• 소성∙가공
• /
• 제26권3호
• /
• pp.162-167
• /
• 2017

The tensile surface residual stress in the multi-pass drawn wire deteriorates the mechanical properties of the wire. Therefore, the evaluation of the residual stress is very important. Especially, the axial residual stress on the wire surface is the highest. Therefore, the objective of this study was to propose an axial surface residual stress prediction model of the multi-pass drawn steel wire. In order to achieve this objective, an elastoplastic finite element (FE) analysis was carried out to investigate the effect of semi-die angle and reduction ratio of the axial surface residual stress. By using the results of the FE analysis, a surface residual stress prediction model was proposed. In order to verify the effectiveness of the prediction model, the predicted residual stress was compared to that of a wire drawing experiment.

• Journal of Welding and Joining
• /
• 제19권1호
• /
• pp.49-57
• /
• 2001

In this study, the residual stress fields of multi-pass welded were analyzed by FEA under various geometrical conditions. In order to estimate the effects of pipe geometries on residual stress distribution, welding processes of each model were performed under the same heat cycles. And then, the influence of cutting off the weld bead on the residual stress redistribution was also estimated. From the results, in the range of t/D=0.05, axial residual stresses on the outer surface of the welded pipe were linearly decreased with pipe diameter increase. On the other hand, hoop residual stresses were not influenced by them. And both axial and hoop residual stresses on the outer surface of the welded pipe were increased with pipe diameter increase. But, when t/D was smaller than 0.05, they were converged in the nearly same value. The maximum residual stresses were generated at around HAZ. It in therefore necessary to consider them in welding design, strength evaluation, and analysis of fracture characteristics.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.90-95
• /
• 2004

In this study, we proposed new method to mitigate tensile welding residual stress for preventing PWSCC in CRDM nozzle. Residual stress analysis using finite element method is performed to confirm benefit of the new method. In case of applying existing method, tensile axial residual stress decrease by about 28% and tensile hoop residual stress decrease by about 33%. In case of applying the new method, tensile axial residual stress decrease by about 32% and tensile hoop residual stress decrease by about 43%. Therefore, we conclude the new proposed method is more effective to prevent PWSCC than existing method.

• 한국정밀공학회지
• /
• 제27권8호
• /
• pp.70-75
• /
• 2010

The aim of this study is to evaluate the axial residual stress in multi-pass drawn high carbon steel wire by using FE analysis and XRD. When FE analysis is applied to evaluate the residual stress in drawn wire of multi-pass drawing process, obtaining the reliable effective stress-strain curve at high strain is very important. In this study, a model, which can express the reliable effective stress-strain curve at high strain, is introduced based on the Bridgman correction and tensile test for multi-pass drawn high carbon steel wires. By using the introduced model, FE analysis was carried out to evaluate the axial residual stress in the drawn wires. Finally, the effectiveness of the FE analysis with the introduced stress-strain relation was verified by the measurement of residual stress in the drawn wires through XRD. As a result, the evaluated residual stress of FE analysis shows good agreement with the measured residual stress.

• 대한기계학회논문집A
• /
• 제34권10호
• /
• pp.1479-1485
• /
• 2010

최근 와이어의 생산성 및 고강도화를 위한 고탄소강의 고속신선으로 인해 와이어 표면의 급격한 온도상승으로 잔류응력이 크게 증가하는 문제점이 발생되고 있다. 와이어의 다단 신선 공정시에는 소성변형과 마찰열에 의하여 와이어 내부의 온도가 더욱 크게 상승하게 된다. 특히, 고속 신선의 경우 마찰에 의한 온도구배가 더욱 크게 되어 와이어 표면층에 축방향 인장 잔류응력을 과도하게 발생시킨다. 따라서, 본 연구에서는 먼저 표면 온도 상승과 축방향 잔류응력과의 관계를 규명한 다음에 와이어의 평형온도 예측 모델을 제안하고, 이를 토대로 표면 온도 상승에 의한 축방향 잔류응력 예측식을 개발하였다. 고탄소강(0.82%C)소재의 다단신선 실험을 통해 얻어진 시편에 대하여 X 선 회절을 이용하여 잔류응력을 측정하여 제안된 예측식을 검증하였다.

• 한국공작기계학회논문집
• /
• 제17권3호
• /
• pp.115-121
• /
• 2008

A knowloedge of the residual stress distribution at circumferential welds can increase the prediction accuracy of a fracture assessment in pipe lines. In this study, in order to predict the residual stress distribution in the circumferential butt-welded pipes were measured, using the hole-drilling strain gauge method. Their practical applications were performed in to two kinds of pipes. As the results, the following characteristics were found. On the inner surface of pipes, the circumferential and axial residual stresses were both tensile near the center line of welding and both of them changed from tensile to compressive as the distance from the center line increased. On the outer surface, however, the circumferential residual stress was shown to be tensile wile the axial residual stress was compressive near the center line of welding, and later they were revered at the region far away from the centerline.

• 대한기계학회논문집A
• /
• 제23권7호
• /
• pp.1173-1181
• /
• 1999

In X-ray stress measurements for uni-directionally deformed surfaces such as grinding, a strongly curved $sin^2{\Psi} diagram, so called $\Psi-splitter, has been observed recently. It has been known that this is caused by the residual shear stress induced in the deformed layer by external forces. In this case it is necessary to consider this enough for ceramics and composite materials with tri-axial stress analysis. However, sufficient studies have not been done about the tri-axial stress analysis of the macro stress and micro. stress on each phase of the composite materials. The result of obtaining is as follows. 1. $\Psi-splitter does not appear in the vertical direction though $\Psi-splitter appears in grinding direction in WC-Co cemented carbides. The reversal of $\Psi-splitter to each phase does not appear. 2. $\Psi-splitter caused in WC-Co cemented carbides has a close relation in dislocation which accumulates in WC phase and phase transformation caused in Co phase. 3. The residual stress on the surface of grinding of each phase is in the state of the compression stress.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1999년도 특별강연 및 추계학술발표대회 개요집
• /
• pp.331-334
• /
• 1999

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.25-30
• /
• 2000

Residual stresses induced in U-bending and tube-to-tubesheet joining processes of PWR's steam generator row-1 tube were measured by X-ray method and Hole-Drilling Method(HDM). The stresses resulting from the Internal pressure and the temperature gradient in the steam generator were also estimated theoretically. In U-bent lesions, the residual stresses at extrados were induced with compressive stress(-), and its maximum value reached -319 MPa in axial direction at ${\psi}=0^{\circ}$ in position. Maximum tensile residual stress of 170MPa was found to be at the flank side at Position of${\psi}=90^{\circ}$, i.e., at apex region. In tube-to-tubesheet fouling methods, the residual stresses induced by the explosive joint method were found to be lower than that by the mechanical roll method. The gradient of residual stress along the expanded tube was highest at the. transition region, and the residual stress in circumferential direction was found to be higher than the residual stress in axial direction. Hoop stress due to an internal pressure between primary and secondary side was analyzed to be 76 MPa and thermal stress was 45 MPa.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.241-245
• /
• 2007

The residual stress in axial stress in the axial direction of the steel filaments has been measured by using a method based on the combination of the focused ion beam (FIB) and high resolution strain mapping program (VIC-2D). That is, the residual stress was calculated from the measured displacement field before and after the introduction of a slot along the steel filaments. The displacement was obtained by the digital correlation analysis of high-resolution scanning electron micrographs, while the slot was introduced by FIB milling with low energy beam. The present measurement revealed that the residual stress within 8% of the magnitude was persistent in the steel filaments fabricated.