• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.3
• /
• pp.106-111
• /
• 2001

The freestanding GaN substrates were grown by hydride vapor phase epitaxy (HVPE) on (0001) sapphire substrate and prepared by using laser induced lift-off. After a mechanical polishing on both Ga and N-surfaces of GaN films with 100$\mu\textrm{m}$ thick, their polarities have been investigated by using chemical etching in phosphoric acid solution, 3 dimensional surface profiler and Auger electron spectroscopy (AES). The composition of the GaN film measured by AES indicted that Ga and N terminated surfaces have the different N/Ga peak ratio of 0.74 and 0.97, respectively. Ga-face and N-face of GaN revealed quite different chemical properties: the polar surfaces corresponding to (0001) plane are resistant to a phosphoric acid etching whereas N-polar surfaces corresponding to(0001) are chemically active.

• KSTLE International Journal
• /
• v.6 no.2
• /
• pp.39-44
• /
• 2005

Friction and wear properties of the Boron carbide ($B_{4}C$) coating 100 nm thickness were studied under various relative humidity (RH). The boron carbide film was deposited on silicon substrate by DC magnetron sputtering method using $B_{4}C$ target with a mixture of Ar and methane ($CH_4$) as precursor gas. Friction tests were performed using a reciprocation type friction tester at ambient environment. Steel balls of 3 mm in diameter were used as counter-specimen. The results indicated that relative humidity strongly affected the tribological properties of boron carbide coating. Friction coefficient decreased from 0.42 to 0.09 as the relative humidity increased from $5\%$ to $85\%$. Confocal microscopy was used to observe worn surfaces of the coating and wear scars on steel balls after the tests. It showed that both the coating surface and the ball were significantly worn-out even though boron carbide is much harder than the steel. Moreover, at low humidity ($5\%$) the boron carbide showed poor wear resistance which resulted in the complete removal of coating layer, whereas at the medium and high humidity conditions, it was not. X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) analyses were performed to characterize the chemical composition of the worn surfaces. We suggest that tribochemical reactions occurred during sliding in moisture air to form boric acid on the worn surface of the coating. The boric acid and the tribochemcal layer that formed on steel ball resulted in low friction and wear of boron carbide coating.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.301-304
• /
• 2007

다결정 태양전지의 원료인 폴리실리콘을 생산하는 방법 중 하나인 지멘스 방법에서 사용되는 실리콘 코어로드를 금속 계열의 코어로드로 대체하기 위한 연구를 진행하였다. 본 연구에서는 실리콘 코어로드의 대체물질 후보로서 고융점 금속인 텅스텐, 탄탈륨, 몰리브덴을 선택하였고, co-sputtering system을 이용하여 다성분계의 박막을 실리콘 기판에 증착시켜 $800^{cdot}C$에서 $1000^{cdot}C$의 고온에서 열처리 후 박막의 형상변화 및 확산정도를 관찰하였다. 열처리 온도에 따른 박막의 형상 및 확산 정도를 관찰하기 위하여 Scanning electron microscopy (SEM), X-ray diffractometer(XRD), transmission electron microscopy(TEM), auger electron spectroscopy(AES)가 사용되었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.2
• /
• pp.93-97
• /
• 2010

We have studied the effect of the chemical composition of the ZnO nanorod surface on the optical characteristics. The surface was treated with H- and O-plasma at different surface temperatures. The chemical composition of the surface of the ZnO nanorod, being investigated by Auger Electron Spectroscopy(AES), was related to the Photoluminescence(PL) data reported in our previous results. The AES showed the opposite results for the $H_2$ and $O_2$ plasma treatments. The ratio of Zn to O on the surface of the ZnO nanorod increased in the case of $H_2$ plasma, while the composition rate of O increased after $O_2$ plasma treatment. The AES results seems to be correlated to the shift in PL peaks. The increase in the composition rate of Zn on the surface of ZnO nanorod is considered to cause the blue shift of the UV peak. On the contrary, the relative increase of O is considered to cause the red shift in PL peaks.

• Journal of the Korean Vacuum Society
• /
• v.7 no.3
• /
• pp.176-186
• /
• 1998

Pure Pt, Co and their alloy thin films with three different compositions (Pt66-Co34, Pt40-Co60 and Pt18-Co82) were deposited on Si(100) wafers and proposed as a set of certified reference materials (CRM) for the quantification and standardization of surface compositional analysis. The compositions of the binary alloy thin films were controlled by in-situ XPS analyses and the certified compositions of the films have been determined by ICP-AES and RBS analyses after thin film growth. Through comparison of the compositions determined by in-situ XPS with those by ICP, relatively accurate compositions could be obtained with a matrix effect correction. Standard deviations of XPS and AES round robin tests with the Pt-Co alloy thin films were large up to about 4%. On the other hand, the average compositions of the Pt-Co alloy thin films by two methods were in a good agreement within 1%. The formation of a Pt rich surface layer by ion beam sputtering indicates that the surface modification by preferential sputtering must be understood for a better compositional analysis.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4B
• /
• pp.514-518
• /
• 1999

Gold (Au) is not supposed to react with sapphire(single crystalline ) under thermodynamic equillibrium, therefore, a strong adhesion between these two dissimilar materials is not expected. However, pull test showed that the gold film sputter-deposited onto annealed and pre-sputtered sapphire exhibited very strong adhesion even without post-deposition annealing. Strongly and weakly adhered samples as a result of the pull testing were selected to investigate the adhesion mechanisms with Auger electron spectroscopy. The Au/ interfaces were analyzed using a new technique that probes the interface on the film using Auger electron escape depth. It revealed that one or two monolayers of Au-Al-O compound formed at the Au/Sapphire interface when AES in the UHV chamber. It showed that metallic aluminum was detected on the surface of sapphire substrates after irradiating for 3 min. with 7keV Ar+ -ions. These results agree with TRIM calculations that yield preferential ion-beam etching. It is concluded that the formation of Au-Al-O compound, which is responsible for the strong metal-ceramic bonding, is due to ion-induced cleaning and reduction of the sapphire surface, and the kinetic energy of depositing gold atoms, molecules, and micro-particles as a driving force for the inter-facial reaction.

• Transactions on Electrical and Electronic Materials
• /
• v.3 no.3
• /
• pp.29-33
• /
• 2002

A procedure was developed for preparing bulk carbon nitride crystals from a polymeric $\alpha$ -C$_3$N$\_$4.2/ at high pressure and temperature in the presence of seeds of crystalline carbon nitride films prepared by a high voltage discharge plasma combined with pulsed laser ablation of graphite target. The samples were evaluated by x-ray photoelectron spectroscopy (XPS), infrared (IR) spectroscopy, Auger electron spectroscopy (AES), secondary-ion mass spectrometry (SIMS), scanning electron microscopy (SEM) and x-ray diffraction (XRD). Notably, XPS studies of the film composition before and after thermobaric treatments demonstrate that the nitrogen composition in $\alpha$ -C$_3$N$\_$4.2/ material initially containing more than 58% nitrogen decreases during the annealing process and reaches a common, stable composition of ~45%. The thermobaric experiments were performed at 10-77 kbar and 350-1200 $\^{C}$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.10
• /
• pp.747-751
• /
• 2010

In the study, the characteristics of the etched Zinc oxide (ZnO) thin films surface, the etch rate of ZnO thin film in $Cl_2/BCl_3/Ar$ plasma was investigated. The maximum ZnO etch rate of 53 nm/min was obtained for $Cl_2/BCl_3/Ar$=3:16:4 sccm gas mixture. According to the x-ray diffraction (XRD) and atomic force microscopy (AFM), the etched ZnO thin film was investigated to the chemical reaction of the ZnO surface in $Cl_2/BCl_3/Ar$ plasma. The field emission auger electron spectroscopy (FE-AES) analysis showed an elemental analysis from the etched surfaces. According to the etching time, the ZnO thin film of etched was obtained to The AES depth-profile analysis. We used to atomic force microscopy to determine the roughness of the surface. So, the root mean square of ZnO thin film was 17.02 in $Cl_2/BCl_3/Ar$ plasma. Based on these data, the ion-assisted chemical reaction was proposed as the main etch mechanism for the plasmas.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1994.02a
• /
• pp.35-35
• /
• 1994

The surface segragation of NiZr, CuZr alloy has been studied wi th X-ray Imotoelectron spectroscopy(XPS), Auger electron spectroscopy(AES) and low energy ion scattering(LEIS). The composition of outmost atomic layer has been determinded by the use of LEIS at several incident energies using Ar+ ion. In the LEIS analysis, the effect of charge exchange has been estimated by a novel measurment of the charge exchange parameters while simul taneous determining the relative concentrations of Ni and Zr and the complementary information obtained will be described. The composition of the clean annealed surface, measured with AES only, will be contrasted wi th the surface concentration of the preferentially sputtered surface. The experimental results has been clearly demonstrated that when the NiZr ruld CuZr alloys are exposed to continuous Ar+ ion bombardment the outermost atomic layer is Zr rich due to preferential sputtering of Ni atoms. where Ni is preferentially sputtered, but the difference in sputtering yields is not sufficient to explain the observed composition. Therefore, it is necessary to consider other processes such as Radiation Induced Segregation(RIS). The surface composition of the heated sample surface predicts that Zr should surface segregate which futher supports the view that part of the Zr enrichment is due to RIS.to RIS.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.4
• /
• pp.221-225
• /
• 2014

Although gold wire bonding techniques have already matured in semiconductor manufacturing, weakly bonded wires in semiconductor chip assembly can jeopardize the reliability of the final product. In this paper, weakly bonded or failed aluminum bonding pads are analyzed using X-ray photoelectron spectroscopy (XPS), Auger electron Spectroscopy (AES), and energy dispersive X-ray analysis (EDX) to investigate potential contaminants on the bond pad. We found the source of contaminants is related to the dry etching process in the previous manufacturing step, and fluorocarbon plasma etching of a passivation layer showed meaningful evidence of the formation of fluorinated by-products of $AlF_x$ on the bond pads. Surface analysis of the contaminated aluminum layer revealed the presence of fluorinated compounds $AlOF_x$, $Al(OF)_x$, $Al(OH)_x$, and $CF_x$.