• 대한전기학회논문지
• /
• 제45권3호
• /
• pp.341-351
• /
• 1996

The values for the average and rms currents in a three-level PWM inverter are required in order to select the various components such as power semiconductor devices, capacitors and reactors of inverter circuit. And those are very useful for the designing of the heat sink. In this paper, therefore, the simple current equations are proposed for a three-level PWM inverter. Analysis of inverter current waveforms indicate that the average and rms inverter currents are dependent on the load power factor and PWM modulation index (Ma). Error analysis and experiment results verify the effectiveness of the proposed current equations. (author). refs., figs., tabs.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.448-452
• /
• 1997

Theoretical average current and rms current equations are solved using the analytical method in the 3phase voltage-fed inverter. Experimental switch current equations are established by simulation and compared with theoretical equations. As a result of analysis, average and rms currents of switch devices are represented by a function as power factor and modulation index. Especially, equations of this paper are represented as a function of a single factor(K) equal to the product of the power factor and modulation index. Method that can find current levels of switch devices for inverter design and conduction loss of inverter in a simple and accurate manner is presented. Influences of modulation method on switch current are also studied.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.506-511
• /
• 1998

This paper gives and analytical expression of the average and rms currents of switching devices in volt-age-fed PWM inverters. It is shown that the device currents are represented by a function of the power factor of the load and the normalized output voltage of the inverter. The validity of the derived formulas is confirmed with simulation and experiment, showing that the modulation method has a minor effect on the characteristics of the device current.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 연구회 합동 학술발표회 논문집
• /
• pp.18-22
• /
• 1998

A PWM inverter with an induction motor often has a problem with a high frequency leakage current that flows through stray capacitor between stator windings and a motor frame to ground. This paper presents an equivalent circuit for high frequency leakage currents in PWM inverter feeding an induction motor, which forms an LCR series resonant circuit. A conventional common mode ckoke or reactor in series between the ac terminals of a PWM inverter and those of an ac motor is not effective to reduce the rms and average values of the leakage current, but effective to reduce the peak value. Furthermore, this paper proposes a leakage current damper which is different in damping principle from the conventional common mode choke. It is shown theoretically and experimentally that the leakage current damper is able to reduce the rms value of the leakage current to 25%, where the core used in the leakage current damper is smaller than that of the conventional common-mode choke

• Corrosion Science and Technology
• /
• 제20권5호
• /
• pp.231-241
• /
• 2021

The objective of this study was to evaluate total current under steady-state conditions for a material undergoing corrosion using the electrochemical frequency modulation (EFM) technique, taking into account the presence of solution resistance and double layer capacitance. The analysis involving linearization of the Tafel curve allowed for the estimation of corrosion parameters. Results showed that the output signal was dependent on fundamental frequencies and their multiples. In addition, the output signal almost manifested itself at frequencies that were sums of fundamental frequencies of the applied sinusoidal signal. The harmonics calculated showed a significant shift from the principal frequency of input signals. The investigation involved the influence of corrosion current and anode-to-cathode Tafel slope ratio on faradaic and non-faradaic currents (including the average and RMS). The model presented showed both qualitative and quantitative improvements over the previously developed EFM technique that ignored the influence of solution resistance and the double layer capacitance while assuming the applied DC potential corresponded to the corrosion potential of the corroding material.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.390-394
• /
• 2001

A dynamic simulation model for the brush less dc (BLDC) motor drives using Matlab is presented. In this model, an entire BLDC motor drive, including power conversion unit, BLDC motor, and speed/torque control system, is investigated. Especially, the PWM inverter is modeled using switching function concept, so that the detailed voltage and current waveforms, such as line-to-line voltages, inverter input current, ac line current, and switch/diode currents, can be obtained and average/rms ratings of the components can be easily calculated. Also, the proposed model is made into modular blocks and it can be easily extended to other ac motor applications with a little modification. The detailed modeling method is explained and its actual implementation is described. The validity of the proposed model is verified by various simulation results.

• Journal of Power Electronics
• /
• 제15권3호
• /
• pp.685-694
• /
• 2015

The power loss of the controllable switches in modular multilevel converter (MMC) HVDC transmission systems is an important factor, which can determine the design of the operating junction temperatures. Due to the dc current component, the approximate calculation tool provided by the manufacturer of the switches cannot be used for the losses of the switches in the MMC. Based on the enabled probabilities of each SM in an arm, the current analytical models of the switches can be determined. The average and RMS currents can be obtained from the corresponding current analytical model. Then, the conduction losses can be calculated, and the switching losses of the switches can be estimated according to the upper limit of the switching frequency. Finally, the thermal resistance model of the switches can be utilized, and the junction temperatures can be estimated. A comparison between the calculation and PSCAD simulation results shows that the proposed method is effective for estimating the junction temperatures of the switches in the MMC.