• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.6
• /
• pp.314-319
• /
• 2013

Fabrication of nanocomposite material for the $Fe_2O_3-Al$ system by mechanical alloying (MA) has been investigated at room temperature. It is found that ${\alpha}-Fe/Al_2O_3$ nanocomposite powders in which $Al_2O_3$ is dispersed in ${\alpha}-Fe$ matrix are obtained by mechanical alloying of $Fe_2O_3$ with Al for 5 hours. The change in magnetization and coercivity also reflects the details of the solid state reduction process of hematite by pure metal of Al during mechanical alloying. Densification of the MA powders was performed in a spark plasma sintering (SPS) machine using graphite dies at $1000^{\circ}C$ and $1100^{\circ}C$ under 60 MPa. Shrinkage change after SPS of MA'ed sample for 5 hrs was significant above $700^{\circ}C$ and gradually increased with increasing temperature up to $1100^{\circ}C$. X-ray diffraction result shows that the average grain size of ${\alpha}-Fe$ in ${\alpha}-Fe/Al_2O_3$ nanocomposite sintered at $1100^{\circ}C$ is in the range of 180 nm. It can be also seen that the coercivity (Hc) of SPS sample sintered at $1000^{\circ}C$ is still high value of 88 Oe, suggesting that the grain growth of magnetic ${\alpha}-Fe$ phase during SPS process tend to be suppressed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.2
• /
• pp.59-65
• /
• 2006

Al-doped and F-doped ZnO (ZnO : Al & ZnO : F) thin films were coated onto glass substrate by sol-gel method. These films showed c-axis orientation in common, but different I(002)/[I(002) + I(101)] and FWHM (full width at half-maximum). In particular, the grain size of the ZnO : Al films decreased with the increase in the Al-doping concentration, while for the ZnO : F films the grain siae increased up to F 3 at% and then decreased. For the electrical properties, Hall effect measurement was used. The resistivity of the ZnO : Al films and the ZnO : F films were, respectively, $2.9{\times}10^{-2}{\Omega}cm$ at Al 1 at% and $3.3{\times}10^{-1}{\Omega}cm$ at F 3 at%. Moreover compared with ZnO:Al films, ZnO:F films have lower carrier concentration (ZnO : Al $4.8{\times}10^{18}cm^{-3}$, ZnO : F $3.9{\times}10^{16}cm^{-3}$) and higher mobility (ZnO : Al $45cm^2/Vs$, ZnO : F $495cm^2/Vs$). For average optical transmittances, ZnO : Al thin films have $86{\sim}90%$ and ZnO : F films have $77{\sim}85%$ comparatively low.

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.85-91
• /
• 2005

$SnO_2$ films were prepared at room temperature under a $(CH_3)_4Sn-H_2-O_2$ atmosphere in order to obtain transparent conductive polymer by using ECR-MOCVD (Electron Cyclotron resonance -Metal Organic Chemical Vapor Deposition) system. The electrical properties of the films were investigated as function of process parameters such as deposition time, microwave power, magnetic current power, magnet/showering/substrate distance and working pressure. An increase in microwave power and magnetic current power brought on $SnO_2$ film formation with low electric resistivity. On the other hand, the effects of process parameters described above on optical properties were insignificant in the range of our experimental scope. The transmittance and reflectance of the films prepared by the ECR-MOCVD exhibited their average values of 93-98% at wave length range of 380-780 nm and 0.1-0.5%, respectively. The grain size of the $SnO_2$ films that are also insensitive with the process parameters were in the range of 20-50 nm. On the basis of experimental data obtained in the present study, electrical resistivity of $7.5{\times}10^{-3}ohm{\cdot}cm$, transmittance of 93%, and reflectance of 0.2% can be taken as optimum values.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.6
• /
• pp.493-501
• /
• 2000

The microstructure and electrical properties of ZnO-Pr$_{6}$/O$_{11}$-CoO-Er$_{2}$/O$_{3}$ based varistors were investigated with Er$_{2}$/O$_{3}$ additive content of the range 0.0 to 2.0 mol%. Most of the added Er$_{2}$/O$_{3}$ were segregated at the nodal points and grain boundaries and it coexisted with Pr$_{6}$/O$_{11}$ in the bulk intergranular layer. The average grain size was decreased in the range of 7.44 to 5.62${\mu}{\textrm}{m}$ at 130$0^{\circ}C$ and 18.36 to 9.11 at 135$0^{\circ}C$ with increasing Er$_{2}$/O sub 3/ additive content. The density of ceramics was in the range 4.87 to 5.08 g/cm$^3$ at 130$0^{\circ}C$ and 5.35 to 5.62 g/cm$^3$at 135$0^{\circ}C$. At 130$0^{\circ}C$ the varistors without Er$_{2}$/O$_{3}$ exhibited 29.66 in the nonlinear exponent and 28.23 $\mu$A in the leakage current whereas the varistors with 0.5 mol% Er$_{2}$/O$_{3}$ exhibited a high nonlinearity which is 52.78 in thenonlinear exhibited and 9.75 $\mu$A in the leakage current. At 135$0^{\circ}C$ the varistors without Er$_{2}$/O$_{3}$ exhibited a very poor nonlinearity indicating 2.08 in the nonlinear exponent and 133.79 $\mu$A in the leakage current whereas the varistors with 1.0mol% Er$_{2}$/O$_{3}$ exhibited a relatively high nonlinearity which is 36.79 in the nonlinear exponent and 5.92 $\mu$A in the leakage current. Therefore Er$_{2}$/O$_{3}$ was additive which greatly improve the nonlinearity. It is believed that ZnO-0.5 mol% Pr$_{6}$/O$_{11}$-1.0 mol% CoO-0.5 mol% Er$_{2}$/O$_{3}$ based ceramicss will be usefully used as a basic composition to develop the advanced pr$_{6}$/O$_{11}$-based ZnO varistors.ristors.ristors.

• Korean Journal of Materials Research
• /
• v.9 no.7
• /
• pp.753-759
• /
• 1999

The microstructure and electrical properties of ZNR that W $O_3$ is added in the range 0.5~4.0mol%, were investigated. The major part of W $O_3$ were segregated at the nodal point and W-rich phase was formed. Three crystalline phases, such as W-rich phase (W $O_3$), Bi-rich phase (B $i_2$W $O_{6}$ ), and spinel phase (Z $n_{2.33}$S $b_{0.67}$ $O_4$) were confirmed to be co-existed at the nodal point The average grain size increased in the range 15.5~29.9$\mu\textrm{m}$ with increasing W $O_3$ additive content. Consequently. W $O_3$ acted as a promotion additive of grain growth. As the W $O_3$ additive content increases. the varistor voltage and the nonlinear exponent decreased in the range 186.82~35.87V/mm and 20.90~3.34, respectively, and the leakage current increased in the range of 22.39~83.01 uh. With increasing W $O_3$ additive content, the barrier height and the density of interface states decreased in the range 1.93~0.43eV and (4.38~1.22)$\times$10$^{12}$ $\textrm{cm}^2$, respectively. W $O_3$ acted as an acceptor additive due to the donor concentration increasing in the range (1.06~0.38)$\times$10$^{18}$ /㎤with increasing W $O_3$ additive content.t.t.

• The Korean Journal of Quaternary Research
• /
• v.9 no.1
• /
• pp.33-42
• /
• 1995

우리나라의 서해(West Sea)는 일명 황해(Yellow Sea)라고 일컬어지는 약 40여 m의 평균 수심을 갖는 대륙붕 해저지형 분지에 의하여 지배되는 전형적 육연해이다, 그런데 이 바다는 중심부(황해의 중심부)를 기준으로 하여 중국 대륙의 산동반도에서 양가강 하구에 이르는 서부 해안을 가지며 북부에는 발해만의 해안이 있고 동부에는 서해(황해) 특유의 넓 은 조수환경(tidal environment)과 조수해안이 발달한다. 그러나 남쪽으로는 북서태평양과 연결된다. 한국 서해안이 평균 4m 이상의 조차(tidal range)를 나타내는 조간대 조수환경이 며 조간대 해저지형(intertidal morphology)이 전형적인 퇴적층(체)에 의하여 지배되는 여러 가지 특징을 나타낸다. 서해안 조수환경은 네델란드, 독일 또는 지배되는 여러 가지 특징을 나타낸다. 서해안 조수환경은 네델란드 독일 또는 미국의 경우와 같이 연구가 잘되어 세계 적으로 널리 알려진 소위 barrier island system and tidal depositional environments와는 크 게 다른 퇴적과정과 환경이다. 경기도 남양만의 조수 환경의 경우, 조간대 해저지형 요소인 조류로(tidal channel)와 조간대 정규해저(intertidal zone proper)에 관한 동력적 퇴적과정 연 구결과 조간대 특유의 lateral sedimentation 과 vertical sedimentation 2가지 퇴적과정중 후 자의 퇴적과정이 우세한 것으로 밝혀졌고 이러한 퇴적과정의 진행이 매우 안정한 지속성을 가지는 것이 특징이다, 이러한 퇴적과정의 조간대 퇴적물의 쇄설 입자는 약 20% 미만의 모 래(sand) 입자 50~70%의 실트(silt) 와 점토(clay) 입자가 20~30%에 달하는 입자조직 (grain texture)의 퇴적상을 나타낸다. 결과적으로 조간대의 동력적인 조수수괴의 수위(level of tidal water)는 평균 만조선과 평균 저조선으로 한정되며 이것은 퇴적과정과 퇴적작용의 조정(control) 요인으로 조간대 퇴적상의 발달과 분포에 큰 영향을 미친다, 예를들면 남양만 등의 대부분의 서해안 조간대 표층 퇴적상(녁\ulcorner미 sedimentary faci-es)은 만조선에서 간조 선에 가까울수록 조립화현상(coarsening trend)을 나타낸다. 이러한 퇴적상 변화는 저조선에 서 만조선으로의 조간대 지형과 주조수로의 지형.수력학적 특성이 다음과 같기 때문이다. a) a general decrease in width b) a general decrease in depth c) a general decrease in maximum and average current velocities d) a general increase in contents of suspended mud e) a general decrease in grain size of the bottom sand and an increasing abundance of muddy deposits. 우리나라 서해안 조간대 퇴적층(체)의 수직 층서(vertical stratigraphy)는 지난 3여년동안의 수십개의 vibracoring(주상시추)에 의하여 매우 흥미롭고 중요하게 밝혀지고 있는바 이것은 현세(Holocene)와 선현세(preHolocene: 11000 years BP)의 오랜시간 경과에 따른 조수환경 변화의 수직퇴적 과정과 기후 해수면 변화의 현상에 원인이 있다고 해석된다.(박용안 외, 1992-1995)결과적으로 서해안 조수퇴적체(층)의 분지주변(basim margin)진화과정이 밝혀지 고 있다.

• Korean Journal of Materials Research
• /
• v.3 no.5
• /
• pp.497-504
• /
• 1993

Effects of $Ta_2O_5,ZrO_2$ and $SiO_2$ addition on magnetic properties of 0.02wt%$Bi_2O_3$ and 0 . 0 5 wt%$CaCO_3$ doped Mn-Zn ferrites(58.5mol% $Fe_2O_3$, 25.5 mol% ZnO) were investigated. E:lectrlcal resistivity and magnetic properties such as the initial permeability($\mu_i$), loss factor(tan$\delta$), coercive force Hc(m0c) were measured. With lncreasing $Ta_2O_5$ and $ZrO_2$ addition, the following effects were observed: I ) Decreasing of the average grain size; 2) lncreasing of the electrical resistivity and initial permeability; 3) Ilecreasmg of loss factor values. (very low loss esprcially at high frequency region) ; 4 ) Fine and uniform microsrructures were obtamed at O.lwt% nddecl samples. In case of $SiO_2$ addition, anomalous grain growth and degradation of magnetic properties were observed. The obtained maximum initial permeability value was 6260 at IOkHz. $25^{\circ}C$ from 0.02wt%$Bi_2O_3$. 0.05wt%$CaCO_3$, 0.lwt%$Ta_2O_5$ added sample, the corresponded relative loss factor (tan$\delta /\mu_i$)for the sample was $4.2 \times 10^{-6}$.

• Journal of the Korean earth science society
• /
• v.40 no.1
• /
• pp.37-45
• /
• 2019

In spite of continued nourishments, Haeundae Beach in Busan has been suffering from erosion, this being caused by the increased wave energy due to global warming and intermittent typhoon reported by previous works. In the meantime, the typhoon Chaba hit Basan in October 2016. In order to investigate the effects of the typhoon in beach erosion and how fast the beach recovered after the typhoon, repeated beach profiling using a VRS-GPS system was carried out, and the grain size analyses for surface sediments sampled on the beach were conducted. Immediately after the typhoon invasion, Haeundae beach was eroded by 1.4 m in average height. The mean high tide lines were retreated back by 12 m, and beach slope became gentler from $3.8^{\circ}$ to $1.7^{\circ}$. The mean grain sizes of surface sediments became coarser from $1.6{\Phi}$ to $1.2{\Phi}$ after two months, and the sorting well sorted. After two months of typhoon landfall, the mean high tide lines have recovered by 85%, and the beach topography almost recovered. This suggests that the impact of typhoons on Haeundae beach erosion is negligible, and the relaxation time is shorter than that of other beaches.

• Korean Journal of Materials Research
• /
• v.14 no.1
• /
• pp.28-34
• /
• 2004

IN 738LC, the major material for gas-turbine for power generation, was heat treated at $750^{\circ}C$, $850^{\circ}C$, $950^{\circ}C$ for 1000, 2000, and 4000 hrs and the microstructural evolution and mechanical properties were examined using optical microscope, XRD, SEM/EDS. The results showed ${\gamma}$', the main strengthening elements in this alloy, was about 300 nm in size and was about 56% by area fraction in as-cast samples. The area fraction of ${\gamma}$' peaked at 2000 hours at $750^{\circ}C$. The average diameter of the ${\gamma}$' which was about 300 nm at ascast specimen increased to about 1 $\mu\textrm{m}$ after heat treatment at $950^{\circ}C$ for 4000 hrs. Carbides were formed at dendrite, cell or grain boundaries which was ascribed to the segregation caused by solute redistribution during solidification. It was found that MC type carbides formed at low temperature, whereas carbides of $M_{23}$ /$C_{ 6}$/ type formed at higher temperature or at longer degradation. The hardness and impact energy decreased as the heat treatment temperature or time of retention increased, which was inaccrodance with the area fraction of ${\gamma}$'.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.1
• /
• pp.12-16
• /
• 2020

Indium tin oxide (ITO) films were prepared onto transparent polyimide (PI) substrates by RF magnetron sputtering at room temperature. The deposited ITO films were heat-treated at various temperatures (50, 100, 150, and 200℃). The effect of post heat-treatment temperature on structural, electrical and optical properties of ITO films were investigated. It was found that the as-deposited ITO films were amorphous and the degree of crystallinity and the grain size increased with an increasing heat-treatment temperature, which led to the increase in carrier concentration and mobility. The electrical resistivity of as-deposited ITO films was 2.73 × 10^-3 Ω·cm. With the heat-treatment temperature increasing from 50 to 200℃, the electrical resistivity decreased from 2.93 × 10^-3 to 1.21 × 10^-4 Ω·cm. The average transmittance (400~800 nm) of the ITO deposited PI substrates was decreasing with post heat-treatment temperature and was above 81 % for the temperatures 50~150℃ and decreased considerably to 78 % at 200℃.