• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.586-589
• /
• 2003

Repeater is developed. Based on the systems The up-converter of the WCDMA Digital Optic pecifications, the structure of the up-converter is accomplished and its block diagram is drawn. The up-converter is implemented according to these block diagrams. Subsequently the low pass filter, the automatic level controlled attenuator, the frequency synthesizer and other components for the up-converter are designed and implemented, and a main board to integrate these modules is also manufactured. To reduce the noise floor of system and suppress the RF spurious noise, a PCB layout is performed carefully. For each module consisting of the up-converter and the entire system, the performance tests are accomplished to check the performance about the specifications.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1996.04a
• /
• pp.381-385
• /
• 1996

본 연구에서는 자동화 제조 시스템 (Automatic Manufacturing System :AMS)의 설계및 구현에 있어서 물리적인 검증 (Physical Validation)을 위한 소프트웨어 시스템의 구조를 제안하고 구현하였다. 제안된 소프트웨어 시스템은 설비들과 물류 흐름에 있어서 간섭 검증과 운영 가능성을 검증하는 기능을 제공하며 크게 4개의 모듈로 나누어져 있다. : 1) 기본 형상들을 이용하여 원하는 형상을 정의하는 "Shape Modeling Module", 2) 실제 설비의 Kinematics와 기능을 모델링하는 "Facility Modeling Module", 3) AMS의 물리적인 배치를 구성하는 "Layout Design Module", 4) 모델링된 AMS를 실행시켜 볼 수 있는 "Factory Emulation Module". 이와 같은 소프트웨어 시스템을 구현하기 위해 수행된 주된 연구는 다음과 같다. : 1) AMS를 구성하는 설비들을 모델링하는 방법을 제시, 2) 표준 설비들의 Instancing Parameter 제시, 3) C++과 GL을 이용하여 소프트웨어로의 구현, 4) Flexible Manufacturing System (FMS)에의 응용.lexible Manufacturing System (FMS)에의 응용.

• Proceedings of the IEEK Conference
• /
• 2000.07a
• /
• pp.375-378
• /
• 2000

This paper discusses on application of meta-heuristic algorithms such as the genetic algorithm (GA) and the simulated annealing (SA) to the LSI module placement. We propose useful crossover method for improving of searching capability in genetic algorithm. By using our proposed crossover method, we have been able to keep good schemata in the chromosome and the variety of the solution. From the experimental results, we have obtained better result than the simulated annealing method by starting from the initial placement of the min-cut method.

• Korean Journal of Computational Design and Engineering
• /
• v.16 no.4
• /
• pp.260-267
• /
• 2011

Nowadays, automobile manufacturers are faced with increasing global competition which is required low cost as well as high quality. To reduce shipping and handling cost and delivery time, lots of automobile manufactures tried to build their new factory in the neighborhood of market. Simultaneously, many factories are under construction in developing countries to make efficient use of low-wage workers. However, because systems are installed in developing countries as the same type of domestic facilities, systems have lots of problems such as high installation cost and inefficient use of manpower. To find core problems and generate optimal solution of these problems, thinking process of TOC(Theory Of Constrains) is used. In case of transmission gear machining system, semi-auto system is proposed as the best solution to increase manpower efficiency and system utilization. Semi-auto system consists of automatic machining process and manual transporting process. The system layout is generated based on semi-auto process concept. And, 3D simulation method using QUEST is used to verify production volume of generated system.

• Structural Engineering and Mechanics
• /
• v.12 no.6
• /
• pp.685-698
• /
• 2001

In this paper, a general method for the automatic search for Strut-and-Tie (S&T) models representative of possible resistant mechanisms in reinforced concrete elements is proposed. The representativeness criterion here adopted is inspired to the principle of minimum strain energy and requires the consistency of the model with a reference stress field. In particular, a highly indeterminate pin-jointed framework of a given layout is generated within the assigned geometry of the concrete element and an optimum truss is found by the minimisation of a suitable objective function. Such a function allows us to search the optimum truss according to a reference stress field deduced through a F.E.A. and assumed as representative of the given continuum. The theoretical principles and the mathematical formulation of the method are firstly explained; the search for a S&T model suitable for the design of a deep beam shows the method capability in handling the reference stress path. Finally, since the analysis may consider the structure as linear-elastic or cracked and non-linear in both the component materials, it is shown how the proposed procedure allows us to verify the possibilities of activation of the design model, oriented to the serviceability condition and deduced in the linear elastic field, by following the evolution of the resistant mechanisms in the cracked non-linear field up to the structural failure.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.5
• /
• pp.48-55
• /
• 1999

This paper describes automatic gain control circuit (AGC) design techniques for CMOS CCD camera interface systems. The required gain of the AGC in the proposed system is controlled directly by digital bits without conventional extra D/A converters and the signal settling behavior is almost independent of AGC gain variation at video speeds. A capacitor-segment combination technique to obtain large capacitance values considerably improves the effective bandwidth of the AGC based on switched-capacitor techniques. A proposed layout scheme for capacitor implementation shows AGC matching accuracy better than 0.1 %. The outputs from the AGC are transferred to a 10b A/D converter integrated on the same chip. The proposed AGC is implemented as a sub-block of a CCD camera interface system using a 0.5 um n-well CMOS process. The prototype shows the 32-dB AGC dynamic range in 1/8-dB steps with 173 mW at 3 V and 25 MHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.10
• /
• pp.712-720
• /
• 2001

Algorithms from the research of the layout migration were proposed in the paper. These are automatic recognition algorithm for the VLSI devices from it, graph based construction algorithm to maintain the constraints, dependencies, and design rule between the devices, and high speed compaction algorithm to reduce size of the VLSI area and reuse the design with compacted size for the new technology. Also, this paper describes that why proposed algorithms are essential for the era of the SoC (System on a Chip), design reuse, and IP DB, which are the big concerns in these days. In addition to introduce our algorithms, the benchmark showed that our performance is superior by 27 times faster than that of the commercial one, and has better efficiency by 3 times in disk usage.

• Journal of Digital Convergence
• /
• v.19 no.11
• /
• pp.17-22
• /
• 2021

In this paper, a machine learning-based automatic infographic recommendation system is proposed to improve the existing infographic production method. This system consists of a part that machine learning multiple infographic images and a part that automatically recommends infographics with artificial intelligence only by inputting basic data from the user. The recommended infographics are provided in the form of a library, and additional data can be input by drag & drop method. In addition, the infographic image is designed to be dynamically adjusted according to the size of the input data. As a result of analyzing the machine learning-based automatic infographic recommendation process, the matching success rate for layout and keyword was very high, and the matching success rate for type was rather low. In the future, a study to improve the matching success rate for the image type for each part of the infographic will be needed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.9
• /
• pp.974-978
• /
• 2003

The down-converter of the WCDMA Digital Optic Repeater is developed. Based on the system specifications, the structure of the down-converter is accomplished and its block diagram is drawn. The down-converter is implemented according to these block diagrams. Subsequently a low pass filter, an automatic level controlled attenuator, a frequency synthesizer and other components for the down-converter are designed and implemented, and a main board to integrate these modules is also manufactured. To reduce the noise floor of system and suppress the RF spurious noise, a PCB layout is performed carefully. For each module consisting of the down-converter and the entire system, the performance tests are accomplished to check the performance about the specifications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.6
• /
• pp.900-909
• /
• 1999

The receiving part of the RF system for the digital TRS base stations is developed in this paper. Based on the system specifications, the structure of the RF system is accomplished and its block diagram is drawn. The RF system is implemented according to these block diagrams. Subsequently the RF band-pass filter, the low noise amplifier, the automatic level controlled attenuator, the frequency synthesizer and other components for the system are designed and implemented, and a main board to integrate these modules is also manufactured. To lower the noise floor of the system and suppress the RF spurious noise, a PCB layout is performed carefully. For each module consisting of the RF system and the entire system, the performance tests are accomplished to check the specifications.