• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.8
• /
• pp.392-401
• /
• 2001

This paper presents the single-stage high power factor AC to DC converter operated in active-clamp mode. The proposed converter is added active-clamping circuit to boost-flyback single-stage power factor corrected power supply. The active-clamping circuit limits voltage spikes, recycles the energy trapped in the leakage inductance, and provides a mechanism for achieving soft switching of the electronic switches to reduce the switching loss. The auxiliary switch of active-clamping circuit uses the same control and driver circuit as the main switch to reduce the additional cost and size. To verify the performance of the proposed converter, a 100W converter has been designed. The proposed converter gives good power factor correction, low line current harmonic distortions, and tight output voltage regulation, as used unity power factor.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.12
• /
• pp.616-623
• /
• 2003

Conventional P/PI speed controller of today's servo drives should be manually tuned the controller switching set-point by trial-and-errors, which may translate the drive system down-time and loss of productivity. The adjustable drive performance is heavily dependent on the quality of the expert knowledge and becomes inadequate in applications where the operating conditions change in a wide range, i.e., tracking command, acceleration/deceleration time, and load disturbances. In this paper, the demands on simple controls/setup are discussed for industry servo drives. Analyzing the frequency content of motor torque command, P/PI control mode switching is automatically performed with some prior knowledge of the mechanical dynamics. The dynamic performance of the proposed scheme assures a desired tracking response curve with minimal oscillation and settling time over the whole operating conditions. For comprehensive comparison of traditional P/PI control scheme, extensive test is carried out on actual servo system.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.12
• /
• pp.2310-2314
• /
• 2007

Stable molecular conformations were calculated for the p-tert-butylcalix[4]arene crown ether bridged at the lower rim with pyridyl unit (1) in the various conformers and their potassium-ion complexes. The structures of three distinct conformations have been optimized using DFT B3LYP/6-31G(d,p) method. Relative stability of free host 1 is in following order: cone (most stable) > partial-cone > 1,3-alternate conformer. For two different kinds of complexation mode, the potassium cation in the crown-ether moiety (cr) has much better complexation efficiency than in the benzene-rings (bz) pocket for all three kinds of conformation of host molecule 1. The relative stability of complex (1+K+) in the cr-binding mode is in following order: partial-cone (most stable) ~ cone > 1,3-alternate conformer.

• Speech Sciences
• /
• v.7 no.2
• /
• pp.85-95
• /
• 2000

In this paper, the H1*-H2* measure is introduced and exact procedures for obtaining the H1*-H2* value are fully specified, The H1*-H2* measure (a corrected difference in dB between the first and second harmonics) has been devised to provide an acoustic correlate of the phonation mode of a vowel following a consonant. With this measure, we can investigate the phonation mode of a vowel that is free from the F1 amplitude perturbation effect caused by the preceding consonant, which is especially salient at the voicing onset position of the vowel. For identical research purposes, on the other hand, the H1-H2 measure (the observed difference in dB between the first and second harmonic) has been employed in many previous studies. This paper compares these two measures by illustrating experimental results of exploring post-release phonation modes of vowels following the different manner classes of stop consonants in Korean $\square$i.e., the tense, lenis, and aspirated stops.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.1
• /
• pp.40-46
• /
• 2005

This paper has investigated the speed sensorless indirect vectorcontrol of a two-phase induction motor to implement adjustable-speed drive for low-power applications. The sliding mode observer estimates rotor speed. The convergence of the nonlinear time-varying observer along with the asymptotic stability of the controller has been analyzed. To define the control action which maintains the motion on the sliding manifold, an "equivalent control" concept is used. It has been simulated and implemented on a sensorless indirect vector drive for 150W two-phase induction motor. The simulation and experimental results demonstrate effectiveness of the estimation method.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.457-458
• /
• 2008

This paper presents an output common mode current compensation method to achieve both constant Gm and constant gain. A conventional rail-to-rail CMOS op-amp with constant Gm was designed by using complementary differential input stage and current compensation skills. But it doesn't operate constant gain, because of output resistance variation. With $0.18{\mu}m$ CMOS process, the simulation results show that the differential gain variation can achieve less than 1.3dB. And a 60dB gain, a 13.5MHz unity gain-frequency, and 1mW power consumption, when operating at 1.8V and 10pF load.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.1
• /
• pp.89-96
• /
• 1995

Lateral p-i-n photodiodes have been fabricated, electrically tested, and incorporated into microwave control circuits such as an optically excited microwave atttenuator and reflection type phase shifter. Circuit design procedures for the loaded-line phase shifter with the optically controlled p-i-n photodiode are presented. The equal loss loading mode presented for the first time for the phase shifter circuits with lossy load allows an equal insertion loss of the phase shifter in both of its phase states. It is found that the insertion loss of the equal loss loading mode phase shifter constructed with the fabricated p-i-n photodiode load are about 3dB for 11.25$^{\circ}$ bit and 1dB for 5.625$^{\circ}$ bit for the frequency range of 2GHz to 11GHz.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.11
• /
• pp.856-862
• /
• 2008

This paper presents the characterization of a continuous magnetophoretic microseparator for separating white and red blood cells from peripheral whole blood cells based on their native magnetic properties. The magnetophoretic microseparator separated the blood cells using a high gradient magnetic separation (HGMS) method without the use of additives such as magnetic beads or probing materials. Experimental results show that the paramagnetic capture mode microseparator can continuously separate out 93.5% of red blood cells and 97.4% of white blood cells from diluted whole blood, and the diamagnetic capture mode microseparator can continuously separate out 89.7% of red blood cells and 72.7 % of white blood cells by using applying an external magnetic flux of 0.2 T using a permanent magnet.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11b
• /
• pp.65-68
• /
• 2005

In this paper, a theoretical study is carried out on the hydroelastic vibration of a rectangular tank wall. It is assumed that the tank wall is clamped along the plate edges. The fluid velocity potential is used for the simulation of fluid domain and to obtain the added mass due to wall vibration. In addition, the vibration characteristics of stiffened wall of the rectangular tank are investigated. Assumed mode method is utilized to the stiffened plate model and hydrodynamic force is obtained by the proposed approach. The coupled natural frequencies are obtained from the relationship between kinetic energies of a wall including fluid and the potential energy of the wall. The theoretical result is compared with the three-dimensional finite element method and then added mass effect is discussed due to tank length and potential mode.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.781-787
• /
• 1999

In this note, we propose two methods of adaptive sliding mode control(SMC) schemes in which fuzzy systems(FS) are utilized to approximate the unknown system functions. In the first method, a FS is utilized to approximate the unknown function f of the nonlinear system $\chi$$^{(n)}$$\chi$＝f(equation omitted), t)＋b(equation omitted), t)u and the robust adaptive law is proposed to reduce the approximation errors between the true nonlinear function and fuzzy approximator, FS. In the second method, two FSs are utilized to approximate f and b, respectively. The robust control law is also designed. The stabilities of proposed control schemes are proved.