• Journal of IKEEE
• /
• v.6 no.2 s.11
• /
• pp.119-127
• /
• 2002

An algorithm for analyzing the characteristics of the power BJT using numerical analysis method is proposed. The Fermi-Dirac statistics is used to calculate the carrier concentration in highly doped region. Philips Unified mobility model, SRH model and Auger model is used to calculate the recombination current of base region. To verify the accuracy of the proposed method, the collector current of BANDIS is compared with the measured data in the condition of the base current increased from $1.0[{\mu}A]\;to\;3.5[{\mu}A]$. The collector current of BANDIS show a maximum relative error within 8.9% compared with the measured data.

• Journal of the Korean GEO-environmental Society
• /
• v.3 no.2
• /
• pp.15-21
• /
• 2002

Because of the environmental problem during the pile driving, the use of low noise-vibration auger-drilled pilling is increasing to solve noise and vibration problem in pilling. In Korea, SIP (Soil-Cement Injected Precast Pile) method is mainly used as auger-drilled pilling. But, a proper bearing capacity evaluation formula has not been suggested, yet. To improve and supplement this situation, direct shear tests between SIP pile skin interface and soil were executed under various conditions. Through the analysis of test results, skin resistance characteristics of SIP were investigated thoroughly. Also, the maximum unit skin resistance capacity evaluation formulae on SM, SC soil was suggested.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.403-403
• /
• 2008

This article reports changes in the mechanical properties of chromium steel after nitrogen implantation at high temperature. The samples are implanted with 120keV N-ion at doses ranging from $1\times1080$ to $4\times1080ions/cm^2$ and at substrate temperature ranging from 25 to $400^{\circ}C$. Nano-hardness and AES(Auger electrons spectroscopy) were measured from nitrogen ion implanted layer. The sliding wear and impact wear properties of the implanted samples were also measured. The results revealed that the hardness and mechanical properties of ion implanted samples depend strongly on the ion doses and implantation temperature. The hardness of the nitrogen implanted sample with 120keV, $4\times10^{18}ions/cm^2$, $335^{\circ}C$ was measured to be approximately 20 GPa, which is approximately 5 times higher than that of un-implanted sample (H=3.8 GPa). Also, the sliding wear and impact wear properties of nitrogen implanted samples were greatly improved. Detailed experiment results will be presented.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.66-66
• /
• 2000

Electrochromism이란 기전력 방향에 의한 가역적으로 색이 변하는 현상을 말하며, 열린 회로 기억성을 가지며 소비전력이 적고, 우수한 착색 효율을 갖는 등 여러 가지 유용성 때문에 디스플레이 및 전기적 착색 유리창에의 기술적 적용 가능성을 보이고 있다. 본 연구에서는 가장 우수한 일렉트로크로믹 특성을 내는 것으로 알려진 WO3 박막과 대향 전극으로 V2O5 박막을 사용하였다. 이들 박막은 알칼리 이온 주입물질이며, coloration.bleaching상태에서 광학 밀도가 크고, 내구성이 좋으며, 작은 비용으로 재료를 사용할 수 있다. 그리고 더 우수한 장점으로 부각되는 대면적의 코팅의 매력적인 기술인 졸겔법으로 제조 가능한 특성을 가지고 있다. 졸겔법 및 진공증착법으로 박막을 제조하고, 박막산화 및 수명저하 등의 위험이 적은 리튬이온을 이용하여 소자를 제작한 후 일렉트로크로믹 특성을 조사하고, 우수한 소자의 제조조건을 얻고자 하였다. 측정결과 졸겔법으로 제조된 WO3 박막과 V2O5 박막을 수증기 분위기에서 50$0^{\circ}C$로 1시간 열처리한 경우 가장 우수한 투과 변화율을 나타내었다. 정상전압인 2 volt보다 높은 3 volt로 cyclic voltamogram을 측정하는 과정에서 정.역방향 동작을 거듭할수록 peak이 크게 감소하는 현상을 발견하였으며, 양이온의 흐름에 의해 물질의 이동이 발생할 것이라는 판단아래 Auger depth profile을 측정한 결과 WO3막의 텅스텐과 ITO막의 인듐이 상호 확산하는 것을 관찰할 수 있었다. 이를 방지하기 위해 수백 의 텅스텐 박막을 WO3 막 위에 증착한 후 cyclic voltamogram과 Auger depth profile을 측정한 결과, cyclic voltamogram의 peak의 감소량이 1/10이하로 감호하였으며, 리튬이온의 흐름에 의한 인듐과 텅스텐의 이동을 효과적으로 방지할 수 있었다. 따라서 텅스텐 확산방지막의 삽입이 소자의 수명을 향상시킬 수 있는 효과적인 방법이라고 사료된다.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.78-84
• /
• 2003

Boron carbide thin coatings were deposited on silicon wafers by DC magnetron sputtering using a $B_4C$ target with As as processing gas. Various amounts of methane gas $(CH_4)$ were added in the deposition process to better understand their influence on tribological properties of the coatings. Reciprocating wear tests employing an oscillating friction wear tester were performed to investigate the tribological behaviors of the coatings in ambient environment. The chemical characteristics of the coatings and worn surfaces were studied using X-ray Photoelectron Spectroscopy (XPS) and Auger Electron Spectroscopy (AES). It revealed that $CH_4$ addition to As processing gas strongly affected the tribologcal properties of sputtered boron carbide coating. The coefficient of friction was reduced approximately from 0.4 to 0.1, and wear resistance was improved considerably by increasing the ratio of $CH_4$, gas component from 0 to $1.2\;vol\;\%$. By adding a sufficient amount of $CH_4\;(1.2\%)$ in the deposition process, the boron carbide coating exhibited lowest friction and highest wear resistance.

• Korean Journal of Materials Research
• /
• v.4 no.3
• /
• pp.329-333
• /
• 1994

A large number of grain boundaries were seen to crack in near-eutectic solder joints of leadless ceramic chip carriers (LLCC's) during thermal cycling at temperature ranges from -$35^{\circ}C$ to +$125^{\circ}C$ with lhr time period. One potential explanation for this type of cracking might be the presence of embrittling species on the boundary. Although there do not appear to be any instances reported in the literature of solders being embrittled by small amounts of contaminating species, the possibility of such an occurrence exists. The potential presence of impurities located at crack surfaces was inspected using Scanning Auger Microprobe(SAM) and it was found that intergranular cracking could be accomplished by the oxidation of the grain boundary. A physical model for fatigue crack growth was introduced, in which grain boundary separation took place under oxidation facilitated by sliding.

• Journal of the Korean GEO-environmental Society
• /
• v.4 no.1
• /
• pp.59-66
• /
• 2003

The environmental problem due to the pile driving, the use of low noise-vibration auger-drilled pilling is increasing to solve noise and vibration problem in pilling. Therefore, in Korea, SIP (Soil-Cement Injected Precast Pile) method is mainly used as auger-drilled pilling. However, a proper bearing capacity evaluation formula has not been suggested, yet. In order to improve and supplement this situation, direct shear tests between SIP pile skin interface and soil were executed under various conditions. Through the analysis of test results, skin resistance characteristics of SIP were investigated thoroughly. Also, the nonlinear unit skin resistance capacity model and relative parameters evaluation formula with SM, SC soil were suggested.

• Journal of the Korean Chemical Society
• /
• v.28 no.2
• /
• pp.109-113
• /
• 1984

The effects of various supports on the activity and the selectivity for the ethylene oxidation was investigated over$ Ag/{\alpha}-Al_2O_3$ and $Ag/SnO_2$ by Auger, EPR spectroscopy and reaction studies. The results indicate that over $Ag/SnO_2$ catalyst O- chemisorbed on $SnO_2 $participates in the complete oxidation of ethylene lowering the selectivity for the formation of ethylene oxide.

• Journal of the Korean Magnetics Society
• /
• v.20 no.6
• /
• pp.212-215
• /
• 2010

Spin polarized tunneling studies were carried out with Al-Ga bilayer as a spin detector, by Meservey-Tedrow technique. The superconductor (SC)/Insulator (I)/Ferromagnet (FM) tunnel junctions were provided by ultra high vacuum molecular beam epitaxy (UHV-MBE) technique. The analysis of interfacial properties in the Al-Ga bilayer was also carried out by Auger electron spectroscopy. It was observed that the superconducting transition temperature and energy gap were raised in comparison with that of bulk Ga and pure ultrathin Al films. Current studies clearly show how one can modify the material properties at the interface just with a few monolayers.

• Journal of Magnetics
• /
• v.12 no.4
• /
• pp.149-151
• /
• 2007

The AlCrN films were grown by RF reactive sputtering method under the selected conditions. The Cr concentration was varied by the number of Cr pieces placed on the Al target. The sample quality has been studied by XRD, Auger spectroscopy, optical absorption and electrical resistant measurements. The XRD and Auger results show that the samples consist of a major phase with the $Al_{1-x}Cr_xN$ formula, which has a hexagonal structure, and a few percents at. of oxygen, which may form $Al_2O_3$. There exist the Cr clusters in the samples with high concentration of Cr. The optical absorption measurement provides the information about the band gap that relates strongly to the quality of samples. The quality of samples is also clearly reflected in electrical measurement, i.e., the temperature dependence of resistance exhibits a semiconductor characteristic only for the samples that have no Cr cluster. In these cases, the values of ionization energies $E_a$ can be derived from R(T) plots by using the function R(T) = Ro exp $(E_a/k_BT)$.