• Journal of the korean Society of Automotive Engineers
• /
• v.10 no.3
• /
• pp.51-59
• /
• 1988

The wake structure behind a van type vehicle was studied experimentally with a 5-hole yawhead probe. Through an effective calibration method of the 5-hole yawhead probe, the flow properties such as velocity vector, total pressure and static pressure were obtained on two cross sections within the wake. These results combined with the surface flow visualization performed in the previous study, yielded some information about the wake structure. When the model was placed in a stream with zero yaw angle, two counter rotating vortices were observed behind the model which pull down the surface flow on each side of the model. With increasing the yaw angle, the surface flow on the windward side changed to divide the flow in two directions, one flows upward on the upper part and the other flows downward on the lower part of the windward side. Hence a new weak vortex was created on the upper windward side, which resulted 3 vortices within the wake. The size and the strength of the vortices increased with yaw angle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.135-147
• /
• 2000

Section design of vehicle structure has been developed by two methods. One is the section property method which uses section property as a design variable. This method shows the tendency of an optimum section approximately. The other method is the section shape method which utilizes geometric parameter of section as a design variable. Practical solutions are obtained by this method. However, it is very expensive for large-scale problems due to the large number of geometric parameters. These two methods are compared through several sample problems. The finite element method is used for the structural and sensitivity analyses. The results are analyzed based on the number of function evaluations, the quality of cost function, the complexity of programing, and etc. The applications of both methods are also discussed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.19-26
• /
• 2002

The objective of this study is to examine a DI(Direct Injection) gasoline spray development process under different ambient pressures using PIV(Particle Image Velocimetry). fuel spray experiments were performed within a constant volume chamber. The spray structure, velocity maps, velocity and vorticity contours were obtained to investigate its spray characteristics. It was found that higher ambient pressure has a significant effect on radial growth of the spray. The position which has a maximum velocity moved from the spray edge to the spray center as ambient pressure was increased. Higher ambient pressure moved a maximum vorticity position upward of the spray.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.28-35
• /
• 1997

Occupant injuries are always possible in a rollover accident, one of the major accidents in a bus. Thus the structure of body frame should have sufficient strength to protect passengers under accidental loads,. ECE(Economic Commission for Europe) regulation No.66 prescribes that residual space shall be preserved in the passenger compartment during and after the structure has been subjected to the prescribed rollover test. Rollover test on a bus section was completed according to the regulation. The coordinates of body section before and after rollover were measured, and it was checked that the structure still complied with the requirements of residual space. Direct measurement on a bus is difficult because of its large size. Thus photogrammetry by photographing and 3 dimensional digital modeling was introduced, and the coordinates of each point were measured through this method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.148-154
• /
• 1997

The safety problems of buses have been arisen due to the increasing of road traffic. Occupant injuries are always possible in the rollover accident and the frontal impact. Thus the structure of bus should have sufficient strength to protect passengers under accidental loads. ECE(Economic Commission for Europe) regulation No.66 prescribes that the superstructure of the vehicle shall be sufficient strength for passengers' surviving and the residual space shall be preserved in the passenger compartment during and after the standard rollover accident situation. Rollover test and simulation on a large-sized bus was completed according to the regulation. The coordinates of the points on the bus were measured by photogrammetry system. The rollover situation was revived by structural crashes simulation software, PAM-CRASH, and it was checked that the structure still complied with the requirements of residual space during rollover situation. The residual space was preserved during rollover, so it was proved that the structure of the investigated bus had much probability of survival in rollover accidents.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.6
• /
• pp.78-86
• /
• 1995

The structure of premixed turbulent flames in a constant-volume vessel was investigated using a microprobe method. The flame potential signal having one to eight peaks was detected in the case of turbulent flames, each of them being regarded as a flamelet existing in the flame zone. Based on this consideration, the flame propagation speed, the thickness of the flame zone, the number of flamelets and the separation distance between adjacent flamelets in the flame zone were measured. The experimental resuits of this work suggest the existence of "reactant islands" behind the flame front when the turbulence was intensified to some extent. The critical(lowest) ratio of turbulence intensity to the laminar burning velocity being found to be about 0.7 for the formation of reactant islands in this experiment.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.29-36
• /
• 2014

The accident statistics use the data from police accident reports and statistics. Although the official accident statistics are useful, they provide very limited information about how accidents occur, the cause of the accident and the injury mechanisms. This limitations could be overcome by carrying out the in-depth accident study and analysing investigations, collecting more detailed information. Meanwhile a net of in-depth investigation teams are operating worldwide, such as NASS (National Accident Sampling System) and CIREN (Crash Injury Research and Engineering Network) in US, OTS (On the spot investigation) in UK. In this study, the database structure and variables of Korea in-depth accidents investigation system would be proposed through considering the database structure of GIDAS (Germany In-Depth Accidents Study). GIDAS is one of the best system on the in-depth accident study system in the world. GIDAS was established in 1999 as a cooperation project between Federal Highway Research Institute of Germany (BASt) and research association on automotive engineering of German Car Industry(FAT). The iGLAD (Initiative for the Global Harmonization of Accident Data) was also considered to introduce into the database variables of Korea in-depth accident study. Current police reports were compared with GIDAS and iGLAD. To collaborate of the Worldwide in-depth accident data, this paper proposed that the database of Korea in-depth accident study would be introduced the structure of GIDAS and the core variables of iGLAD. Harmonization of the structures and core variables of Korea in-depth accident study will be better than the making unique ones. The database structure and core variables of KIDAS(Korea In-Depth Accident Study) introduced of GIDAS and iGLAD.

• Journal of the Korea Convergence Society
• /
• v.8 no.4
• /
• pp.189-197
• /
• 2017

In the design of an automotive structural component, one of the more important tasks for a design engineer is to determine the life of the component and to ensure that the component will not fail prematurely. In order to accomplish this, a design engineer will first use simple section analysis to come up with a section shape in the concept design stage and use more advanced analysis for stress level. At this stage, the analysis should focus on understanding overall behavior in terms of load paths and gross stress levels. A model that is adequate for a stiffness analysis of the structure will usually provide an adequate level of stress information in the design process. To perform a detailed stress analysis, the structure models must have the detailed local areas such as stress concentrations or force(or displacement) distributions. This paper is to present the design considerations for the stress analysis of automotive structure.

• Design & Manufacturing
• /
• v.16 no.4
• /
• pp.24-33
• /
• 2022

Fiber-reinforced plastics(FRPs) have excellent specific stiffness and strength, so they are usually used as automotive parts that require high rigidity and lightweight instead of metal. However, it is difficult to predict the mechanical properties of injection molded parts due to the fiber orientation and breakage of FRPs. In this paper, the fiber orientation characteristics and mechanical properties of injection molded specimens were evaluated in order to fabricate automotive transmission side covers with FRPs and design a rib structure for improvement of their rigidity. The test molds were designed and manufactured to confirm the fiber orientation characteristics of each position of the injection molded standard plate-shaped specimens, and the tensile properties of the specimens were evaluated according to the injection molding conditions and directions of specimens. A gusset-rib structure was designed to improve the additional structural rigidity of the target products, and a proper rib structure was selected through the flexural tests of the rib-structured specimens. Based on the evaluation of fiber orientation and mechanical characteristics, the optimization analyses of gate location were performed to minimize the warpage of target products. Also, the deformation analyses against the internal pressure of target product were performed to confirm the rigidity improvement by gusset-rib structure. As a result, it could be confirmed that the deformation was reduced by 27~37% compared to the previous model, when the gusset-rib structure was applied to the joining part of the target products.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.9
• /
• pp.807-815
• /
• 2017

Auxetic structures with negative Poisson's ratio can be used to achieve high mechanical properties in energy absorption and destruction toughness. In this paper, we aim to design an auxetic structure which has a high negative Poisson's ratio and a stiffness over 50N/mm by using an optimization method. Length(L), thickness(t) and angle(${\theta}_1$, ${\theta}_2$) of an auxetic pyramid are the design parameters, and also stress, Poisson's ratio and stiffness are thr reaction factors. We used Box-Behnken method and conducted 4 factors - 3 levels experiment design. Finite element models are analyzed by using Edison program CSD_EPLAST.