• 대한임베디드공학회논문지
• /
• 제7권1호
• /
• pp.41-52
• /
• 2012

Recently, FlexRay was developed to replace controller area network (CAN) protocol in chassis networking systems, to remedy the shortage of transmission capacity and unsatisfactory real-time transmission delay of conventional CAN. FlexRay network systems require correct synchronization and complex scheduling parameters. However, because platform configuration register (PCR) setting and message scheduling is complex and bothersome task, FlexRay is more difficult to implement in applications than CAN protocol. To assist a network designer for implementing FlexRay cluster, this paper presents an analysis of FlexRay platform configuration register and automatic generation program of PCR. To demonstrate the feasibility of the automatic generation program, we evaluated its performance using experimental testbed.

• 산업공학
• /
• 제12권2호
• /
• pp.305-311
• /
• 1999

Robot task program is needed to control and manage a Robot without explicitly describing the robot program by user which includes commands, procedures, geometric and signal data in the detail level. To use the Robot task program, a computer system is required to convert the Robot task into the Robot program, which can be understood by the Robot. In this paper, the systemic method for automatic generation of explicit Robot programs (ERP) from task-level commands is described. Specifically, a 3-step procedure including Robot task decomposition, task synchronization and ERP generation is presented.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.720-725
• /
• 1991

This paper is concerned with the program of the automatic mesh generation for 2-dimensional domain which contains the curved boundaries and holes. This program treats a new vertical - line drawing method. This method starts with 4-subdivisions of problem domain and the classification of the cross points of grid lines and boundaries. And the new node is generated by the vertical line to the line connecting the two intersections of a boundary and two grid lines in general. The boundaries are piecewise-curves composed of lines, circles, arcs, and free curves. The free curves are generated by B-Spline form. Although there were some bad elements for the complex boundary, it was possible to obtain the acceptable elements for the given boundaries. The results of automatic mesh generation can be verified directly by drawing on the computer monitor in executing the program. And it is possible to add the processes - that is, editing, hard copying, etc - using the script file in Auto-CAD.

• 한국정밀공학회지
• /
• 제11권1호
• /
• pp.157-165
• /
• 1994

A general-purpose program for automatic two-dimensional finite-element modelling with quadrilateral elements was developed in this research. The conventional looping method employed in the program was introduced with emphasis on a new splitting criterion and a splitting scheme developed for improving the method. Some application examples were given, which show versatility and applicability of the developed program.

• 대한조선학회지
• /
• 제15권4호
• /
• pp.20-23
• /
• 1978

This paper describes newly developed part generation program on the basis of ACUTE. New program named as ASEP(Automatic Separation Program) has function to separate a contour defined by ACUTE into several parts and store them in the part file. The separation flow is as follows, (1) Basic Contour Generation using ACUTE (2) Separation Line Definition (3) Separation into several parts (4) Storing parts in the part file with their individual name The merit of ASEP is to reduce the number of input cards and to simplify input statements.

• 전기학회논문지
• /
• 제59권10호
• /
• pp.1823-1831
• /
• 2010

This paper proposes an automatic tracking control algorithm for efficiency improvement of photovoltaic generation. Increasing the power of PV systems should improve the efficiency of solar cells or the power condition system. The normal alignment of the PV module always have to run perpendicular to the sun's rays. The solar tracking system, able to improve the efficiency of the PV system, was initiated by applying that to the PV power plant. The tracking system of conventional PV power plant has been studied with regard to the tracking accuracy of the solar cells. Power generation efficiency were increased by aligning the cells for maximum exposure to the sun's rays. Using a perpendicular position facilitated optimum condition. However, there is a problem about the reliability of tracking systems unable to not track the sun correctly during environmental variations. Therefore, a novel control algorithm needs to improve the generation efficiency of the PV systems and reduce the loss of generation. This control algorithm is the proposed automatic tracking algorithm in this paper. Automatic tracking control is combined the sensor and program method for robust control in environment changing condition. This tracking system includes the insolation, rain sensor and anemometer for climate environment changing. Proposed algorithm in this paper, is compared to performance of conventional tracking control algorithm in variative insolation condition. And prove the validity of proposed algorithm through the experimental data.

• 한국해양공학회지
• /
• 제17권1호
• /
• pp.72-79
• /
• 2003

This paper deals with the development of an interface program for automatic plate forming, which can exchange information between the heating line information generation program and the automatic heating apparatus. In this paper, the performance of the developed interface program has been verified from the view point of numerical position control. By applying the interface program to the operation of the automatic heating apparatus, an experiment of line heating has been conducted for several steel plate models. Based on the experimental results, a simplified relation to estimate angular distortion has keen derived as a natural characteristic of the present automatic heating apparatus. As a result of the present study, the prototype of the automatic plate forming system has been constructed, and its application to the real surface models found in the ship will be presented in the near future.

• 한국생산제조학회지
• /
• 제6권4호
• /
• pp.65-71
• /
• 1997

The automation of mesh generation in BEM is very important in numerical analysis field for the time and efficiency. In order to this problem, program and algorithm to achive the purpose of making input data and automation of mesh generation based in Expert System are developed in this study. This program has the function of rotating and zooming. The stress intensity factor which is a criteria of fracture mechanics is calculated and compared with other results to prove efficiency and availability of the program in result.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2009년 춘계학술대회논문집
• /
• pp.125-129
• /
• 2009

In this paper automatic 3D wing shape modeling program is introduced. The program is developed in Visual Basic based on Net Framework 3.5 environment by using CATIA COM Library, and it is used together with CATIA system to model 3D wings with or without flaps. With this program users can easily construct wing models by specifying geometry parameters which are usually design variables with the aid of easy-to-use GUI environment, and specifying sectional airfoil data is done either by using analytic shape functions such as NACA series airfoils or by providing input files with point data describing the airfoil shape. When all the input parameters are provided, users can either work further with the model in the CATIA system which would be automatically started by the program or save the resultant model in the format of users choice. Unstructured grid generation program is also briefly described which can make grid generation task for a 3D wing easy and efficient one when used together with the wing modeling program by choosing STL format as the model's output format.

• 한국CDE학회논문집
• /
• 제4권2호
• /
• pp.79-86
• /
• 1999

A general approach to automatic generation of triangular meshes on three-dimensional surfaces is presented in this paper. The approach, developed with emphasis on program generality and interface with CAD/CAM systems, is based on the double mapping method and the looping method. The double mapping method is introduced and anew splitting scheme is proposed for the looping method employed for triangular mesh generation on the parametric domain. Several application examples are given.