Proceedings of the Korean Institute of Information and Commucation Sciences Conference
/
2017.05a
/
pp.275-278
/
2017
The automotive society is facing many challenges in minimizing the energy loss to improve performance and fuel economy of the vehicle. This work "Implement of Power Density for AC Generator Using a Fill Factor of Slot" is a research in Electrical Generator design, to improve power density of Alternator used in conventional IC engine powered vehicles. The power density of the alternator directly influences the fuel economy and performance in the motor vehicle. The size and weight of the alternator can be reduced by suitably designing power density of alternator. The simulation model of alternator is made and tested for different stator space factor using solid and round conductor to demonstrate the improvement in the output performance and efficiency. The result shows that there is an average 10% improvement in efficiency of alternator by using the solid conductor. The energy balance of the system also increased SOC in the base model.
Journal of the Korean Society of Industry Convergence
/
v.26
no.4_2
/
pp.649-656
/
2023
Recently, global warming has become severe, and regulation is established for carbon savings each field. its regulation is applied to various fields using IC engine such as automobile, ship, agricultural machine. Therefore engine block applied Common Rail Direct Injection(CRDI) technology, that carry out thermal-structure analysis to examine design. The thermal load about 900℃ by explosion was applied in cylinder. And pressure about 9 MPa(90 Bar) was applied to structure analysis. As a result, it was the highest at 185.99℃ at the top of cylinder. Static-structure analysis applied thermal load, that was shown maximum equivalent stress at 142.59 Mpa and Maximum principal stress 145.03 MPa, Minimum principal stress -149 MPa. When compare analysis results to material property, it design is safety structurally.
Park, Jungyeol;Song, Inchae;Kim, Boo-Gyoun;Kim, Eun-Ha
Journal of the Institute of Electronics and Information Engineers
/
v.53
no.8
/
pp.76-82
/
2016
In this paper, we evaluated shielding effectiveness (SE) of carbon nanotube (CNT) film using near field scanning (NFS) in near field analysis. We adopted CNT film with deposit carbon density of 5% and thickness of 1mm for evaluation of shielding characteristic. Using a test coupon analogized to an actual IC package, we measured SE according to measuring position and SE according to distances between the CNT film and the test coupon. As a result, the measured SE in the near field varied with frequency. Especially, the measured electric field SE in the center of the test coupon is better than that of the measured edge point of the test coupon where it is affected by fringing effect. The results show that the measured SE in the near field is affected not only by frequency but also by measurement environment such as position and height of the probe and height of shielding film. In conclusion, we should choose proper methods for SE measurement considering interference distance in the electronic control system because there is little correlation between the proposed evaluation method in the near field and ASTM D 4935-10.
Journal of the Institute of Electronics and Information Engineers
/
v.51
no.7
/
pp.230-238
/
2014
In this paper, we propose the possible way of accurate analysis and examination of ITO sensor to discriminate whether mutual capacitance ITO sensor is defective by using mutual capacitance of data in each node which consists of electrodes inside of ITO sensor. We have analyzed the structure characteristic of mutual capacitance ITO sensor which is used as an input device for not only small size electronics like mobile phone and tablets but also big size electronics and designed the circuit to inspect ITO sensor using touch screen panel IC. Set a variable related with mutual capacitance of charge and discharge and Implement to find and analyze accurate position when defect is made through the data from each node of ITO sensor. First, we can set a yield effective range through the first experiment data of mutual capacitance ITO sensor and by using the data of each node of ITO sensor which is the result from the second experiment, we can verify accuracy and effectiveness of effective range from the first experiment as a sample which is used in this experiment.
Journal of the korean Society of Automotive Engineers
/
v.24
no.5
/
pp.98-103
/
2002
이제 카트 정렬과 휠 셋업에 필요한 최적의 변수들을 알아보았다. 실제 세팅은 위에서 언급한 내용 이외에도 많은 것들을 고려하여야 한다. 타이어 접지력의 세팅은 경기장, 날씨, 제품의 불 균일성 등을 고려하여 야 한다. 즉, 어떤 경기장은 코너의 반경이 다른 경기 장 보다 크며 어떤 경기장은 코너가 매우 많기도 하여 세팅을 상황에 맞게 하여야 하는 것이다. 각각의 변수를 세팅할 경우는 중간 값을 취하는 것이 바람직하여 이 중간 값을 취하는 것이 바람직하며 이 중간 값을 각각의 경기장의 특성에 맞추어 변화시키면 되는 것이다. 예를 들면, 접지력이 작게 발생되는 경기장(혹은 매우 추운날씨) 에서는 캐스터를 코기 하여 초기 회전 발생이 용이하게 할 수도 있다. 또한 토우인 값을 크게 하여 타이어가 마찰을 더욱 많이 발생하여 타이어의 온도가 급격히 상승하여 원하는 접지력의 수준에 용이하게 도달할 수 있게 하는 것이다. 그러나 이러한 세팅은 다른 핸들링 문제를 야기할 수 있다는 것을 이해하여야 하며 이러한 문제를 해결하는 또 다른 노력이 필요하게 되는 것이다. 가장 중요한 것은 후륜 내측으로부터는 조종 성능을 향상시키는데 필요한 접지력을 거의 기대하지 못한다는 것이며 마찰이 적게 발생하여 손쉽게 동력 손실을 초래하고 있다는 것이다. 그러므로 회전을 할 경우에도 속도를 낮추어서는 안되며 이렇게 하이야 핸들링이 매우 용이하게 되는 것이다. 그러나 위의 설명에서도 보았듯이 일부 세팅을 변경하면 여러 곳이 그 효과가 나타난다. 예를 들어 후륜의 간격을 변화시키면 카트에서 무게이동 뿐만 아니라 회전 시에 가속이나 감속에 의한 회전 토크의 효과도 달라지게 된다. 특정한 세팅의 변화가 어떻게 작용할 것이라는 확신을 가지고 있다고 할지라도 세팅에서 가장 중요한 것은 주행 기록이다. 여기서 설명되어진 많은 내용이 주행 기록을 향상시키기를 바라는 바이다.간이 육색과 총육색소 함량에는 영향을 미치지 않는 것으로 나타났다. 관능적 특성평가 중 육색과 육즙참출은 대조구와 비교하여 CLA급여 처리구가 유의적인 차이가 없었으나, 근내지방 축적 정도와 전체적인 기호성은 대조구에 비하여 CLA 급여 처리구가 유의적으로 높은 평가를 받았다(p<0.05). 간격은 술 후 1년 후까지도 지속적으로 감소하는 경향을 보였다. 따라서 이 기간동안에는 추적관찰이 필요한 것으로 생각된다.경미하게 나타났으며, 이는 2% 흥국 첨가식이의 섭취로 인한 bromobenzene 대사 및 유해산소 해독의 촉진에 기인되기 때문일 것으로 생각된다.다.과 및 지질과산화억제효과의 순과 일치하였다. 총 flavonoid 함량은 DPPH 라디칼 제거효과에 대한 $IC_{50}$/ 값과 높은 상관관계(r=-0.9924, p<0.01)를 나타내었다.이 우수한 심근보호 효과를 나타내나, 허혈시간이 2시간을 초과하면 심근의 혈역학적 기능과 미세구조의 변화는 중등도의 저온(22∼24$^{\circ}C$)에서 유의하게 악화되었다. 이 같은 결과로 볼 때 심근 허혈시간이 2시간을 초과한다면 심근 온도를 낮추어야 할 것으로 판단된다. 7.2, with 64.0% of office workers having an average level between 6- and 9. The degree of stress was higher for females than males, for unmarried salaried and hot-tempered persons. Those not doing exercise were subject to the highest levels of stress, and those a having sufficient sleep were found to be subject to less stress.
Om Ariara Guhan, C.P.;Arthanareeswaran, G.;Varadarajan, K.N.;Krishnan, S.
Journal of Computational Design and Engineering
/
v.3
no.3
/
pp.198-214
/
2016
Oval substrates are widely used in automobiles to reduce the exhaust emissions in Diesel oxidation Catalyst of CI engine. Because of constraints in space and packaging Oval substrate is preferred rather than round substrate. Obtaining the flow uniformity is very challenging in oval substrate comparing with round substrate. In this present work attempts are made to optimize the inlet cone design to achieve the optimal flow uniformity with the help of CATIA V5 which is 3D design tool and CFX which is 3D CFD tool. Initially length of inlet cone and mass flow rate of exhaust stream are analysed to understand the effects of flow uniformity and pressure drop. Then short straight cones and angled cones are designed. Angled cones have been designed by two methodologies. First methodology is rotating flow inlet plane along the substrate in shorter or longer axis. Second method is shifting the flow inlet plane along the longer axis. Large improvement in flow uniformity is observed when the flow inlet plane is shifted along the direction of longer axis by 10, 20 and 30 mm away from geometrical centre. When the inlet plane is rotated again based on 30 mm shifted geometry, significant improvement at rotation angle of $20^{\circ}$ is observed. The flow uniformity is optimum when second shift is performed based on second rotation. This present work shows that for an oval substrate flow, uniformity index can be optimized when inlet cone is angled by rotation of flow inlet plane along axis of substrate.
Using a hydrogen blended compressed natural gas (HCNG) as a fuel for IC engines has a significant meaning in terms of achieving a reduction of automotive exhaust emissions as well as preparing for an upcoming hydrogen economy by constructing hydrogen infrastructure. In addition, a HCNG engine has higher thermal efficiency than a CNG engine, which is another advantage that makes HCNG fuel considered as a future alternative for natural gas. Therefore, in this study, idling operation of a 11 litre HCNG bus engine was investigated in terms of fuel consumption rate and emissions characteristics. The results show that fuel consumption rate was decreased more than 20% by use of HCNG and all the emissions were significantly reduced in idling condition.
Journal of the Korean Institute of Telematics and Electronics T
/
v.35T
no.1
/
pp.67-74
/
1998
The primary cause of air pollution by vehicles is imperfect combustion of fuel. One of the most usual causes of this imperfect combustion is the misfire in IC engins. The U.S. EPA(Environment Protection Agency) and the CARB(California air Resources Board) have imposed regulations for the detection of misfiring in automotive engines. The OBD-II regulations require that misfire should be monitored by the engine diagnostic system, and that the goal of OBD-II is to alert the driver to the presence of a malfunction of the emission control system. Several solutions to the misfire detection problem have been proposed for the detection of misfires. However, the performance of these methods in the presence of misfire is not altogether clear. This paper presents a precise method and system for internal combustion engine misfire. Present invention based upon measurements of engine roughness as derived from crankshaft angular velocity measurements with special signal processing method. Crankshaft angular velocity signals are processed by WDPT, so that the more reliable misfire detection than the time domain analysis. Experimental work confirms that it is possible to apply the WDFT for the detection of misfires in no-load idle and road testing.
Journal of the Institute of Electronics Engineers of Korea SC
/
v.47
no.4
/
pp.7-14
/
2010
Stable-state behaviors of asynchronous sequential machines represented as finite state machines can be corrected by feedback control schemes. In this paper, we propose a state feedback control scheme for input/state asynchronous machines with uncertain transitions. The considered asynchronous machine is deterministic, but its state transition function is partially known due to model uncertainty or inner logic errors. The control objective is to compensate the behavior of the closed-loop system so that it matches a sub-behavior of a prescribed model despite uncertain transitions. Furthermore, during the execution of corrective action, the controller reflects the exact knowledge of transitions into the next step, i.e., the range of the behavior of the closed-loop system can be enlarged through learning. The design procedure for the proposed controller is described in a case study.
Son, Hyun-Sik;Lee, Min-Ji;Kim, Nam Tae;Song, Han-Jung
Journal of the Korea Academia-Industrial cooperation Society
/
v.16
no.9
/
pp.6247-6253
/
2015
This paper presents the transient-response improved LDO regulator based on parallel error amplifiers. The proposed LDO regulator consists of an error amplifier (E/A1) which has a high gain and narrow bandwidth and a second amplifier (E/A2) which has low gain and wide bandwidth. These amplifiers are in parallel structure. Also, to improve the transient-response properties and slew-rate, some circuit block is added. Using pole-splitting technique, an external capacitor is reduced in a small on-chip size which is suitable for mobile devices. The proposed LDO has been designed and simulated using a Megna/Hynix $0.18{\mu}m$ CMOS parameters. Chip layout size is $500{\mu}m{\times}150{\mu}m$. Simulation results show 2.5 V output voltage and 100 mA load current in an input condition of 2.7 V ~ 3.3 V. Regulation Characteristic presents voltage variation of 26.1 mV and settling time of 510 ns from 100mA to 0 mA. Also, the proposed circuit has been shown voltage variation of 42.8 mV and settling time of 408 ns from 0 mA to 100 mA.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.