• Geophysics and Geophysical Exploration
• /
• v.21 no.1
• /
• pp.8-14
• /
• 2018

For the purpose of maintenance and prevention of earth fill dams against damage from natural hazards, automatic monitoring through various measuring instruments and resistivity survey has been carried out. Reservoirs and embankments have the structural vulnerability on the agricultural usages since most of them were built more than thirty years ago. The main aim to use monitoring method is to verify the safety and integrity of the dam. Resistivity survey can detect potential weaknesses, such as defective zones, anomalous seepages or internal erosion processes. Permanent resistivity monitoring systems were installed at a reservoir, which daily measurements have been taken every 6 hour. Using monitoring data for one year, anomalous seepage and structural defects were clarified for dam safety. Annual water level fluctuations are around 10 m. During their operation, reservoir dams are subject to a never-ending hydraulic load from the reservoir, which over the years may cause changes in the properties of the inner parts of the dam construction. Detailed analysis of the monitoring results was performed and showed that resistivities at most locations have been very stable over the full monitoring period excluding the effects of water fluctuation and seasons. To investigate the detectability of weak zone using the DC resistivity monitoring, numerical modeling with a simplified model for the drainage at a reservoir dam was also performed. The results showed that the seepage zone near drainage in a reservoir dam could be detected by resistivity response change.

• Economic and Environmental Geology
• /
• v.24 no.4
• /
• pp.421-434
• /
• 1991

Ground magnetic surveys were conducted at four areas where the Yangsan fault, the most prominent lineament in the Kyeongsang basin, appears to be passed through. For data processing, IGRF correction, upward continuation and reduction-to-the-pole were performed. The automatic inversion by using a matrix computation method, which takes the depth to bottom layer of the horizontal two layer structure as the model parameter, has been attempted to delineate the subsurface structure. Upward continuation of the surface magnetic map to the same level of the aeromagnetic survey (KIER, 1989) resulted in very similiar patterns to those of aeromagnetic data. Subsurface modeling of eight profile data show that the strike and dip of the Yangsan fault in study areas are $N6^{\circ}-15^{\circ}E$, and near vertical to somewhat eastward, repectively, despite of the local lithological contrast of each study area. It seems that the magnetic effect of faulting in the study area 1, which locates in the most northern part of the survey areas, is disturbed by that of igneous intrusion. At study area 2, the possibility of volcanic or igneous intrusion, which is 200-300 meters wide along the fault plane was presented. At study area 3, unlike other study areas, distinct fracture zone of 500-700 meters in width was revealed along the surface fault line. The andesitic rocks of the study area 4 have very high susceptibilities and the fault line on surface of this area was shifted about 500 meter eastward, as compared with the inferred fault line by the previous study.

• Korean Journal of Remote Sensing
• /
• v.35 no.6_1
• /
• pp.973-985
• /
• 2019

In this paper, we propose a method to separate the ground and building areas and generate building models automatically through planarity analysis using UAV (Unmanned Aerial Vehicle) based point cloud. In this study, proposed method includes five steps. In the first step, the planes of the point cloud were extracted by analyzing the planarity of the input point cloud. In the second step, the extracted planes were analyzed to find a plane corresponding to the ground surface. Then, the points corresponding to the plane were removed from the point cloud. In the third step, we generate ortho-projected image from the point cloud ground surface removed. In the fourth step, the outline of each object was extracted from the ortho-projected image. Then, the non-building area was removed using the area, area / length ratio. Finally, the building's outer points were constructed using the building's ground height and the building's height. Then, 3D building models were created. In order to verify the proposed method, we used point clouds made using the UAV images. Through experiments, we confirmed that the 3D models of the building were generated automatically.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.459-463
• /
• 2007

본 연구에서는 기존 유출분석의 입력자료 생성 시 발생되는 사용상의 불편함과 다양한 수질 수문 모형에 적용을 위한 유역특성자료 도출 기반의 미비로 인하여 보다 편리하고 체계적인 유역특성자료 분석 시스템을 개발하고자 하였다. 기존 PRMS를 이용하여 유출분석 시 입력자료 생성을 위해 사용되는 USGS WEASEL 벤치마킹을 통하여 시스템 개발항목을 도출하고, 체계적이고 효율적인 시스템 개발 및 유지관리를 위하여 UML을 이용한 객체지향 시스템 설계를 수행하였다. 또한, 편리한 사용자 인터페이스 제공 및 다양한 수질 수문 모형에 적용하기 위한 GIS 컴포넌트 기반인 ArcGIS ArcObject를 이용한 시스템 개발을 수행하였다. 또한, 시범 연구지역인 용담댐 유역을 대상으로 DEM, 토양도, 토지피복도, 임상도 등을 구축하여 유역특성자료 분석 시스템에 적용하여 PRMS의 입력 매개변수를 추출하였다. 본 연구에서 개발한 시스템에 의하여 추출된 매개 변수의 검토를 위하여 용담댐 유역과 구량천 유역을 대상으로 PRMS를 이용한 장기유출모의를 수행하였다. 강우자료 및 기상자료는 기상청의 장수기상관측소의 시계열 자료를 사용하였으며 모의 결과를 검증할 수 있는 하천유출량 자료는 용담댐 지점과 동향수위관측소 자료를 사용하였다. 장기유출모의 목적에 맞는 PRMS 모형을 구성하고 유역특성자료 분석시스템을 이용하여 추출된 매개변수로서 1966년부터 2001년까지 용담댐 유역에 대하여 모의하여 매개변수를 최적화하였고 최적화된 매개변수를 이용하여 각각의 유역에 대하여 검토하였다. 그 결과 용담댐 유역에 대해서는 0.49에서 0.83까지의 모형효율을 나타내었으며 구량천 유역에 대해서는 0.57에서 0.75까지의 모형효율을 나타내어 모의결과가 실측치에 대하여 높은 적합도를 나타내었다.997년 이후로 지속적으로 감소되고 있다.게 될 것이다. 본 연구에서는 현재 진행중인 승기천 오염하천 정화사업이 종료되는 시점을 기준으로 남동유수지에 대해 승기천과 연계한 유수지의 환경개선 방법을 제안하였다. 준설을 통해 유수지의 근본적인 오염원을 제거하고 남동유수지 유입부에 인공습지와 수처리설비를 설치하여 유수지의 수질을 개선하고 개선된 수질이 3급수로 유지하도록 하였으며, 설치된 인공습지에는 철새도래지를 조성하여 유수지 유입수인 철새가 날아드는 하천인 승기천의 테마와 연계하도록 하였다. 인공습지 주변으로 식생호안을 설치하고 유수지 주변에는 산책로를 설치하여 지역주민들의 친환경 수변공간으로 활용하도록 하였다. 1유수지와 연결된 2유수지는 BTL사업을 통해 주변공단으로부터의 오폐수를 원천적으로 차단하도록 하였으며 2유수지를 매립하여 지하는 강우시 유출수 저류가 가능한 화물차주차장으로 활용하고 지상은 녹지공간으로 조성하여 공단근로자 및 지역주민을 위한 휴식공간으로 활용될 수 있도록 제안하였다. 본 연구는 남동유수지 환경 개선 사업 실행을 위한 정책 연구로 연구결과를 인천시가 적극 수용하기로 결정함에 따라 인천시의 환경 현안 문제인 남동유수지의 수질개선을 통해 시민의 휴식 및 여가선용 공간으로 활용하기 위한 사업의 기초자료로 활용되며 이미 설계검토가 시작되었다. 본 연구결과는 유수지 및 저수지의 환경개선 사업의 선두적인 성공사례로 국내 타 지역의 유사한 사업에 있어 벤치마킹을 할 수 있는 훌륭한 사례가 될 것이다.요 생산이 증가하자 군신의 변별(辨別)과 사치를 이유로 강력하게 규제하여 백자의 확대와 발전에 걸림돌이 되었다. 둘째, 동기(銅器)의 대체품으로 자기를 만들어 충당해야할 강제성 당위성 상실로 인한 자기수요 감소를 초래하였을 것으로 사료된다. 셋째, 경기도 광주에서

• Korean Journal of Construction Engineering and Management
• /
• v.14 no.3
• /
• pp.53-64
• /
• 2013

In building construction project, there are numerous information or data parts across many different software applications and professional specialists. BIM (Building Information Modeling), as a medium for managing information generated during construction project, it is intended to enhance the effectiveness of construction management and reap a lot of advantages such as, automatic quantity takeoff, error-free estimation, 4D(3D+Time), 5D(4D+Cost) simulation. Nevertheless, the overall and practical effectiveness of BIM utilization is difficult to justify at this stage. While helpful, there are some limitation when BIM applied to construction management due to the differences of data processing process between BIM and work in the field, limitations of information generated from BIM object and interoperability problem among BIM application. Therefore, this paper propose a framework integrating BIM with cost-schedule information using IFC. And we construct the system prototype based on the framework and performed case study to examine the framework. The proposed framework provides the information basis for BIM based cost-schedule integration. ultimately, the framework increase the utilization of BIM and work efficiency of construction industry by supporting an understanding of information.

• Journal of Veterinary Clinics
• /
• v.33 no.2
• /
• pp.107-112
• /
• 2016

The objective of this study was to determine potential contributing factors associated with biosecurity level of farrow-to-finish pig farms and to develop a classification tree model to explore how these factors related to each other based on prediction model. To this end, the author analyzed data (n = 193) extracted from a cross-sectional study of 344 farrow-to-finish farms which was conducted between March and September 2014 aimed to explore swine disease status at farm level. Standardized questionnaires with information about basic demographical data and management practices were collected in each farm by on-site visit of trained veterinarians. For the classification of the data sets regarding biosecurity level as a dependent variable and predictor variables, Chi-squared Automatic Interaction Detection (CHAID) algorithm was applied for modeling classification tree. The statistics of misclassification risk was used to evaluate the fitness of the model in terms of prediction results. Categorical multivariate input data (40 variables) was used to construct a classification tree, and the target variable was biosecurity level dichotomized into low versus high. In general, the level of biosecurity was lower in the majority of farms studied, mainly due to the limited implementation of on-farm basic biosecurity measures aimed at controlling the potential introduction and transmission of swine diseases. The CHAID model illustrated the relative importance of significant predictors in explaining the level of biosecurity; maintenance of medical records of treatment and vaccination, use of dedicated clothing to enter the farm, installing fence surrounding the farm perimeter, and periodic monitoring of the herd using written biosecurity plan in place. The misclassification risk estimate of the prediction model was 0.145 with the standard error of 0.025, indicating that 85.5% of the cases could be classified correctly by using the decision rule based on the current tree. Although CHAID approach could provide detailed information and insight about interactions among factors associated with biosecurity level, further evaluation of potential bias intervened in the course of data collection should be included in future studies. In addition, there is still need to validate findings through the external dataset with larger sample size to improve the external validity of the current model.

• Journal of KIISE:Computing Practices and Letters
• /
• v.5 no.6
• /
• pp.727-737
• /
• 1999

프로세스 중심 소프트웨어 개발 환경(PSEE : Process-centered Software Engineering Environment)은 소프트웨어 개발자를 위한 여러가지 정보의 제공과 타스크의 수행, 소프트웨어 개발 도구의 수행 및 제어, 필수적인 규칙이나 업무의 수행등과 같은 다양한 행위를 제공하는 프로세스 모형의 수행을 통하여 소프트웨어 개발 행위를 지원한다. SEED(Software Engineering Environment for Development)는 효율적인 소프트웨어 개발과 프로세스 모형의 수행을 제어하기 위해 ETRI에서 개발된 PSEE이다.본 논문에서는 SEED에서 프로세스 모형을 설계하기 위해 사용되는 SimFlex 프로세스 프로그래밍 언어와, 수행지원시스템인 SEED Engine의 구현에 대하여 기술한다. SimFlex는 간단한 언어 구조를 가진 프로세스 프로그래밍 언어이며, 적절한 적합화를 통하여 다른 PSEE에서 사용될 수 있다. SimFlex 컴파일러는 SimFlex에 의해 기술된 프로세스 모형을 분석하고, 모형의 오류를 검사하며, SEED Engine에 의해 참조되는 중간 프로세스 모형을 생성한다. 중간 프로세스 모형을 사용하여 SEED Engine은 외부 모니터링 도구와 연관하여 사용자를 위한 유용한 정보뿐만 아니라 SimFlex에 의해 기술된 프로세스 모형의 자동적인 수행을 제공한다. SimFlex 언어와 수행지원 시스템의 지원을 통하여 소프트웨어 프로세스를 모형화하는데 드는 비용과 시간을 줄일 수 있으며, 편리하게 프로젝트를 관리하여 양질의 소프트웨어 생산물을 도출할 수 있다. Abstract Process-centered Software Engineering Environments(PSEEs) support software development activities through the enaction of process models, providing a variety of activities such as supply of various information for software developers, automation of routine tasks, invocation and control of software development tools, and enforcement of mandatory rules and practices. The SEED(Software Engineering Environment for Development) system is a PSEE which was developed for effective software process development and controlling the enactment of process models by ETRI.In this paper, we describe the implementation of the SimFlex process programming language used to design process models in SEED, and its runtime support system called by SEED Engine. SimFlex is a software process programming language to describe process models with simple language constructs, and it could be embedded into other PSEEs through appropriate customization. The SimFlex compiler analyzes process models described by SimFlex, check errors in the models, and produce intermediate process models referenced by the SEED Engine. Using the intermediate process models, the SEED Engine provides automatic enactment of the process models described by SimFlex as well as useful information for agents linked to the external monitoring tool. With the help of the SimFlex language and its runtime support system, we can reduce cost and time in modeling software processes and perform convenient project management, producing well-qualified software products.

• Korean Journal of Remote Sensing
• /
• v.14 no.4
• /
• pp.376-391
• /
• 1998

Images from satellites will have 1 to 3 meter ground resolution and will be very useful for analyzing current status of earth surface. An image processing system named GeoWatch with more intelligent image processing algorithms has been designed and implemented to support the detailed analysis of the land surface using high-resolution satellite imagery. The GeoWatch is a valuable tool for satellite image processing such as digitizing, geometric correction using ground control points, interactive enhancement, various transforms, arithmetic operations, calculating vegetation indices. It can be used for investigating various facts such as the change detection, land cover classification, capacity estimation of the industrial complex, urban information extraction, etc. using more intelligent analysis method with a variety of visual techniques. The strong points of this system are flexible algorithm-save-method for efficient handling of large size images (e.g. full scenes), automatic menu generation and powerful visual programming environment. Most of the existing image processing systems use general graphic user interfaces. In this paper we adopted visual program language for remotely sensed image processing for its powerful programmability and ease of use. This system is an integrated raster/vector analysis system and equipped with many useful functions such as vector overlay, flight simulation, 3D display, and object modeling techniques, etc. In addition to the modules for image and digital signal processing, the system provides many other utilities such as a toolbox and an interactive image editor. This paper also presents several cases of image analysis methods with AI (Artificial Intelligent) technique and design concept for visual programming environment.

• Journal of the Korea Society of Computer and Information
• /
• v.13 no.5
• /
• pp.53-67
• /
• 2008

At present, for reuse of similar domains between feature model and class model. researches of transformation at the model level and of transformation using ontology between two models are being made. but consistent transformation through metamodel is not made. And the factors of modeling transformation targets are not sufficient, and especially, automatic transformation algorithm and supporting tools are not provided so reuse of domains between models is not activated. This paper proposes a method of transformation from feature model to class model using ontology on the metamodel. For this, it re-establishes the metamodel of feature model, class model, and ontology, and it defines the properties of modelling factors for each metamodel. Based on the properties, it defines the profiles of transformation rules between feature mndel and ontology, and between ontology and class model, using set theory and propositional calculus. For automation of the transformation, it creates transformation algorithm and supporting tools. Using the proposed transformation rules and tools, real application is made through Electronic Approval System. Through this, it is possible to transform from the existing constructed feature model to the class model and to use it again for a different development method. Especially, it is Possible to remove ambiguity of semantic transformation using ontology, and automation of transformation maintains consistence between models.

• Journal of the Korean Society of Radiology
• /
• v.15 no.5
• /
• pp.585-590
• /
• 2021

Wrist braces are being used for patients with wrist trauma. Recently, many studies have been conducted to manufacture custom wrist braces using 3D printing technology. Such 3D printing customized orthosis has the advantage of reflecting various factors such as reflecting different shapes for each individual and securing breathability. In this paper, the stress on the orthosis by the number and position of Velcro bands that should be considered when manufacturing a 3D printing custom wrist brace was analyzed. For customized orthosis, 3D modeling of the bone and skin regions was performed using an automatic design software (Reconeasy 3D, Seeann Solution) based on CT images. Based on the 3D skin area, a wrist orthosis design was applied to suit each treatment purpose. And, for the elasticity of the brace, a wrist brace was manufactured with an FDM-type 3D printer using TPU material. To evaluate the effectiveness according to the number and position of the Velcro band of the custom 3D printed wrist brace, the stress distribution of the brace was analyzed by the finite element method (FEM). Through the finite element analysis of the wrist orthosis performed in this study, the stress distribution of the orthosis was confirmed, and the number and position of the orthosis production and Velcro bands could be confirmed. These experimental results will help provide quality treatment to patients.