• Special Issue of the Society of Naval Architects of Korea
• /
• 2011.09a
• /
• pp.112-116
• /
• 2011

The noise analysis is usually carried out in the early structure design stage for the main areas in a vessel such as an accommodation, an engine room, HVAC System and etc. If the analysis results are higher than the noise limits based on guideline, appropriate countermeasures are established to reduce noise levels and applied to the vessel. But excessive noise induced the main or auxiliary equipment and high pressure steam system is very difficult to check in the initial design stage, and local noise problems frequently appear in actual vessels. This paper deals with excessive noise of the engine control room on LNG carrier. It includes the cause analysis of excessive noise, the countermeasure, and verification. Also, it proves suitability of the countermeasure through the on-board test.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.6
• /
• pp.466-476
• /
• 2010

In this paper, for the notebook adapter with power level below approximately 60W, a novel LLC resonant converter preceded by diode rectifier with a capacitor filter is presented. Due to the switching operation of the auxiliary switching device, the proposed LLC resonant converter can deliver power with the high efficiency characteristics from the universal line(110VAC/220VAC) and load conditions. The operating schemes on the proposed converter are analyzed and described. A 60W prototype product is built, tested and verified.

• Structural Engineering and Mechanics
• /
• v.55 no.5
• /
• pp.1055-1086
• /
• 2015

The dynamic response of two-dimensional unbounded domain on the rigid bedrock in the time domain is numerically obtained. It is realized by the modified scaled boundary finite element method (SBFEM) in which the original scaling center is replaced by a scaling line. The formulation bases on expanding dynamic stiffness by using the continued fraction approach. The solution converges rapidly over the whole time range along with the order of the continued fraction increases. In addition, the method is suitable for large scale systems. The numerical method is employed which is a combination of the time domain SBFEM for far field and the finite element method used for near field. By using the continued fraction solution and introducing auxiliary variables, the equation of motion of unbounded domain is built. Applying the spectral shifting technique, the virtual modes of motion equation are eliminated. Standard procedure in structural dynamic is directly applicable for time domain problem. Since the coefficient matrixes of equation are banded and symmetric, the equation can be solved efficiently by using the direct time domain integration method. Numerical examples demonstrate the increased robustness, accuracy and superiority of the proposed method. The suitability of proposed method for time domain simulations of complex systems is also demonstrated.

• Nuclear Engineering and Technology
• /
• v.45 no.7
• /
• pp.961-968
• /
• 2013

The Arabian Gulf region has one of the highest ocean temperatures, reaching above 35 degrees and ambient temperatures over 50 degrees in the summer. Two nuclear power plants (NPP) are being introduced in the region for the first time, one at Bushehr (1,000 MWe PWR plant from Russia), and a much larger one at Barakah (4X1,400 MWe PWR from Korea). Both plants take seawater from the Gulf for condenser cooling, having to modify the secondary/tertiary side cooling systems design by increasing the heat transfer surface area from the country of origin. This paper analyses the secondary side of a typical PWR plant operating under the Rankine cycle with a simplified thermal-hydraulic model. Parametric study of ocean cooling temperatures is conducted to estimate thermal efficiency variations and its associated design changes for the secondary side. Operational safety is reviewed to deliver rated power output with acceptable safety margins in line with technical specifications, mainly in the auxiliary systems together with the cooling water temperature. Impact on the Gulf seawater as the ultimate heat sink is considered negligible, affecting only the adjacent water near the NPP site, when compared to the solar radiation on the sea surface.

• Journal of the Korean housing association
• /
• v.12 no.3
• /
• pp.41-49
• /
• 2001

This study attempts to present a new interpretation of the Jeju province Waga, authorized as Jeju province Folklore, in the context of lifestyles of residents distinctive in the Jungji, Chatbang, and Gopang system. Study results uncovered that (1) only one Jungji, a traditional house kitchen, exists in one house boundary, in the form of detached building in the 4 units of Gaok (K-2 Gaok, K-3 Gaok, C-1 Gaok, and C-2 Gaok) (2) Chatbang had multifaced-functions; as a place for diet for mistress and children, a place for preparing meals for a mister who diet in the room, and as an auxiliary meal-preparation facility in time of domestic celebration day. (3) Gopang was mostly a place for grain storage, and K-3 Gaok has one unit, K-1 Gaok, C-1 Gaok, and C-2 Gaok had 2 units, and K-2 Gaok and H Gaok had 3 untis of Gopang. (4) Jungji and Chatbang were correlated for meal preparation and diet while activity-line of flow was divided each other. (5) Jungji and Gopang were located at the opposite edges of of each house, revealing no consideration of indoor activities. (6) The ratios of space of Jungji, Chatbang and Gopang out of the whole house space were, average 23% in the case of Jungji located in the inner house, and average 37% in the case of Jingji located in the detached building, average 14% larger in the case of detached Jungji system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.4
• /
• pp.382-395
• /
• 2011

In this paper, for adapter with power level below approximately 60W, a novel LLC resonant converter preceded by diode rectifier with a capacitor filter is presented. Due to the switching operation of the auxiliary switching device, the proposed LLC resonant converter can deliver power with the high efficiency characteristics from the universal line($110V_{AC}$/ $220V_{AC}$) and load conditions. The operating schemes on the proposed converter are analyzed and described. A 60W prototype product is built, tested and verified.

• Medical Lasers
• /
• v.8 no.2
• /
• pp.43-49
• /
• 2019

The plume produced by vaporizing tissue with a laser contains a variety of contaminants called laser-generated air pollutants (LGACs). LGACs consist of a mixture of toxic gas components, biomicroparticles, dead and living cells, and viruses. Toxic odors and thick smoke from surgical incisions and the coagulation of tissues can irritate eyes and airways, as well as cause bronchial and pulmonary congestion. Because of the potential risk of the smoke, it is advisable to appropriately remove it from the surgical site. We recommend using a smoke evacuator to remove the smoke. Suction nozzles should be placed as close as possible to the surgical site in a range of 2 cm or less. In-line filters should be used between the inlet and outlet of the surgical site. All air filtration devices should be capable of removing particles below 0.1 microns in size. The filter pack should be handled according to infection control procedures in the operating room. The laser mask can be an auxiliary protective device if it is properly worn. Some smoke inhaled under the nose wrap or over the side of the mask will not be filtered. As in electrosurgical operations, a suitable mask should be worn while smoke is present.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.1
• /
• pp.77-83
• /
• 2011

In this thesis, 50W Doherty amplifier was designed and implemented for Beyond 3G's repeater and base-station. Auxiliary amplifier of doherty amplifier was implemented by Gate bias control circuit. Though gate bias control circuit solved auxiliary's bias problem, output characteristics of doherty amplifier was limited. To enhance the output characteristic relativize Drain control circuit And To improve power efficiency make 3-way Doherty power amplifier. therefore, 3-way GDCD (Gate and Drain bias Control Doherty) power amplifier is embodied to drain bias circuit for General Doherty power amplifier. The 3-way GDCD power amplifier composed of matching circuit with chip capacitor and micro strip line using FR4 dielectric substance of specific inductive capacity(${\varepsilon}r$) 4.6, dielectric substance height(H) 30 Mills, and 2.68 Mills(2 oz) of copper plate thickness(T). Experiment result satisfied specification of amplifier with gains are 57.03 dB in 2.11 ~ 2.17 GHz, 3GPP frequency band, PEP output is 50.30 dBm, W-CDMA average power is 47.01 dBm, and ACLR characteristics at 5MHz offset frequency band station is -40.45 dBc. Especially, 3-way DCHD power amplifier showed excellence efficiency performance improvement in same ACLR than general doherty power amplifier.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.5
• /
• pp.947-954
• /
• 2009

This paper proposed a new balanced power amplifier using the reflected input of conventional balanced power amplifiers composed of branch line hybrid coupler. In general, the single-ended amplifier in balanced amplifiers does not have the perfect matching, so the reflected input power, in other words the leakage power, is terminated conventionally at the isolation port of hybrid coupler. However in this work, the leakage power is injected into the auxiliary amplifier, and its output power is combined to the output power of balanced amplifier. Therefore output power, efficiency, and 2-tone IMD3 performances of the proposed balanced amplifier are highly improved compared to the conventional balanced amplifier. For the verification of the proposed balanced amplifier, a conventional balanced amplifier and the proposed balanced amplifier are designed, fabricated and measured, and the measured results are compared. The proposed balanced amplifier shows the improvement in the output power(Pout), power added efficiency (PAE), and 2-tone IMD3 by 3dB, 5.2%, and $5{\sim}10dBc$, respectively, from the measurement.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.5
• /
• pp.101-107
• /
• 2017

Over-break, which is excavated larger than planned line at tunnel excavation, is inevitable due to the nature of blasting. But regarding the bottom of the foundation, most of the domestic ordering organizations pay only 10 cm thick filled concrete when pouring concrete due to over-break. In accordance, the construction cost will increase greatly if all the depths of the designed over-break are filled only with concrete. When tunnel excavation occurs, concrete filling of 18 MPa(T = 100 mm) and 150 mm~237 mm auxiliary concrete layer and 240 mm concrete track(TCL) are applied to the upper part. The concrete is installed in an excessive amount of about 600 mm between the lower part of the rail and the tunnel rock bed. Therefore, in this study, it is necessary to analyze the concrete crack structure according to the depth of the existing tunnel and the modified tunnel section, and to evaluate the adequacy of the required thickness of the tunnel floor concrete for securing the crack stability of the concrete.