• Korean Journal of Materials Research
• /
• v.6 no.2
• /
• pp.158-165
• /
• 1996

열증착기(thermal evaporator)로 증착시킨 Cu를 상온에서 3.5M CuCl2+0.5M HCI+0.5MKCI 용액을 사용하여 습식각하고 2일간 대기중 노출시킨 후 X-선 광전자 분광기를 이용하여 표면의 결합상태를 관찰하였다. 그 결과 습식식각된 Cu 표면에서는 C, O, Ci 및 Cu가 존재함을 알 수 있었다. 표면원소에 대한 오제이 전자 스펙트라(Auger electron spectra)와 광전자 스펙트라(photoelectron spectra)의 정량적인 비교를 통하여 표면의 모든 결합상태를 확인할 수 있었고 그 상대적인 양까지도 얻어낼 수 있었다. 식각된 Cu의 표면에는 Cu-Cu, 2Cu-O, Cu-Ci, Cu-2(OH), 및 Cu-2Cl의 결합상태가 존재함을 알 수 있었고, CuLMMAuger line spectrum의 관찰을 통하여 계산된 각 결합의 정량적인 비교를 검증할 수 있었다. 따라서 chemical shift가 거의 관찰되지 않아 결합상태 분리가 불가능한 식각된 구리표면의 정량적 결합상태는 각 결합상태의 상대적 비교를 통하여 얻어질 수 있음을 알 수 있었다.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.175-176
• /
• 2002

Our study is to search for tribological properties of diamond-like carbon (DLC) films as known as anti- wear hard thin film on various polymers. This report deals with the deposition of DLC films on various polymer substrates in vacuum by magnetron radio frequency (RF) sputtering method with using argon plasma and graphite, titanium target. The properties of friction and wear are measured using a ball-on-disk wear -testing machine. The properties of friction and wear have been remarkably improved by DLC coating. Moreover the composition of DLC films has been analyzed by using auger electron spectroscopy(AES). The wear rate of titanium-containing DLC film is lower than that of no-metal-containing DLC film.

• Korean Journal of Materials Research
• /
• v.7 no.2
• /
• pp.162-170
• /
• 1997

This study has evaluated the dissimialr weldability of Incoloy 825 Ni base alloy with a mild steel(SS41). Further a compatibility study of wrveral Ni base filler metals with the dissimilar joint between the two alloys was also included. The dissimilar weldability of Incoloy 825 with mild steel is strongly dependent upon the type of the filler metal used. Among the filler metals, ENiCrFe which has a chemical comosition similar to that of Incoloy 825 was found to be most compatible to the joint. In addition, a filler metal which showed a good cracing resistance in one dissimiar alloy combination was not necessarily graranteed to other combination. Microstructural examination with SEM, TEM and Auger revealed that the solidification cracking resestance of the dissimilar joint. between Incoloy 835 and SS41 was closely with the Ti+Nb content and with the content of a low melting eutectic phase of Laves relatibve to that of MC type phase.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.267-267
• /
• 2009

Solar cells with CIGS absorber layers have proven their suitability for high efficiency and stable low cost solar cells. We prepared and characterized particle based CIGS thin film using a non-vacuum processing. CIGS powder were obtained at $240^{\circ}C$ for 6 hours from the reaction of $CuCl_2$, $InCl_3$, $GaCl_3$, Se powder in solvent. The nanoparticle precursors were mixed with binder material. The CIGS thin film deposited on a sodalime glass. The CIGS thin film were identified to have a typical chalcopyrite tetragonal structure by using UV/Visible-spectroscopy, X-ray diffraction(XRD), Auger Electron Spectroscopy(AES), Scanning Electron Microscopy(SEM).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.229-229
• /
• 2012

Adhesion of Copper film on the aluminum oxide layer formed by anodizing an aluminum plate was enhanced by applying ion beam mixing method. Forming an conductive metal layer on the insulating oxide surface without using adhesive epoxy bonds provide metal-PCB(Printed Circuit Board) better thermal conductivities, which are crucial for high power electric device working condition. IBM (Ion beam mixing) process consists of 3 steps; a preliminary deposition of an film, ion beam bombardment, and additional deposition of film with a proper thickness for the application. For the deposition of the films, e-beam evaporation method was used and 70 KeV N-ions were applied for the ion beam bombardment in this work. Adhesions of the interfaces measured by the adhesive tape test and the pull-off test showed an enhancement with the aid of IBM and the adhesion of the ion-beam-mixed films were commercially acceptable. The mixing feature of the atoms near the interface was studied by scanning electron microscopy, Auger electron spectroscopy, and X-ray photoelectron spectroscopy.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.20-23
• /
• 2000

We have investigated a process for the preparation of high-quality tantalum oxynitride ( $T_{a}$ $O_{x}$ $N_{y}$) via the N $H_3$ annealing of 7$_{a2}$ $O_{5}$, for use in gate dielectric applications. Compared with tantalum oxide (7$_{a2}$ $O_{5}$), a significant improvement in the dielectric constant was obtained by the N $H_3$ treatment. In addition, light reoxidation in a wet ambient at 45$0^{\circ}C$ resulted in a significantly reduced leakage current. We confirmed nitrogen incorporation in the tantalum oxynitride ( $T_{a}$ $O_{x}$ $N_{y}$ by Auger Electron Spectroscopy. By optimizing the nitridation and reoxidation process, we obtained an equivalent oxide thickness as thin as 1.6nm and a leakage current of less than 10mA/$\textrm{cm}^2$ at 1.5V..5V..5V..5V..5V..5V.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.354.1-354.1
• /
• 2016

Nanoporous gold (NPG) is a very promising material in various fields such as sensor, actuator, and catalysis because of its high surface to volume ratio and conducting nature. In this study, we fabricated a NPG based amperometric sensor on a glass substrate by means of co-sputtering of Au and Si. During the sputtering process, we found the optimum conditions for heat treatment to reduce the residual stress and to improve adhesion between NPG films and the glass substrate. Subsequently, Si was selectively etched from Au-Si alloy by KOH solution, which forms nanoporous structures. Scanning electron microscopy (SEM) and auger electron spectroscopy (AES) were used to estimate the structure of NPG films and their composition. By employing appropriate heat treatments, we could make very stable NPG films. We tested the performance of NPG sensor with aniline molecules, which shows high sensitivity for sensing low concentration of aniline.

• Applied Microscopy
• /
• v.45 no.4
• /
• pp.214-217
• /
• 2015

This study introduces metal coating as an effective sample preparation method to remove charge-up caused by the shadow effect during field emission scanning electron microscope (FE-SEM) analysis of dynamic structured samples. During a FE-SEM analysis, charge-up occurs when the primary electrons (input electrons) that scan the specimens are not equal to the output electrons (secondary electrons, backscattered electrons, auger electrons, etc.) generated from the specimens. To remove charge-up, a metal layer of Pt, Au or Pd is applied on the surface of the sample. However, in some cases, charge-up still occurs due to the shadow effect. This study developed a coating method that effectively removes charge-up. By creating a converted sample stage capable of simultaneous tilt and rotation, the shadow effect was successfully removed, and image data without charge-up were obtained.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.442-443
• /
• 2009

We prepared and characterized particle based CIGS thin film using a thermal evaporator. CIGS powder were obtained at $240^{\circ}C$ for 6 hours from the reaction of $CuCl_2$, $InCl_3$, $GaCl_3$, Se powder in solvent. The CIGS thin film deposited on a sodalime glass. The CIGS thin film were identified to have a typical chalcopyrite tetragonal structure by using UV/Vis-spectroscopy, X-ray diffraction(XRD), Auger Electron Spectroscopy(AES), Scanning Electron Microscopy(SEM).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.8
• /
• pp.734-739
• /
• 2005

Zinc oxide films were deposited on Si (111) substrates by radio-frequency (rf)sputtering at a room temperature and post annealed in Na, air, and $H_2O$ ambient at temperatures between $800{\circ}C$ for 2 hrs. The properties were investigated by atomic force microscope (AFM), X-ray diffraction (XRD), Auger electron spectroscopy (AES) and photoluminescence (PL). Our experiments demonstrated that ZnO films have the better crystal quality for post thermal annealing and especially in $H_2O$ ambient. Even though thermal annealing reduced deep level emission somewhat, for further getting rid off deep level emission, oxygen contents should be adjusted. In our results, $H_2O$ ambient gave the best structural and optical properties.