• 유변학
• /
• 제7권2호
• /
• pp.110-119
• /
• 1995

본 연구에서는 Upper Convected Maxwll 유체 및 Leonov-like-Giesekus 유체모형 을 이용하여 축대칭 4:1수축을 지나는 점탄서유체의 유동을 수치해석하였다. 이러한 점탄성 유체의 대한 지배방정식이 타원형-쌍곡선형으로 형식변화되므로 이를 적절히 고려할수 있 는 형태의 와도방정식을 이용하여 수치해석을 수행하였다. 와도방정식의 수치해석에서는 형 식에 따른 차분법을 도입하였다. 두 유체모형에 대해서 Weissenberg수를 증가시키면서 탄 성의 효과가 모서리와류의 크기, 응력의 분포 지배방정식의 형식변화에 미치는 영향을 살펴 보았다. 수치해석결과 탄성의 효과가 증가할수록 모서리와류가 커지며, 평면유동의 경우보다 훨씬 큰 모서리와류가 관찰되어 기존의 실험결과와 잘 일치하는 것을 볼수 있었다. 또한 수 치해석 결과로부터 와도방정식의 형식변화를 확인할수 있었다.

• 설비공학논문집
• /
• 제13권6호
• /
• pp.448-454
• /
• 2001

In the present study, the transient axi-symmetric numerical simulation of traffic ventilation induced by a train running through a 15.6km-long tunnel is performed by using over 100,000 computational cells. With train running, three cases of ventilation schemes are simulated, which are the case of ventilation fans turned on, the case of no fan but ventilation shafts open, and the case of no fan and no shaft. Results of the ventilation flow rate are pressure transients are compared for the cases considered.

• 한국철도학회논문집
• /
• 제8권6호
• /
• pp.513-519
• /
• 2005

The Korean Tilting Train eXpress may produced a strong micro-pressure wave in tunnel exit because of large train/tunnel area ration of conventional railways. This micro-pressure wave causes an impulsive noise which is a serious environmental noise pollution near tunnel exit. Tunnel hood can be the method of reducing the micro-pressure wave in tunnel exit. Therefore, parametric studies for tunnel hood are performed with respect to the hood length and size to investigate the effects of the tunnel hood. Also, axi-symmetric unsteady compressible flow solver was used to analyze train-tunnel relative motion. According to the result of numerical analysis, the maximum micro-pressure wave in tunnel exit is reduced by 56% throughout the hood establishment on conventional railways.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2000년도 제15회 학술강연회논문초록집
• /
• pp.20-20
• /
• 2000

2개의 경사 충격파와 하나의 수직 충격파로 초음속 유동을 압축하는 초음속 공기 흡입구의 수치적 연구를 수행하였다. 지배방정식으로는 Navier-Stokes방정식을 사용하였고 난류모델로는 SST 모델을 사용하였다. 지배방정식의 점성항 계산에는 중심차분법을 사용하였고 대류항 계산에는 풍상차분법인 Roe의 FDS기법을 MUSCL기법과 결합하여 이용하였다. 유한 체적법을 이용하여 차분된 방정식은 LU분할 기법을 이용한 완전 내재적 방법으로 2차 정확도 시간 적분으로 비정상 과정의 연구를 수행하였다. 흡입구 배압을 정해주어야 하는 어려움을 해결하기 위해 흡입구 후면에 노즐을 달고 노즐의 면적을 조절하여 배압이 형성되도록 하였다.(중략)

• International Journal of Fluid Machinery and Systems
• /
• 제2권4호
• /
• pp.295-302
• /
• 2009

The flow in the draft tube cone of Francis turbines operated at partial discharge is a complex hydrodynamic phenomenon where an incoming steady axisymmetric swirling flow evolves into a three-dimensional unsteady flow field with precessing helical vortex (also called vortex rope) and associated pressure fluctuations. The paper addresses the following fundamental question: is it possible to compute the circumferentially averaged flow field induced by the precessing vortex rope by using an axisymmetric turbulent swirling flow model? In other words, instead of averaging the measured or computed 3D velocity and pressure fields we would like to solve directly the circumferentially averaged governing equations. As a result, one could use a 2D axi-symmetric model instead of the full 3D flow simulation, with huge savings in both computing time and resources. In order to answer this question we first compute the axisymmetric turbulent swirling flow using available solvers by introducing a stagnant region model (SRM), essentially enforcing a unidirectional circumferentially averaged meridian flow as suggested by the experimental data. Numerical results obtained with both models are compared against measured axial and circumferential velocity profiles, as well as for the vortex rope location. Although the circumferentially averaged flow field cannot capture the unsteadiness of the 3D flow, it can be reliably used for further stability analysis, as well as for assessing and optimizing various techniques to stabilize the swirling flow. In particular, the methodology presented and validated in this paper is particularly useful in optimizing the blade design in order to reduce the stagnant region extent, thus mitigating the vortex rope and expending the operating range for Francis turbines.

• 한국항공우주학회지
• /
• 제33권8호
• /
• pp.92-98
• /
• 2005

스크린은 유동저항을 일으켜 유동의 난류, 속도 및 압력 특성을 변화시킬 수 있으며, 이에 따라 유동제어 방법으로 널리 사용되어 왔다. 과거 관련 분야 연구들은 마하수가 0.3에서 0.7 사이의 유동에 제한되어 왔고, 초음속 유동에서 나타나는 충격파 구조에 대한 연구는 수행되어진 바 없다. 따라서 본 연구에서는 철선으로 엮어진 스크린 후방에서 나타나는 축대칭 초음속 제트유동장에 대한 실험적 관찰이 이루어졌다. 다양한 제트유동 팽창조건에 대하여 스크린 후방에서 연속 및 순간광원을 이용한 쉴리렌 유동가시화와 피토압력/유동소음 측정이 이루어졌다. 노즐 출구에 설치된 스크린의 다공도와 설치 기울기 변화에 따른 영향도 관찰되었으며, 얻어진 결과는 스크린이 설치되지 않은 경우와 서로 비교되었다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.559-564
• /
• 2008

A prediction of binary droplets collision is important in the formation of falling drops and the evolution of sprays. The droplet velocity, impact parameter and drop-size ratio have influence on the interaction of the droplets. By the effect of these parameter, the collision processes are generated with the complicated phenomena. The droplet collision can be classified into four interactions such as the bouncing, coalescence, reflexive separation and stretching separation. In this study, the two-phase flow of the droplet collision was simulated numerically by using the Level Set method. 2D axi-symmetric simulations on the head-on collisions in the coalescence and reflexive separation, and 3D simulation on the off-center collisions in the coalescence and stretching separation were performed. These numerical results showed good agreements with the experimental and analytical results. For tracking the identity of droplets after the collision, transport equation for the volume fraction of the each initial droplet were used. From this, the identities of droplets were analyzed on the collision of droplets having different size.

• 대한기계학회논문집B
• /
• 제33권2호
• /
• pp.93-100
• /
• 2009

Characteristics of micro-sonic/supersonic axi-symmetric jet impinging on a flat plate with a pre-drilled hole were both experimentally and numerically studied, to observe the role of assist-gas jet to eject melted materials from the cut zone in the laser machining. For various Mach numbers of the nozzle and the total pressures of the assist gas, detailed impinging jet flow structures over the plate and the variations of mass flux through the pre-drilled hole were observed. It was found that the present experimental and numerical results show a good agreement, which proves the accountability of the present work. From the present study, it was also observed that the mass flow rate through the hole was closely related with the total pressure loss caused by the Mach disc on the work piece, and that supersonic nozzle could perform more efficient roles as blowing the assist-gas jet in the laser machining, as compared to sonic nozzles.

• 한국자동차공학회논문집
• /
• 제6권2호
• /
• pp.12-20
• /
• 1998

Exter ballistics of a typical high-speed projectile is studied through a flow-visualization experiment and an unstructured grid Navier-Srokes computation. Experiment produced a schlieren photograph that adequately shows the characteristic features of this complex flow, namely two kinds of oblique cone shocks and turbulent wake developing into the downstream. A hybrid scheme of finite volume-element method is used to simulate the compressible Reynolds-Averaged Navier-Stok- es solution on unstructured grids. Osher's approximate Riemann solver is used to discretize the cinvection term. Higher-order spatial accuracy is obtained by MUSCL extension and van Albada ty- pe flux limiter is used to stabilize the numerical oscillation near the solution discontinuity. Accurate Gakerkin method is used to discretize the viscous term. Explict fourth-order Runge-Kutta method is used for the time-stepping, which simplifies the application of MUSCL extension. A two-layer k-$\varepsilon$ turbulence model is used to simulate the turbulent wakes accurately. Axisymmetric folw and two-dimensional flow with an angle of attack have been computed. Grid-dependency is also checked by carrying out the computation with doubled meshes. 2-D calculation shows that effect of angle of attack on the flow field is negligible. Axi-symmetric results of the computation agrees well with the flow visualization. Primary oblique shock is represented within 2-3 meshes in numerical results, and the varicose mode of the vortex shedding is clearly captured in the turbulent wake region.

• 한국추진공학회지
• /
• 제17권3호
• /
• pp.37-46
• /
• 2013

최근, micro shock tube는 Micro combustion, Micro propulsion, Particle delivery systems 등과 같은 다양한 공학응용분야에서 사용 되고 있다. Micro shock tube 에서 일어나는 유동 특성은 아주 작은 레이놀즈수 와 높은 누센수의 영향으로 인해 잘 알려진 기존의 macro shock tube 유동 특성과 상당한 차이가 나타난다. 또한 기존의 많은 shock tube의 순간적 과정으로 간주되는 격막파막 과정은 micro shock tube의 격막 근처의 유동장과 충격파 형성을 결정하는 중요한 요인이 될 것이다. 본 논문에서는 micro shock tube를 모사하기 위해 축 대칭, Maxwell's 슬립속도 조건과 온도 변화 경계 조건을 적용하여 수치 해석을 수행 하였다. 또한 유동장과 충격파 형성에 대한 유한 파막 과정의 영향을 자세히 조사 하였고, 결과로부터 충격파 강도는 micro shock tube를 통해 전파됨에 따라 급격히 감소하였다.