• 센서학회지
• /
• 제14권2호
• /
• pp.131-135
• /
• 2005

This paper describes the ohmic contact formation of single crystalline 3C-SiC thin films heteroepitaxially grown on Si(001) wafers. In this work, a TiW (Titanium-tungsten) film as a contact matieral was deposited by RF magnetron sputter and annealed with the vacuum and RTA (rapid thermal anneal) process respectively. Contact resistivities between the TiW film and the n-type 3C-SiC substrate were measured by the C-TLM (circular transmission line model) method. The contact phases and interface the TiW/3C-SiC were evaulated with XRD (X-ray diffraction), SEM (scanning electron microscope) and AES (Auger electron spectroscopy) depth-profiles, respectively. The TiW film annealed at $1000^{\circ}C$ for 45 sec with the RTA play am important role in formation of ohmic contact with the 3C-SiC substrate and the contact resistance is less than $4.62{\times}10^{-4}{\Omega}{\cdot}cm^{2}$. Moreover, the inter-diffusion at TiW/3C-SiC interface was not generated during before and after annealing, and kept stable state. Therefore, the ohmic contact formation technology of single crystalline 3C-SiC using the TiW film is very suitable for high temperature MEMS applications.

• 정보저장시스템학회논문집
• /
• 제2권2호
• /
• pp.123-129
• /
• 2006

The head to disk spacing must be decreased to increase recording densities in hard disk drives. Recently, to decrease the head to disk spacing, smooth disk having no bumps onto the lading zone has used. In this research, we compared the number of particles generated ill HDD with smooth and textured disks. We used a sampling method using a particle sampler and a CPC (condensation particle counter) to detect particles in HDD. First, we sampled and counted particles generated with disk rotational speed and various rest times when the smooth disk and textured disks were used, then analyzed the sampled particles by SEM (scanning electron microscopy) and AES (auger electron spectroscopy). In results of measuring particles, more particles in case of LZT disk drive generated than that of the smooth disk drive in all test modes. The number of particles generated in the smooth disk was very low. The particle generation increased as the rest time increased (smooth/LZT disks) and more particles in case of LZT disk drive generated than that of the smooth disk drive. In results of analyzing particle components, Al, Ti, Si components were detected and we could not found differences between components in case of smooth/LZT disk drive.

• 한국표면공학회지
• /
• 제27권5호
• /
• pp.253-260
• /
• 1994

Ta-N films were reactively sputter deposited by dc magnetron sputtering from a Ta target with a various Ar-N, gas ratio. Electrical resistivity of pure Ta film was 150$\mu$$\Omega$cm and decreased initially with nitrogen addition, and then increased to a value of 220$\mu$$\Omega$-cm~260$\mu$$\Omega$-cm at 9%~23% nitrogen partial flow. Rutherford backscattering spectrometry(RBS) and Auger electron spectroscopy (AES) analysis show that nitrogen content in the film is increased with the nitrogen partial flow. The film contains 58at.% nitrogen at 36% nitrogen partial flow. Both the phase and the microstructure of the as-deposisted films were investigated by x-ray diffractometry(XRD) adn transmission electron microscopy (TEM) at various nitrogen content. The phase of pure Ta film is identified as $\beta$-Ta with a 200$\AA$~300$\AA$ grain size. The phase of Ta film is changed to bcc-Ta as small amount of nitrogen is added. Crystalline Ta2N film was deposited at 24at.% nitrogen content. Amorphous phase is formed over a range of nitrogen content from about 33at.% to 35at.% while crystalline fcc-TaN is observed to form at 39at.%~48at.% nitrogen content.

• 한국자기학회지
• /
• 제11권4호
• /
• pp.163-167
• /
• 2001

DC 마그네트론 스퍼터링법으로 증착된 700 $\AA$의 NiFe 박막을 박막 증착시 형성시킨 자화용이축에 수직한 자기장을 인가하여 열처리한 후 일축 이방성 자기장의 회전을 조사하였다. NiFe 박막은 열처리온도 160 $^{\circ}C$에서 자화용이축과 자화곤란축을 구분할 수 없는 등방적인 상태가 되었고, 열처리온도가 증가함에 따라 다시 일축 이방성을 갖는 상태가 되었다. 열처리 온도가 400 $^{\circ}C$ 이상인 경우에 급격한 보자력의 증가를 보였다. 열처리 온도가 400 $^{\circ}C$인 경우에 XRD 분석과 AES depth profile은 NiFe 박막 내에서 (111) 방향으로 결정성장이 활발히 일어나며 인접한 전극 Au와 상호화산 현상도 광범위하게 일어남을 보여주었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.88-88
• /
• 2011

ZnO는 직접 천이형 반도체로써, 상온에서 3.4eV에 해당하는 띠틈을 가지고 있다. 뿐만 아니라 60meV의 큰 엑시톤 결합에너지를 가지고 있어 단파장 광전 소자 영역의 LED(Light Emitting Diode)나 LD(Laser Diode)에 널리 사용되고 있다. 하지만 일반적으로 격자틈새 Zn(Zni2+)이온이나 O 빈자리(V02+)이온과 같은 자연적인 도너 이온이 존재하여 n-형 전도성을 나타낸다. 그러므로 ZnO계 LED와 LD의 개발에 있어서 가장 중요한 연구 과제는 재현성 있고 안정된 고농도의 p-형 ZnO박막을 성장시키는 것이다. 하지만, 자기보상효과나 얕은 억셉터 준위, 억셉터의 낮은 용해도로 인하여 어려움을 가지고 있다. 본 연구에서는 고품질의 p-형 ZnO박막을 제작하기 위해 AlN를 도핑시킨 ZnO박막을 RF 마그네트론 스퍼터링 법을 이용하여 Ar과 O2분위기에서 성장시켰다. ZnO와 AlN타겟을 동시에 사용하였으며, ZnO타겟에 걸어준 RF 파워는 80W, AlN타겟에 걸어준 RF 파워는 5~20W로 변화시켰다. 박막의 전기적, 광학적 특성은 XPS (X-ray Photoelectron Spectroscopy), REELS (Reflection Electron Energy Loss Spectroscopy), XRD (X-ray Diffraction), SIMS (Secondary Ion Mass Spectrometry), AES (Auger Electron Spectroscopy), Hall measurement를 이용하여 연구하였다. XPS측정결과, AlN를 도핑시킨 ZnO박막의 Zn2p3/2와 O1s피크는 undoped ZnO박막의 피크보다 낮은 결합에너지에서 측정되었다. 모든 박막이 결정화 되었으며, (002)방향으로 우선적으로 성장된 것을 확인할 수 있었다. 홀 측정 결과, 기판을 $200^{\circ}C$로 가열하면서 성장시킨 박막이 p-형을 나타내었으며, 비저항(Resistivity)이 $5.51{\times}10^{-3}{\Omega}{\cdot}m$, 캐리어 농도(Carrier Concentration)가 $1.96{\times}1018cm^{-3}$, 이동도(Mobility)가 $481cm^2$/Vs이었다. 또한 QUEELS -Simulation에 의한 광학적 특성분석 결과, 가시광선영역에서 투과율이 90%이상으로 투명전자소자로의 응용이 가능하다는 것을 보여주었다.

• 대한금속재료학회지
• /
• 제49권4호
• /
• pp.313-320
• /
• 2011

100 nm-thick hydrogenated amorphous silicon $({\alpha}-Si:H)$ films were deposited on a glass and glass/30 nm Ni substrates by inductively-coupled plasma chemical vapor deposition (ICP-CVD) at temperatures ranging from 100 to $550^{\circ}C$. The sheet resistance, microstructure, phase transformation and surface roughness of the films were characterized using a four-point probe, AFM (atomic force microscope), TEM (transmission electron microscope), AES (Auger electron spectroscopy), HR-XRD(high resolution X-ray diffraction), and micro-Raman spectroscopy. A nano-thick NiSi phase was formed at substrate temperatures >$400^{\circ}C$. AFM confirmed that the surface roughness did not change as the substrate temperature increased, but it increased abruptly to 6.6 nm above $400^{\circ}C$ on the glass/30 nm Ni substrates. HR-XRD and micro-Raman spectroscopy showed that all the Si samples were amorphous on the glass substrates, whereas crystalline silicon appeared at $550^{\circ}C$ on the glass/30 nm Ni substrates. These results show that crystalline NiSi and Si can be prepared simultaneously on Ni-inserted substrates.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 하계종합학술대회 논문집(2)
• /
• pp.32-35
• /
• 2000

Oxide-nitride-oxide(ONO) structures were formed by sequential radio frequency reactive magnetron sputtering method. The chemical composition and structure of these films were studied by using of secondary ion mass spectroscopy(SIMS) and Auger electron spectroscopy(AES) SIMS and AES experiments show the existence of nitridation at the SiO$_2$/Si substrate. The electrical characteristics of ONO films were evaluated by I-V and high frequency C-V measurements When the ONO films were annealed at 90$0^{\circ}C$ for 30 sec in $N_2$ ambient, the breakdown voltage increased and flat-band voltage decreased under high electric field.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1998년도 제14회 학술발표회 논문개요집
• /
• pp.20-20
• /
• 1998

I Ion beam technology has recently attracted much interest because it has exciting t technological p아:ential for surface analysis, ion beam mixing, surface cleaning and etching i in thin film growth and semiconductor fabrication processes, etc. Es야~cially, ion beam s sputtering has been widely used for sputter depth profiling with x-photoelectron S spectroscopy (XPS) , Auger electron s$\pi$~troscopy(AES), and secondary-ion mass S야i따oscopy(SIMS). However, The problem of surface compositional ch없1ge due to ion b bombardment remains to be understo여 없ld solved. So far sputtering processes have been s studied by s따face an외ysis tools such as XPS, AES, and SIMS which use the sputtering p process again. It would be improbable to measure the modified surface composition profiles a accurately due to ion beam bombardment with surface analysis techniques based on sputter d depth profiling. However, recently Medium energy ion scattering spectroscopy(MEIS) has b been applied to study the sputtering of solid surface at ion bombardment and has been p proved that it has been extremely valuable in probing the surface composition 뻐d s structure nondestructively and quantita디vely with less than 1.0 nm depth resolution. To u understand the sputtering processes of solid surface at ion bombardment, The Molecular D Dynamics(MD) and Monte Carlo(MC) simulation has been used and give an intimate i insight into the sputtering processes of solid surfaces. In this presentation, the sputtering processes of alloys and compound samples at ion b bombardment will be reviewed and the MEIS results for the Ar+ sputter induced altered l layer of the TazOs thin film 뻐dd없nage profiling of Ar+ ion sputt얹"ed Si(100) surface will b be discussed with the results of MD and MC simulation.tion.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.141-141
• /
• 1999

전기화학과 초고진공(ultra-high vacuum, UHV) 분광법을 이용하여 고체/액체의 계면에서 일어나는 현상을 분자단위에서 이해하고 조절하기 위한 연구를 수행하였다. 이들 중 전기화학으로 형성된 구리 및 은 금속(sub)monlayer 박막을 그 예로 선택하여 소개한다. 초박막 금속의 흡착량은 cyclic voltammogram과 새로 개발된 Auger electron spectroscopy (AES) 정량법을 통해 얻어졌고, 이 값들은 low energy electron diffraction (LEED) 및 in-situ atomic force microscopy (AFM)법을 이용한 구조 분석결과와 비교되어졌다. 또한 화학상태를 확인하기 위하여 core-level electron energyy loss spectroscopy (CEELS)를 사용하였다. 먼저 황산 전해질에서 금(111) 단결정 전극상에 전기화학적으로 형성된 굴의 계면특성을 조사하였다. 특정 전위값에서 2/3 ML의 구리와 1/3 ML의 음이온이 상호 흡착하여 ({{{{ SQRT { 3} }}$\times${{{{ SQRT { 3} }}) 격자 구조를 보였고, 전위값이 커지거나 줄어들면, 이 구조가 사라지는 현상이 관찰되었다. 즉 이 ({{{{ SQRT { 3} }}}}$\times${{{{ SQRT { 3} }}}}) 흡착구조는 첫 번째 UPD underpotential deposition) 피크에 특이하게 관련되어 있음을 알 수 있었다. 금속 초박막 형성에 미치는 음이온의 영향을 좀 더 확인하기 위해 초박막 은이 증착된 금 단결정 전극상의 황산 음이온에 관하여 연구하였다. 은의 증착이 일어날 수 없는 양전위값 영역에서 ({{{{ SQRT { 3} }}}}$\times${{{{ SQRT { 3} }}}})의 규칙적인 음이온의 구조를 보였다. 그리고 은의 장착은 세척 과정과 용액의 농도에 따라 p(3$\times$3)과 p(5$\times$5)의 규칙적인 두가지 구조를 가졌다. in-situ AFM에서는 p(3$\times$3)의 은 증착 구조만 나타났고, 음 전위값으로 옮겨가면 p(1$\times$1) 구조로 바뀌었다. ex-situ 초고진공 결과와 이 AFM의 in-situ 결과를 상호 비교 논의할 것이다. 음이온의 흡착이 없는 묽은 플로르산(HF) 전해질에서 은은 전위값을 음전위 쪽으로 이동해 감에 따라 p(3$\times$3), p(5$\times$5), (5$\times$5), (6$\times$6), 그리고 (1$\times$1)의 연속적 구조 변화를 보였다. 이 다양한 구조들을 AES로부터 얻어진 표면 흡착량과 연결시켰더니 정량적으로 잘 일치되는 결과를 보였다. 전기화학적인 증착에서는 기존의 진공 증착과 비교할 때 음이온의 공흡착이 금속 초박막 형성 메카니즘에 큰 영향을 미침을 알 수 있었다. 또한 은의 전기화학적 다층박막 성장은 MSM (monolayer-simultaneous-multilayer) 메카니즘을 따름을 확인하였다. 마지막으로 구조 및 양이 규칙적으로 조절되는 전극의 응용가능성이 간단히 논의될 것이다.

• 한국표면공학회지
• /
• 제34권2호
• /
• pp.89-96
• /
• 2001

N- or O-doped STS304 stainless films were synthesized by an unbalanced magnetron sputtering process with various argon and reactive gas ($N_2$, $O_2$) mixtures. These films were examined by scanning electron microscopy (SEM), X-ray diffraction (XRD), Auger electron spectroscopy (AES) and Knoop microhardness tester. The Results from X-ray diffraction (XRD) analysis showed that a STS304 stainless steel film synthesized without reactive gas using a bulk STS304 stainless steel target had a ferrite bcc structure ($\alpha$ phase), while the N-doped STS304 stainless film was consisted of a nitrogen supersaturated fcc structure, which hsa a strong ${\gamma}$(200) phase. In the O-doped films, oxide Phases ($Fe_2$$O_3$ and $Cr_2$$O_3$) were observed from the films synthesized under an excess $O_2$ flow rate of 9sccm. AES analysis showed that nitrogen content in N-doped films increased as the nitrogen flow rate increased. Approximately 43 at.%N in the N-doped film was measured using a nitrogen flow rate of 8sccm. In O-doped film, approximately 15 at.%O was detected using a $O_2$ flow rate of 12sccm. the Knoop microhardness value of N-doped film using a nitrogen flow rate of 8 sccm was measured to be approximately $H_{ k}$ 1200 and this high value could be attributed to the fine grain size and increased residual stress in the N-doped film.