• 한국자동차공학회논문집
• /
• 제14권3호
• /
• pp.51-57
• /
• 2006

The contact pressure distribution between a rubber wiper blade and a glass windshield is a major factor for wiping performance. A modeling and simulation method has been developed to forecast the contact pressure distribution on a wiper blade. For modeling multi-body dynamics of an wiper linkage system and flexible nature of wiper blade, ADAMS and ADAMS/flex are employed. A simulation study has been also conducted to obtain contact pressure distribution. Comparison between simulation and measurement is provided to ensure fidelity of the model and the simulation method.

• 한국자동차공학회논문집
• /
• 제18권2호
• /
• pp.83-90
• /
• 2010

The windshield wiper consists of 4 parts: a blade, an arm, a linkage and a motor. The wiper blade makes contact with the windshield and is designed to be operated normally at an angle of 30~50 degrees to the front glass. If the contact pressure between the wiper blade and windshield surface is too high, noise and wear of the rubber will result. On the other hand, if the contact pressure is too low, the performance will do badly, since foreign substances such as dust and stains will not be removed well. The pressure and friction of the wiper blade has a great influence on its effectiveness in cleaning the front window. This is due to the contact of the rubber with the window. This paper presents the dynamic analysis method to estimate the performance of the flat type blade of the wiper system. The blade has a nonlinear characteristic since the rubber is an incompressible hyper-elastic and visco-elastic material. Thus, Structural dynamic analysis using a complex contact model for the blade is performed to find the characteristics of the blade. The flexible multi-body dynamic model is verified by the comparison between test and analysis result. Also, the optimization using the central composite design table is performed.

• 한국자동차공학회논문집
• /
• 제11권6호
• /
• pp.134-140
• /
• 2003

The film sensor is used for measuring pressure distribution at planar area, especially at a small space or gap. The present paper deals with the development of film type sensors and system for pressure distribution measuring. The developed system is consist of (1)film sensor with 40/sup */40 array, (2)PCI interface card with maximum sampling rate of 100㎐, and (3)software for data processing and real-time display. The contact pressure test of wiper blade and front glass of vehicle was performed with wiper blade by 40cm. Generally spring force of wiper arm is designed at 0.7∼1kN. Test results of total force was 9.4N and 7.1N in each driver and passenger toward. The paper suggested possibility for base definition in wiper design. A windshield wiper blade experiment revealed that the system successfully measured the contact force distribution during static state, showing the usefulness of the developed system.

• 한국자동차공학회논문집
• /
• 제18권4호
• /
• pp.79-83
• /
• 2010

Recently, the flat wiper which is one piece wiper and subjected to a pressing force at a single center point is gaining wide applications on automotive windshields. However, nonuniform reactive pressure distributions takes place, so that wiping is not completed at such locations. The wiping performance of the flat wiper is best when a wiper and a curved windshield have perfect contact without gaps under the specified pressing force of 13 ~ 15 gf/cm. Therefore, it is necessary that the realistic curvature equation of a wiper spring-rail should be obtained. Finite element analysis, CATIA script-macro function, and the least square method were utilized to find out the curvature of a spring-rail for a perfect contact with a windshield under a specified concentrated load. The curvature equation became the third order polynomial.

• 한국소음진동공학회논문집
• /
• 제18권4호
• /
• pp.465-472
• /
• 2008

An automotive windshield wiper system is modeled mainly for vibration analysis purpose. The model is composed of solid links, ideal joints, imperfect joints to simulate unavoidable manufacturing defects and bushings having stiffness, contact between a wiper blade and a wind screen glass, friction, a spring and an actuator. Main stream of wiper dynamics analysis has been obtaining a closed form of system of equations using Newton's or Lagrange's formula and doing a numerical simulation study to understand and predict the behavior of it. However, the modeling process is complex since a wiper system is of multibody and a contact problem occurs. When imperfection, such as dead zone of a joint and stiffness of a rubber bushing, should be included, the added complexity makes the modeling difficult. Since the imperfection is understood as main cause of problematic vibration, the dynamics model of a wiper system aiming vibration analysis should include such unavoidable manufacturing defects in the model. An open form of dynamic model of a automotive windshield wiper system with imperfect joints using a commercial software is obtained and a simulation analyssis is conducted for vibration reduction study.

• 한국자동차공학회논문집
• /
• 제23권3호
• /
• pp.292-298
• /
• 2015

A wiper is a safety device removing rain and debris from windshield and ensuring visibility of drivers. If contact pressure distribution between rubber of the blade and the windshield is unbalanced, unwanted noise, vibration, and abrasion of the blade can occur and sometimes fatal accidents could occur. To improve the safety of the wiper, there have been many researches on the contact pressure analysis of the wiper, but the analysis results were not converged or require much computational time due to material nonlinearity of the rubber and contact conditions between the blade rubber and the windshield. In this research, a simple model with 1D beam and 2D shell elements was used for the contact pressure analysis instead of the 3D blade model. The simplified model saved computational time of the analysis and resolved convergence problems. The accuracy of the analysis results was verified by comparing them with experimental results for different rail spring curvatures.

• 한국소음진동공학회논문집
• /
• 제22권10호
• /
• pp.974-984
• /
• 2012

플랫 블레이드 와이퍼의 블레이드의 누름압 분포를 조정하여 역전과정에서 발생되는 진동을 저감하는 방법을 제시하였다. 블레이드와 유리면 사이에 길이방향으로 불균일한 누름압 분포를 도입, 고무스트립에 점진적인 역전을 유도함으로써 역전과정에서 발생하는 충격력을 저감하였다. 블레이드 내의 바디스프링 형상을 이전 연구에서 제시된 방법을 통해 구해진 형태를 적용함으로써 누름압 분포를 조정하였다. 이 방법을 적용하여 전체 길이에 균일한 누름압과 불균일한 누름압을 발생시키는 두 종류의 블레이드를 개발한 다음 누름압을 측정하여 확인하였다. 두 블레이드에서 발생하는 수직방향 및 횡방향 진동을 측정 비교한 결과, 불균일한 누름압을 가진 블레이드가 균일한 누름압의 블레이드에 비해 훨씬 작은 수직방향 진동을 나타냄을 확인하였다.

• 대한기계학회논문집A
• /
• 제34권7호
• /
• pp.837-842
• /
• 2010

차량의 유리면에 설치된 와이퍼 시스템은 비나 눈이 올때 운전자의 시야를 확보해주는 중요한 도구이다. 블레이드는 유리면 위의 물체를 닦아내는 가장 중요한 도구이다. 와이퍼 암의 스프링이 블레이드를 유리면 위에 누를 때, 적절한 누름압이 유지되어야 최적의 성능을 얻을 수 있다. 이번 연구에서는 전체 와이퍼 시스템에 대한 동적 해석이 이루어졌다. 상용 구조 동역학 해석 프로그램인 SAMCEF를 이용하여 와이퍼 시스템의 3차원 유한 요소 모델이 생성되었다. 동적 상태에서 블레이드의 누름압의 분포가 계산되었다. 그리고 시뮬레이션 결과를 실험 결과와 비교를 하였다. 이번 연구의 결과를 이용하여 블레이드의 누름압 분포를 예측해 볼 수 있다.

• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.55-62
• /
• 2013

An analytical procedure to determine a proper profile of the spring rail that generates intended contact pressure distribution in the flat wiper blade is introduced. The flat wiper blade is one piece blade and subjected to pressing force at a center point. In this type of blade, contact pressure distribution in the tip of rubber strip is determined by the pressing force, the initial profile of the blade before contact and bending stiffness of the blade. Experimentally obtained bending stiffness of the blade assembly is almost identical to that of the spring rail. Principle of reciprocity has been used to define the initial profile of spring rail from the deformed profile that is assumed to be identical to the windshield glass profile. The procedure has been verified experimentally by measuring the contact pressure of the blade assembled with the spring rail designed by the procedure proposed here. Measured contact pressure distributions of the blades show good agreements with intended distributions over the entire blade span. Consequently, it can be concluded that proposed procedure has relatively good accuracy in developing the spring rail for flat blade having a specific contact pressure distribution.