• Journal of Korean Society on Water Environment
• /
• v.23 no.2
• /
• pp.228-235
• /
• 2007

For efficient turbid water withdrawal in the Imha reservoir, a selective withdrawal facility was recently installed and operated during summer season of year 2006. In this research, CE-QUAL-W2 model was utilized to assess the efficiency of the selective withdrawal facility, in comparison with the original surface withdrawal, on turbid water management. Model calibration was carried out using data observed at four automatic monitoring stations in the reservoir. It was found that the model appropriately simulated, with the RMSE less than 5.2 NTU, the observed vertical and horizontal distributions of water temperature and turbidity as well as the location of maximum turbid water at each monitoring station. The analysis results showed that selective withdrawal is more effective in removing high turbid water than surface withdrawal as selective withdrawal contributed to reducing $35Mm^3$ of high turbidity water (> 100 NTU) in the reservoir by increasing outflows of high turbid water. Therefore, effective management of turbid water in the reservoir can be achieved by changing locations of intake depending on turbid water distribution conditions. The results of this study will provide some basic information for establishing better operation strategies to cope with turbid water problems.

• Korean Journal of Clinical Laboratory Science
• /
• v.43 no.1
• /
• pp.1-5
• /
• 2011

The infection rate of syphilis is still increasing in the world especially in developing countries and the infection is often seen in large amounts of clinical specimens. For the diagnosis of this disease, Rapid Plasma Reagin (RPR)/Venereal Disease Research Laboratory (VDRL) has still been used as one of major primary methods to diagnose syphilis even though the test readings are somewhat subjective with high false positive rates. Recently, the automatic ARCHITECT Syphilis TP, which is based on the detection of the TP-specific antibodies, has been introduced in many laboratories. Therefore, the clinical assessment of the method is needed to provide primary diagnosis of syphilis at the moment. We evaluated 3 different manual rapid kits and ARCHITECT Syphilis TP comparing with RPR/FTA-ABS and analysed their diagnostic properties. From February 2006 to April 2008, 203 positive and 250 negative specimens, obtained from Chungbuk National University Hospital were used for the evaluation. In the evaluation between manual rapid kits, their specificities were as high as 99.2 ~ 99.6% while their sensitivities were observed with little differences; 98.0% (199/203) for Kit A, 96.6% (196/203) for Kit B, and 97.4% (197/203) for Kit S. In the case of ARCHITECT Syphilis TP test, it showed 100% specificity (250/250) and 98.5% sensitivity (249/250). Kappa values comparing with RPR/FTA-ABS were 0.978 for Kit A, 0.964 for Kit B and Kit S, and 0.987 for ARCHITECT Syphilis TP. From our evaluation, we found out that manual rapid tests and ARCHITECT Syphilis TP have very good clinical accuracies and high kappa agreements with RPR/FTA-ABS. Due to its automation and quick simultaneous diagnosis with another serological markers, we suggest that the ARCHITECT Syphilis TP is one of best suitable method for the primary diagnosis of syphilis and that it might be able to replace RPR method in the laboratories.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.5-5
• /
• 2015

현재 우리나라에서 지상관측장비인 AWS(Automatic Weather System)와 ASOS(Automated Synoptic Observing System)기구가 한반도내 668개 지점에서 운영되고 있다. 이러한 장비는 지상관측장비로 하나의 지점에서 측정된 기상변량들이 특정 영역의 대푯값으로 사용되어지고 있다. 기존의 다양한 지점 단위의 수문 모형에서는 지상관측소를 통한 관측값을 적용하기에 어려움 없이 적절한 결과를 도출할 수 있었다. 컴퓨터의 발달로 인하여 복잡한 물리적 현상을 공간적으로 분석할 수 있는 모형의 구동이 가능해짐에 따라서 수문 분야에서도 다양한 분포형 해석 모형이 활발하게 개발 및 적용되고 있다. 지점 관측 자료는 공간적인 연속성을 반영하지 못하는 한계로 인하여 지점 관측자료를 이용한 공간자료의 생성 기법들이 사용되어지고 있지만 자연계에서 나타나는 정확한 공간적 현상을 재현해주지 못하는 문제점이 존재한다. 이러한 지점 관측의 한계를 해결하기 위하여 공간적인 관측이 가능한 레이더와 위성관측과 같은 원격 관측 장비들이 개발되어 공간적으로 연속성을 갖는 기상변량의 취득이 가능하여졌다. TRMM 강우자료는 지구 전체를 0.25도 약 25km 공간해상도를 갖으며 3시간 간격으로 제공되고 있다. 유역단위의 수문모형에 적용하기에 TRMM 강수자료의 공간해상도는 너무 커서 직접적인 적용에 어려움이 있다. 이러한 점에서 TRMM 자료의 상세화 기법을 통하여 수문모형에 적용이 가능한 1km 이하의 고해상도 자료를 생산하는 연구들이 진행되고 있다. 이러한 상세화 방법은 최종적으로 도출하고자 하는 공간해상도를 갖는 대체 변량(지표면 온도, 고도, 식생, 해수면 기압, 상대 습도, 대기온도, 풍향 등)을 이용하여 회귀분석의 형태로 분석이 이루어지고 있다. 그러나 대체 변량을 통해 도출된 상세화된 TRMM 강우는 간접적인 추정으로 인하여 정확한 결과의 도출에는 한계가 있을 것으로 판단된다. 이러한 점에서 본 연구에서는 한반도내 지상 관측값을 공간적 자료로 변환하여 주는데 효과적으로 평가받는 PRISM 모형에 적용하여 기존 SVM 모형을 통한 TRMM 상세화 결과가 갖는 정확성을 평가해 보고 지점 관측자료의 보간 기법의 평가에 TRMM 자료를 활용하는 방안에 대해 평가해 보고자 한다.

• Journal of Korean Institute of Architectural Sustainable Environment and Building Systems
• /
• v.12 no.6
• /
• pp.591-605
• /
• 2018

The information on the planar figure of the building envelope is commonly required in various criteria related to the energy performance of the building. However, since the method of creating varies depending on each criterion, the information displayed in the planar figure of the building envelope differs considerably according to the person making the figure. In this regard, this study sought to derive the commonly required information for the unification of the information included in the planar figure of the building envelope, and thus examine the standardization of the planar figure of the building envelope based on BIM. Towards this end, 1) the required information about the planar figure of the building envelope was derived through the literature review and case analysis results submitted to the energy performance evaluation agencies, and 2) the standardized output technology using IFC was investigated based on the required information. Therefore, it is expected that the findings of this study will help to create a general-purpose planar figure for the building envelope, and this study can serve as the preliminary research for automatically extracting the information on the planar figure of the building envelope.

• Imaging Science in Dentistry
• /
• v.52 no.2
• /
• pp.171-179
• /
• 2022

Purpose: The aim of this study was to assess the accuracy of cone-beam computed tomographic (CBCT) images obtained using different voxel sizes in measuring trabecular bone microstructure in comparison to micro-CT. Materials and Methods: Twelve human skull bones containing posterior-mandibular alveolar bone regions were analyzed. CBCT images were obtained at voxel sizes of 0.075mm(high: HI) and 0.2mm(standard: Std), while microCT imaging used voxel sizes of 0.06 mm (HI) and 0.12 mm (Std). Analyses were performed using CTAn software with the standardized automatic global threshold method. Intraclass correlation coefficients were used to evaluate the consistency and agreement of paired measurements for bone volume (BV), percent bone volume (BV/TV), bone surface (BS), trabecular thickness (TbTh), trabecular separation (TbSp), trabecular number (TbN), trabecular pattern factor(TbPf), and structure model index (SMI). Results: When compared to micro-CT, CBCT images had higher BV, BV/TV, and TbTh values, while micro-CT images had lower BS, TbSp, TbN, TbPf, and SMI values (P<0.05). The BV, BV/BT, TbTh, and TbSp variables were higher with Std voxels, whereas the BS, TbPf, and SMI variables were higher with HI voxels for both imaging methods. For each imaging modality and voxel size evaluated, BV, BS, and TbTh were significantly different(P<0.05). TbN, TbPf, and SMI showed statistically significant differences between imaging methods(P<0.05). The consistency and absolute agreement between micro-CT and CBCT were excellent for all variables. Conclusion: This study demonstrated the potential of high-resolution CBCT imaging for quantitative bone morphometry assessment.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.11
• /
• pp.87-95
• /
• 2022

The geotechnical information constructed in the National Geotechnical Information DB System has been extensively used in design, construction, underground safety management, and disaster assessment. However, it is necessary to refine the geotechnical information because it has nearly 300,000 established cases containing a lot of missing or incorrect information. This research proposes a method for automatic quality control of geotechnical information using a fully connected neural network. Significantly, the anomalies in geotechnical information were detected using a database combining the standard penetration test results and strata information of Seoul. Consequently, the misclassification rate for the verification data is confirmed as 5.4%. Overall, the studied algorithm is expected to detect outliers of geotechnical information effectively.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.5
• /
• pp.67-77
• /
• 2022

An automatic freeway bus-only lane enforcement system was developed and assessed in a real-world environment. Observation of a bus-only lane on the Youngdong freeway, South Korea, revealed that approximately 99% of the vehicles violated the high-occupancy vehicle (HOV) lane regulation. However, the current enforcement by the police not only exhibits a low enforcement rate, but also induces unnecessary safety and delay concerns. Since vehicles with six passengers or higher are permitted to enter freeway bus-only lanes, identifying the number of passengers in a vehicle is a core technology required for a freeway bus-only lane enforcement system. To that end, infrared cameras and the You Only Look Once (YOLOv5) deep learning algorithm were utilized. For assessment of the performance of the developed system, two environments, including a controlled test-bed and a real-world freeway, were used. As a result, the performances under the test-bed and the real-world environments exhibited 7% and 8% errors, respectively, indicating satisfactory outcomes. The developed system would contribute to an efficient freeway bus-only lane operations as well as eliminate safety and delay concerns caused by the current manual enforcement procedures.

• Geomechanics and Engineering
• /
• v.31 no.5
• /
• pp.439-452
• /
• 2022

A forecast of slope behavior during catastrophic events, such as earthquakes is crucial to recognize the risk of slope failure. This paper endeavors to eliminate the significant supposition of predefined slip surfaces in the slope stability analysis, which questions the relevance of simple conventional methods under seismic conditions. To overcome such limitations, a methodology dependent on the slip line hypothesis, which permits an automatic generation of slip surfaces, is embraced to trace the extreme slope face under static and seismic conditions. The effect of earthquakes is considered using the pseudo-static approach. The current outcomes developed from a parametric study endorse a non-linear slope surface as the extreme profile, which is in accordance with the geomorphological aspect of slopes. The proposed methodology is compared with the finite element limit analysis to ensure credibility. Through the design charts obtained from the current investigation, the stability of slopes can be assessed under seismic conditions. It can be observed that the extreme slope profile demands a flat configuration to endure the condition of the limiting equilibrium at a higher level of seismicity. However, a concurrent enhancement in the shear strength of the slope medium suppresses this tendency by offering greater resistance to the seismic inertial forces induced in the medium. Unlike the traditional linear slopes, the extreme slope profiles mostly exhibit a steeper layout over a significant part of the slope height, thus ensuring a more optimized solution to the slope stability problem. Further, the susceptibility of the Longnan slope failure in the Huining-Wudu seismic belt is predicted using the current plasticity approach, which is found to be in close agreement with a case study reported in the literature. Finally, the concept of equivalent single or multi-tiered planar slopes is explored through an example problem, which exhibits the appropriateness of the proposed non-linear slope geometry under actual field conditions.

• Smart Structures and Systems
• /
• v.31 no.4
• /
• pp.365-381
• /
• 2023

The existing vision-based techniques for inspection and condition assessment of civil infrastructure are mostly manual and consequently time-consuming, expensive, subjective, and risky. As a viable alternative, researchers in the past resorted to deep learning-based autonomous damage detection algorithms for expedited post-disaster reconnaissance of structures. Although a number of automatic damage detection algorithms have been proposed, the scarcity of labeled training data remains a major concern. To address this issue, this study proposed a semi-supervised learning (SSL) framework based on consistency regularization and cross-supervision. Image data from post-earthquake reconnaissance, that contains cracks, spalling, and exposed rebars are used to evaluate the proposed solution. Experiments are carried out under different data partition protocols, and it is shown that the proposed SSL method can make use of unlabeled images to enhance the segmentation performance when limited amount of ground truth labels are provided. This study also proposes DeepLab-AASPP and modified versions of U-Net++ based on channel-wise attention mechanism to better segment the components and damage areas from images of reinforced concrete buildings. The channel-wise attention mechanism can effectively improve the performance of the network by dynamically scaling the feature maps so that the networks can focus on more informative feature maps in the concatenation layer. The proposed DeepLab-AASPP achieves the best performance on component segmentation and damage state segmentation tasks with mIoU scores of 0.9850 and 0.7032, respectively. For crack, spalling, and rebar segmentation tasks, modified U-Net++ obtains the best performance with Igou scores (excluding the background pixels) of 0.5449, 0.9375, and 0.5018, respectively. The proposed architectures win the second place in IC-SHM2021 competition in all five tasks of Project 2.

• Korean Journal of Environmental Agriculture
• /
• v.41 no.1
• /
• pp.32-40
• /
• 2022

BACKGROUND: Climate-smart agriculture (CSA) has been proposed for sustainable agriculture and food security in an agricultural ecosystem disturbed by climate change. However, scientific approaches to local agricultural ecosystems to realize CSA are rare. This study attempted to evaluate the weather condition, rice production, and greenhouse gas emissions from the rice cultivation in Hwaseong-si, Gyeonggi-do to fulfill CSA of the rice cultivation. METHODS AND RESULTS: Over the past 3 years (2017~2019), Chucheong rice cultivar yield and methane emissions were analyzed from the rice field plot (37°13'15"N, 127° 02'22"E) in the Gyeonggi-do Agricultural Research and Extension Services located in Gisan-dong, Hwaseong-si, Gyeonggi-do. Methane samples were collected from three automated closed chambers installed in the plot. The weather data measured through automatic weather station located in near the plot were analyzed. CONCLUSION(S): The rice productivity was found to vary with weather environment in the agricultural ecosystem. And methane emissions are high in a favorable weather condition for rice growth. Therefore, it is necessary to minimize the trade-off between the greenhouse gas emission target for climate change mitigation and productivity improvement for CSA in a local rice cultivation.