가변이득 증폭기의 소스에 p-타입 트랜지스터를 연결하였다. 이 방법을 통해 증폭기의 바이어스 전류와 소스 임피던스를 동시에 조절할 수 있었다. 따라서 제안된 저잡음 증폭기는 넓은 이득 제어범위를 갖는다. 믹서에서는 입력 트랜스컨덕턴스단으로 p-타입 트랜지스터를 사용한 폴디드 구조가 제안되었다. 이 구조에서 믹서는 작은 공급 전압에서 각 단에 필요한 만큼의 전류만 흘려주기 때문에 저전력에서도 작동을 할 수 있다. 제안된 프론트-엔드는 최대 33.2 dB의 이득과 17 dB의 넓은 이득 제어범위를 갖는다. 이 때, 잡음지수와 IIP3는 각각 4.8 dB, -8.5 dBm을 갖는다. 이러한 동작을 하는 동안, 제안된 회로는 최대 이득상태에서 7.1 mW, 최소 이득상태에서 2.6 mW의 적은 전력을 소비한다. 시뮬레이션 결과는 TSMC $0.18\;{\mu}m$ CMOS 공정에서 Cadence를 이용하여 얻어졌다.

• 한국전자파학회논문지
• /
• 제21권3호
• /
• pp.292-300
• /
• 2010

본 논문은 광대역과 다중 대역 특성을 갖는 DVB-H 수신기에 적합한 혼성 변환 방식의 RF 전단부 구조를 제안하고, 이의 구현을 위한 다중 기능 회로를 제작하여 측정하였다. 다중 기능 회로는 광대역 VHF/UHF-대역을 수신하는 경우, 변환 손실 -10.0 dB, 잡음 지수 7.0 dB, IIP3 2.0 dBm을 갖는 부고조파 혼합기 모드로 동작하고, 다중 대역, L-대역 신호를 수신하는 경우, 삽입 손실 -10.0 dB를 갖는 감쇄 모드로 동작한다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제24권12호
• /
• pp.1644-1650
• /
• 2011

This study was conducted to detect quantitative trait loci (QTL) affecting meat quality in an $F_2$ reference population of Korean native pig and Landrace crossbreds. The three-generation mapping population was generated with 411 progeny from 38 $F_2$ full-sib families, and 133 genetic markers were used to produce a sex-average map of the 17 autosomes. The data set was analyzed using least squares Mendelian and parent-of-origin interval-mapping models. Lack-of-fit tests between models were used to characterize the QTL for mode of gene expressions. A total of 10 (32) QTL were detected at the 5% genome (chromosome)-wise level for the analyzed traits. Of the 42 QTL detected, 13 QTL were classified as Mendelian, 10 as paternal, 14 as maternal, and 5 as partial expressed QTL, respectively. Among the QTL detected at 5% genome-wise level, four QTL had Mendelian mode of inheritance on SSCs 5, 10, 12, and 13 for cooking loss, drip loss, crude lipid and crude protein, respectively; two QTL maternal inheritance for pH at 24-h and shear force on SSC11; three QTL paternal inheritance for CIE b and Hunter b on SSC9 and for cooking loss on SSC15; and one QTL partial expression for crude ash on SSC13, respectively. Most of the Mendelian QTL (9 of 13) had a dominant mode of gene action, suggesting potential utilization of heterosis for genetic improvement of meat quality within the cross population via marker-assisted selection.

• ETRI Journal
• /
• 제36권3호
• /
• pp.352-360
• /
• 2014

This paper presents a 900 MHz zero-IF RF transceiver for IEEE 802.15.4g Smart Utility Networks OFDM systems. The proposed RF transceiver comprises an RF front end, a Tx baseband analog circuit, an Rx baseband analog circuit, and a ${\Delta}{\Sigma}$ fractional-N frequency synthesizer. In the RF front end, re-use of a matching network reduces the chip size of the RF transceiver. Since a T/Rx switch is implemented only at the input of the low noise amplifier, the driver amplifier can deliver its output power to an antenna without any signal loss; thus, leading to a low dc power consumption. The proposed current-driven passive mixer in Rx and voltage-mode passive mixer in Tx can mitigate the IQ crosstalk problem, while maintaining 50% duty-cycle in local oscillator clocks. The overall Rx-baseband circuits can provide a voltage gain of 70 dB with a 1 dB gain control step. The proposed RF transceiver is implemented in a $0.18{\mu}$ CMOS technology and consumes 37 mA in Tx mode and 38 mA in Rx mode from a 1.8 V supply voltage. The fabricated chip shows a Tx average power of -2 dBm, a sensitivity level of -103 dBm at 100 Kbps with PER < 1%, an Rx input $P_{1dB}$ of -11 dBm, and an Rx input IP3 of -2.3 dBm.

• 대한기계학회논문집B
• /
• 제29권9호
• /
• pp.997-1005
• /
• 2005

The extinction characteristics of low strain rate normal gravity (1-g) nonpremixed methane-air flames were studied numerically and experimentally. A time-dependent axisymmetric two-dimensional (2D) model considering buoyancy effects and radiative heat transfer was developed to capture the structure and extinction limits of 1-g flames. One-dimensional (1D) computations were also conducted to provide information on 0-g flames. A 3-step global reaction mechanism was used in both the 1D and 2D computations to predict the measured extinction limit and flame temperature. A specific maximum heat release rate was introduced to quantify the local flame strength and to elucidate the extinction mechanism. Overall fractional contribution by each term in the energy equation to the heat release was evaluated to investigate the multi-dimensional structure and radiative extinction of 1-g flames. Images of flames were taken for comparison with the model calculation undergoing extinction. The two-dimensional numerical model was validated by comparing flame temperature profiles and extinction limits with experiments and ID computation results. The 2D computations yielded insight into the extinction mode and flame structure of 1-g flames. Two combustion regimes depending on the extinction mode were identified. Lateral heat loss effects and multi-dimensional flame structure were also found. At low strain rates of 1-g flame ('Regime A'), the flame is extinguished from the weak outer flame edge, which is attributed to multi-dimensional flame structure and flow field. At high strain rates, ('Regime B'), the flame extinction initiates near the flame centerline due to an increased diluent concentration in reaction zone, which is the same as the extinction mode of 1D flame. These two extinction modes could be clearly explained with the specific maximum heat release rate.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권9호
• /
• pp.427-433
• /
• 2001

A linear ultrasonic motor was designed by a combination of the first longitudinal and fourth bending mode, and the motor consisted of a straight aluminum alloys bar bonded with a piezoelectric ceramic element as a driving element. That is,$L_1-B_4$ linear ultrasonic motor can be constructed by a multi-mode vibrator of longitudinal and bending modes. Linear ultrasonic motors are based on an elliptical motion on the surface elastic body, such as bar or plates. In general, the natural resonance frequency of the stator is used as a driving frequency of the motor which provides a large elliptical motion. The corresponding eigenmode of one resonance frequency can be excited twice at the same time with a Phase shift of 90 degrees in space and time. And the rotation can be reversed by changing the phase between the two signals from sin$\omega$t to cos$\omega$t. Moreover, the tangential force pushes the slider(rotor) and, therefore, determines the thrust and speed of the motor. The experimental results of fabrication motors, bimorph-tyPe motor showed more excellent than unimorph-type. The maximum speed of TBL-200, TBL-300, TBL-400, TBL -220, TBL-310 and TBL-420 motors were 0.12, 0.37, 0.39, 0.14, 0.55 and $0.60ms6{-1}$, respectively. And the efficiency were reported 1.15, 7.9, 6.6, 2.36, 10.1 and 16.5%, respectively. That time, output thrust of the motor was a strong(1~2N) and the weight of stator was a lightness(5~7g).

• 한국통신학회논문지
• /
• 제31권9A호
• /
• pp.892-899
• /
• 2006

본 논문은 IEEE 802.11b-무선 LAM 환경에서 ad-hoc 방식과 infrastructure 방식 사이의 자동 모드 전환 기술을 제안하였다. 또한 관련된 기술을 Linux 환경에 맞추어 설계 및 구현을 하였다. 제안된 메커니즘은 AP (Access Point) 서비스 영역 외곽에 switching area를 정의하고 해당 영역에 머무르는 노드는 AP와 음영지역에 있는 ad-hoc 노드를 연결 가능하게 해준다. 본 기술을 활용하여 기존 IEEE 802.11b 환경에서는 서비스가 불가능한 음영지역에 있는 노드에게도 인터넷 서비스를 제공할 수 있게 한다. 성능 검증은 switching area 감지, 패킷 전달 상황 캡춰, FTP 전송을 통한 처리량 측정으로 이루어졌고 그 결과 제안된 메커니즘기 무선 LAN 서비스를 향상 시킨다는 것을 확인할 수 있었다.