• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.1
• /
• pp.139-146
• /
• 2011

In present study, it aims to compare the noise and vibration characteristics between magnesium alloy and steel hood panel. The AZ31 magnesium hood panel was fabricated through warm forming process, and the noise and vibration characteristics between both hood panels was compared through the measurement of engine radiation noise and transmission loss, as well as FRF on modal analysis. The sound insulation performance of magnesium alloy was wholly superior to that of steel hood panel, even though the transmission loss of magnesium alloy is lower than that of steel due to mass effect primarily. The FRF characteristics on modal analysis indicates that the resonance frequency of magnesium hood panel is remarkably increased to higher value than that of steel hood panel. The radiation and interior noise of magnesium panel even without acoustic hood insulation were remarkably lower than those of steel hood panel with acoustic insulation, in particular, at a range below 4,000 rpm.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.106-115
• /
• 2007

In this study, first, child headform model was built up, satisfying requirement in the headform validation test. Also, for decreasing both acceleration peak and deformation, a new hood with dome shaped forming in inner panel was investigated. Next, headform impact, complying with draft of EEVC W/G 17, on the central portion of the newly proposed hood were simulated for a steel hood and three aluminum hoods with different thickness for examining the material and thickness effect on HIC value and inner panel deformation. The analysis results explained that aluminum hoods with dome shaped forming in inner panel were highly promising not only for meeting headform safety regulations but also for leading to weight savings. Finally, hood edge design technology in order to reduce pedestrian injury due to the high stiffness of beam type edge and the rigid support, was discussed. Various types of the foam filled edge were designed and their headform safety performance were evaluated. The edge structure with foam filled in upper one third of section exhibited excellent results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.11
• /
• pp.4080-4086
• /
• 2010

In this study, a scanning fixture for flexible parts such as large automotive panels is developed. For the minimization of the weight deflection of a hood outer panel, the N-2-1 fixture principle for flexible parts is adopted in the fixture design. The designed fixture for a hood outer panel is fabricated using the Alufix system. The springback of the entire hood outer panel can be measured successfully by the laser scanning with the developed fixture, which verifies the usefulness of the proposed design method for the flexible panels.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.5
• /
• pp.66-72
• /
• 2014

A kinematic analysis method has been used as analysis method for dynamic behavior of moving parts of vehicle, especially hood part. Such analysis method, however, has its limitations in terms of design technology, including, over travel of hood that occurs due to lack of considerations of compliance characteristics, such as flexible components of hood's weather strip and over slam bumper. Therefore, it is necessary to develop a modeling which reflects compliance of flexible components of hood and elastic characteristics of panel for improvement of design process. In this thesis, a finite element method as mentioned earlier, is developed to represent over travel of hood. Also optimization process applying sequential approximate optimization is suggested to prevent over travel. The over travel analysis method and optimization process, which are developed through the research, would make it possible to design with high quality and credibility. Furthermore, it is expected that the time for design would be reduced and the design quality also improved.

• International Journal of Aerospace System Engineering
• /
• v.3 no.1
• /
• pp.21-24
• /
• 2016

In this study, a optimal design on the hood automotive using eco-friendly natural fiber composites is performed. The hood of an automobile is determined by dividing the Inner panel shape through optimization phase to outer panel and inner panel. It was performed to optimize the size of the thickness of the inner panel and the outer panel by applying a flax/epoxy composite materials. The optimized shape was evaluated for weight-lightening, stability and the pedestrian collision safety. Through the resin flow analysis are confirmed to molding possibility judgment of product.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.08a
• /
• pp.3-10
• /
• 2003

Springback after draw and flange is the critical factor affecting the product quality. It is very difficult to predict the amount of springback not only because of complex geometry and material characteristics of the stamping product, but because the methodology has not been established. In this study, springback mechanism is introduced, and experimental tryout an automobile panel is carried out for die design of automotive hood panel. Further, introduce adapting design and field springback was verified by trial experimental with the measured tryout result. Finally, introduced about general method in order to predict springback in computer simulation.

• Transactions of Materials Processing
• /
• v.20 no.2
• /
• pp.160-166
• /
• 2011

Weight reduction while maintaining functional requirements is one of the major goals in the automotive industry. The use of lightweight magnesium alloys offers great potential for reducing weight because of the low density of these alloys. However, the formability and the surface quality of the final magnesium alloy product for auto-body structures are not acceptable without a careful optimization of the design parameters. In order to overcome some of the main formability limitations in the stamping of magnesium alloys, a new approach, the so-called "hybrid technology", has been recently proposed for body-in-white structural components. Within this approach, necessary level of mechanical joining can be obtained through the use of lightweight material-steel adhesion promoters. This paper presents the development process of an automotive hybrid hood assembly using magnesium alloy sheets. In the first set of material pairs, the selected materials are magnesium alloy AZ31B alloy and steel(SGCEN) as inner and outer panels, respectively. In order to optimize the design of the inner panel, the stamping process was analyzed with the finite element method (FEM). Laser welding by CW Nd:YAG were used to join the magnesium alloy sheets. Based on the simulation results and mechanical test results of the joints, the determination of die design variables and their influence on formability were discussed. Furthermore, a prototype based on the proposed design was manufactured and the static stiffness test was carried out. The results demonstrate the feasibility of the proposed hybrid hood with a weight reduction of 25.7%.

• Transactions of Materials Processing
• /
• v.13 no.2
• /
• pp.115-121
• /
• 2004

Hemming is the last farming process in stamping and determines external quality of automotive outer panels. Few numerical approaches using 3-dimensional finite element model have been applied to a hemming process due to small element size which is needed to express the bending behavior of the sheet around small die comer and comparatively big model size of automotive opening parts, such as side door, back door and trunk lid etc In this study, part model assembling method is suggested and applied to the 3-dimensional finite element simulation of flanging and hemming process far an automotive front hood.

• Transactions of Materials Processing
• /
• v.7 no.6
• /
• pp.603-609
• /
• 1998

An aluminium sandwich sheet is the material fabricated by adhering two aluminum panels to one plastic core. When it has the same bending stiffness as an steel panel it is 65% lighter than steel panel and 30% lighter than aluminum panel. Therefore it is notified exclusively as good substitutive materials for steel body to improve fuel efficiency. An aluminium sandwich sheet, however, has a problem of the lower formability than steel in automotive application. In this paper we intend to develop application technologies of an aluminum sandwich sheet for auto body panels from selecting composed materials of aluminium sandwich sheets to fabricating prototype. We selected aluminium sandwich panels fabricated by Hoogovens company. Through formability tests we have designed the hood part on auto body panels and fabricated a mould and a prototype.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.37-44
• /
• 2004

Automotive company has been endeavoring to develop high strength steels to get higher fuel efficiency of car since the oil shortage in 1970s and to cope with the recent strict environmental regulation. Outer panels(Hood, Roof, Door and Fender) for automobile require higher dent resistance. Bake-hardenable(BH) steels are known as useful for their high deep drawability and high dent resistance. Recently BH steels are increasingly adapted for outer panel use due to their high drawability and high dent resistance. In this study effect of temper rolling on formability (textures, r value) and bake hardenability is investigated fur improving characteristic of bake-hardenable steels.