• 정보보호학회논문지
• /
• 제28권5호
• /
• pp.1119-1127
• /
• 2018

대부분의 침해공격은 악성코드를 통해 발생하고 있으며, 침해공격으로 인한 피해는 사물인터넷/사이버 물리 시스템과 연결되면서 사이버공간에만 국한되지 않고 실생활에 큰 위협이 되고 있다. 이에 따라, 다양한 악성코드 동적분석, 정적분석기술들이 연구되었는데, 악성코드 동적분석들은 결과적인 악성행위를 쉽게 확인할 수 있어 널리 사용되었으나 VM 환경탐지 시 동작하지 않는 anti-VM 악성코드가 증가하면서 어려움을 겪고 있고, 악성코드 정적분석기술들은 코드자체를 해석할 수 있어 많은 정보를 얻을 수 있으나 난독화, 패킹 기술들이 적용되어 분석가를 어렵게 하고 있다. 본 논문에서는 정적분석기술의 주요 장애물인 난독화 유형을 자동식별, 분류하는 기술을 제안한다. 특히, 제안하는 모델을 통해 알려진 패커나 알려지지 않은 패커와 상관없이 일정한 기준에 의해 모든 악성코드를 분류할 수 있는 것이 가능하다. 악성코드 분류는 다양한 활용이 가능하지만, 예를 들면 악성코드 정적 feature에 기반하여 머신러닝 기반 분석을 할 때, 전체 파일에 대해 학습 및 분석하는 방식보다 악성코드 유형별 학습 및 분석이 더욱 효과적일 것이다. 이를 위해, PE구조에서 활용 가능한 feature에 대해 지도 학습 및 비지도 학습 방식의 모델을 설계했고, 98,000여개 샘플을 통해 결과 검증을 진행하였다.

• 한국포장학회지
• /
• 제26권2호
• /
• pp.61-69
• /
• 2020

As post-harvest processes of onions are carried by a 20 kg-net package which results in high-cost and low-efficiency, especially, the insufficient drying and physical damage of onions after harvesting leads to a huge second loss in storage, we had developed a low-cost, high-efficiency post-harvest bulk handling machinery system by collecting onions on a farm using ton-bags, drying with forced air circulation, and sorting/packaging. The post-harvest bulk handling machinery system consisted of 6 devices, and this study designed an automatic feed hopper with a feeding rate control device, an inclined belt conveyor with a two-step chute, and an automatic pallet unloading device for feeding onions into the sorting/packing line. This study also analyzed the performance and control of the total system. The device had 1-ton handling capacity, but the operational condition was set to increase the capacity. The three-step filling method of pallet by the velocity control of the inclined belt conveyor was applied in the post-harvest bulk handling machinery system for the prevention of physical damage. If one worker was set to operate the total system, the time required to complete one palletized load was approximately 5 minutes and 5 seconds. The calculated daily handling capacity was approximately 94 tons, when the daily actual working time was 8 hours. When the developed system was applied to the managerial size of 2,000 ton, the processing cost per ton of the system was decreased by 19.5%, compared with the existing 20 kg-net package-based handling. The developed post-harvest bulk handling machinery system would be a good substitute for the rapid decline and aging of rural labor.

• 생물환경조절학회지
• /
• 제8권4호
• /
• pp.250-256
• /
• 1999

본 연구는 랩을 이용하여 장방형 과채류의 자동포장기를 개발하기 위하여 수행되였다. 과채류의 포장은 과채류의 수분유출을 방지하고, 공기공급을 가능하게 하여 과채류의 신선도를 유지 할 수 있을 뿐만 아니라, 과채류를 직접 포장함으로써 운반도중 조기 부패하거나, 표피의 손상을 억제할 수 있다. 또한 포장에 의한 농촌의 일손 부족문제를 해결하고 소포장 단위의 신선한 과채류를 원하는 소비자의 구매욕구를 충족시킬 수 있도록 있는 자동포장기를 개발하였다. 랩을 이용한 장방형과 채류를 1개 이상 자동으로 포장할 수 있는 시스템을 개발하였다. 가지의 포장율은 상품, 중품 모두 포장율이 100%로 매우 우수하게 나타났는데, 이는 포장을 위한 회전단면적이 비교적 균일하고 또한 가지 표면의 물리적 특성 때문으로 판단된다. 오이의 포장율은 매우 우수하였으나, 중품은 상품에 비하여 떨어지는 것으로 조사되었는데, 이는 굽은 정도가 포장율에 영향을 미치기 때문으로 생각된다. 애호박의 포장율은 개수가 증가할수록 떨어지는 것으로 나타났는데, 이는 단면적이 컸기 때문으로 판단된다. 장방형 과채류의 포장개수별 포장효율은 회전단면적의 차이에 따라 효율이 변하는 것을 알 수 있었다.

• 한국산학기술학회논문지
• /
• 제13권10호
• /
• pp.4392-4397
• /
• 2012

본 연구에서는 우레탄레진(TSR-755)을 이용하여 레이저 조형으로 시작형 몰드를 가공하고, 상용패키지(Unigraphics)를 이용하여 자동차 단자함 케이블 케이스를 설계한 후 사출성형해석(Simpoe-Mold)을 사용하여 충전, 보압, 냉각, 변형해석을 수행하여 게이트 위치 선정 및 냉각 사이클 등을 검토 하였다. 해석결과, 세라믹소재 가공 후 사출금형에 인서트시켜 성형 시 열전도도 및 냉각시간을 줄여 줌을 확인할 수 있으며, 게이트 및 냉각라인 선정을 빠른 시간에 결정할 수 있어 생산성 향상을 가져올 것으로 나타났다.

• 한국의학물리학회:학술대회논문집
• /
• 한국의학물리학회 2005년도 제30회 춘계학술대회
• /
• pp.47-50
• /
• 2005

The aim of radiosurgery cures a patient to deliver the lower dose at the normal organ and the higher dose at the tumor. Therefore accuracy of the dose is required to gain effect of radiosurgery in surgical planning. In this paper, we developed the methods of target approximation for a fast treatment planning. Nominally, the stereotactic radiosurgery(SRS) using Linac and Gamma knife produces spherical dose distribution through circular collimators using multiple arcs and 201 holes on semi-spherical helmet by $^{60}Co$. We developed an automatic radiosurgical plan about spherical packing arrangement. To automatically plan the SRS, new planning methods based on cylinder and cube structure for target shaping was developed. This approach using heuristic and stochastic algorithm is a useful radiosurgical plan without restrictions in the various tumor shapes and the different modalities.

• International Journal of Advanced Culture Technology
• /
• 제9권4호
• /
• pp.288-294
• /
• 2021

There are various ways to be infected with malicious code due to the increase in Internet use, such as the web, affiliate programs, P2P, illegal software, DNS alteration of routers, word processor vulnerabilities, spam mail, and storage media. In addition, malicious codes are produced more easily than before through automatic generation programs due to evasion technology according to the advancement of production technology. In the past, the propagation speed of malicious code was slow, the infection route was limited, and the propagation technology had a simple structure, so there was enough time to study countermeasures. However, current malicious codes have become very intelligent by absorbing technologies such as concealment technology and self-transformation, causing problems such as distributed denial of service attacks (DDoS), spam sending and personal information theft. The existing malware detection technique, which is a signature detection technique, cannot respond when it encounters a malicious code whose attack pattern has been changed or a new type of malicious code. In addition, it is difficult to perform static analysis on malicious code to which code obfuscation, encryption, and packing techniques are applied to make malicious code analysis difficult. Therefore, in this paper, a method to detect malicious code through dynamic analysis and static analysis using Trojan-type Downloader/Dropper malicious code was showed, and suggested to malicious code detection and countermeasures.

• 근관절건강학회지
• /
• 제30권3호
• /
• pp.263-272
• /
• 2023

Purpose: The aim of this study was to provide a scientific basis for shelf life and re-establish the shelf life in a hospital environment by investigating the validity periods of various packaging materials. Methods: We selected six departments to store sterilized items, prepared 482 sterilized items, and stored them for 12 months. Each sample was tested using a microbiological culture in the laboratory every two weeks. When the result was positive, the sample was considered contaminated. The temperature and relative humidity were measured using an automatic control system to investigate the storage environment during the study period. Results: Except for two samples, which were positive in the 22nd and 28th weeks, 480 samples were negative. The temperature and relative humidity of the sample storage area were measured every week. The annual average temperature was 23.6±1.6℃, and the mean relative humidity was 35.1±15.2%. The cabinets used in this study were the two-open and four-closed types. Conclusion: This study confirmed the validity of the expiration date in a hospital environment. Based on the results, the nonwoven fabric remained sterile for more than nine months. No case of contamination of the paper-plastic pouch packaging was observed, owing to the microbial culture for two months.

• 한국화재소방학회논문지
• /
• 제30권2호
• /
• pp.98-105
• /
• 2016

물류창고 화재위험성은 보관물품, 포장재 및 파렛 등의 가연성과 화재하중 그리고 창고 내부 천장높이, 랙크 등의 저장높이와 배치, 통로 폭 등에 따라 결정된다. 물류창고의 소화 또는 진압대책은 이러한 주요 인자를 고려한 가연물 등급 분류기준을 마련하고 스프링클러설비 설계기준을 적용해야 한다. 본 연구는 국내 물류창고의 자동식스프링클러 적용을 위한 첫 단계로서 경기도 소재 5개 물류단지 내 28개 창고 동을 대상으로 수용물품의 분포 및 창고 공간특성을 현장 조사하였다. 아울러 미국 유럽 및 일본의 물품 분류기준을 분석하였으며 이를 통하여 물류창고 수용물품의 등급분류기준 마련을 위한 기초자료를 제시하고자 한다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.904-908
• /
• 2008

As the various industrial production machinery has come into being by development of industrial technology, the productivity of the basic industrial production machinery has improved and the international competitiveness of the one of Korea has strengthened. However, at the same time, noise from various industrial production machinery disturbs the quiet environment. There are 35 kinds of the noise emission machinery defined in the noise and vibration control act according to the horse power and the number of machinery. These were classified in 1992 through investigation from 1990 to 1991, and the characteristic of the noise emission machinery may be different from the past one. So we need to investigate the characteristics of the noise emitted by machinery to control it rightly. Also we need to investigate the new noise emission machinery which has come into being recently. In this survey, we measured sound intensity of 32 noise emission machinery to calculate the sound power levels of those and investigated the characteristic of the sound power level of those according to the frequency. From the survey, we found that the forging machine, concrete pipe and pile making machine, sawing machine, etc. are the noisy machinery. And the automatic packing machine, sewing machine, centrifuge, etc. are the silent machinery. Also the generator, the concrete pipe and pile making machine, the printing machine, etc. emit the low frequency noise, and the molding machine, the stone cutter, the metal cutter, etc. emit the high frequency noise. Lastly, we intented to propose the proper guide line of classifying noise emission machinery.

• 한국기계가공학회지
• /
• 제20권12호
• /
• pp.129-135
• /
• 2021

Injection molding is a manufacturing method of melting the polymer resin and injecting it into a mold to molding it into the desired form. Due to the short molding time and outstanding formability, complex products can be shaped with high precision and it is the most widely used polymer molding method. However, there may be areas that are not filled depending on the location of the injection gate where polymer resin is injected. Formability is determined by deformation and surface precision due to the impact of residual stress after molding. Hence, choosing the location of the injection gate is very important and molding analysis of injection molding is essential to reduce the cost of the mold. This study evaluated the injection formability based on the location of the injection gate of the vertical machining center ATC tool port using injection molding analysis and the results were compared and analyzed. Injection molding analysis was conducted on filling, packing, and deformation according to the location of the gate of the ATC tool port. From each injection gate location, filling time, pressure, and maximum deformation were compared. At gate 2, conditions of molding time and the location of the gate were far superior in production and quality. Gate 2 produced the smallest deformation of 0.779mm with the best quality.