• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.11
• /
• pp.6-12
• /
• 2010

A sigma-delta modulator based class-D audio amplifier is presented. Parallel digital input is serialized to two-bit output by a fourth-order digital sigma-delta noise shaper. The output of the digital sigma-delta noise shaper is applied to a fourth-order analog sigma-delta modulator whose three-level output drives power switches. The pulse density modulated (PDM) output of the power switches is low-pass filtered by an LC-filter. The PDM output of the power switches is fed back to the input of the analog sigma-delta modulator. The first integrator of the analog sigma-delta modulator is a hybrid of continuous-time (CT) and switched-capacitor (SC) integrator. While the sampled input is applied to SC path, the continuous-time feedback signal is applied to CT path to suppress the noise of the PDM output. The class-D audio amplifier is fabricated in a standard $0.13-{\mu}m$ CMOS process and operates for the signal bandwidth from 100-Hz to 20-kHz. With 4-${\Omega}$ load, the maximum output power is 18.3-mW. The total harmonic distortion plus noise and dynamic range are 0.035-% and 80-dB, respectively. The modulator consumes 457-uW from 1.2-V power supply.

• Journal of Navigation and Port Research
• /
• v.28 no.3
• /
• pp.213-219
• /
• 2004

In this paper, a LNA(Low Noise Amplifier) has been developed, which is operating at L-band i.e., 1452∼1492 MHz for satellite DAB(Digital Audio Brcadcasting) receiver. The LNA is designed to improve input and output reflection coefficient and VSWR(Voltage Standing Wave Ratio) by balanced amplifier. The LNA consists of low noise amplification stage and gain amplification stage, which make a using of GaAs FET ATF-10136 and VNA-25 respectively, and is fabricated by hybrid method. To supply most suitable voltage and current, active bias circuit is designed Active biasing offers the advantage that variations in $V_P$ and $I_{DSS}$ will not necessitate a change in either the source or drain resistor value for a given bias condition. The active bias network automatically sets $V_{gs}$ for the desired drain voltage and drain current. The LNA is fabricated on FR-4 substrate with RF circuit and bias circuit, and integrated in aluminum housing. As a reults, the characteristics of the LNA implemented more than 32 dB in gain. 0.2 dB in gain flatness. lower than 0.95 dB in noise figure, 1.28 and 1.43 each input and output VSWR, and -13 dBm in $P_{1dB}$.

• International Journal of Internet, Broadcasting and Communication
• /
• v.9 no.2
• /
• pp.58-63
• /
• 2017

The sound we hear is transmitted through the atmosphere. However, both the sound we want to hear and the surrounding sound are mixed, and noise is generated, and the sound is not clearly transmitted due to factors such as distance. In particular, in closed spaces like buildings, it is often difficult to hear sounds from outside because of the sound of reflection. People with hearing impairments, such as the elderly and the deaf, have a hard time hearing the sounds they want to hear. Thus, we are developing a hearing aid that can detect radio waves. To this end, we propose the development of a hearing aid that uses FM radio and Bluetooth. These devices are expected to be useful not only for the elderly and the deaf but also in situations where information is transmitted to a large number of people, such as students and tourists, in a large space. The main purpose of this device is to enable users to hear sound correctly without blind spots.

• ETRI Journal
• /
• v.33 no.6
• /
• pp.897-903
• /
• 2011

A hybrid ${\Delta}{\Sigma}$ modulator for audio applications is presented in this paper. The pulse generator for digital-to-analog converter alleviates the requirement of the external clock jitter and calibrates the coefficient variation due to a process shift and temperature changes. The input resistor network in the first integrator offers a gain control function in a dB-linear fashion. Also, careful chopper stabilization implementation using return-to-zero scheme in the first continuous-time integrator minimizes both the influence of flicker noise and inflow noise due to chopping. The chip is implemented in a 0.13 ${\mu}m$ CMOS technology (I/O devices) and occupies an active area of 0.37 $mm^2$. The ${\Delta}{\Sigma}$ modulator achieves a dynamic range (A-weighted) of 97.8 dB and a peak signal-to-noise-plus-distortion ratio of 90.0 dB over an audio bandwidth of 20 kHz with a 4.4 mW power consumption from 3.3 V. Also, the gain of the modulator is controlled from -9.5 dB to 8.5 dB, and the performance of the modulator is maintained up to 5 nsRMS external clock jitter.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.10 no.2
• /
• pp.23-35
• /
• 1973

To deal with electronic circuits analysis, the matrix-topological formulation is described. In addition to the classical mesh, node and outset method, a mixed analysis is described, and it is presented that any electronic circuits problem, including dc, ac, transient anatysis, can be analysed by the electronic circuit analysis program. In this paper a model of two stage transistor audio amplifier is made and frequency characteristics for the cicuits are analysed by ECAP. The measured results give good agreement with the ECAP analysis.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.2 no.1
• /
• pp.35-42
• /
• 1977

An analysis has been made about the performance of the switching-mode amplifier which can improve its efficiency higher than class C in audio amplification, and the improvement of characteristics and constitution in using it for modulator circuits was considered. As a result, the linearity of modulation up to 97% and the frequency response keeping flat up to 7, 200Hz have been observed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.6A
• /
• pp.488-498
• /
• 2005

The DAB(Digital Audio Broadcasting) service which is based on the Eureka-147 of Europe is developed to DMB(Digital Multimedia Broadcasting) service that is divided into Terrestrial DMB and Satellite DMB. The Satellite DMB is a new broadcasting service, which will service multi-channel multimedia broadcasting by the portable receiver or the vehicle receiver. In this paper, we consider that link level performance of satellite DMB system A which is based on the COFDM(Coded Orthogonal Division Multiplexing). It uses the OFDM method which is sensitive to nonlinearity, so we analyze the effect of the HPA(High Power Amplifier) nonlinearity. And then we define the appropriate back-off value by performing the link level simulation considering back-off effect. Also we consider the effect of frequency and time offset, and then confirm the overall link level performance by analyzing and verifying a suitable synchronization method for satellite DMB system A.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.8A
• /
• pp.1169-1178
• /
• 1999

In this paper, the method to improve audio noise when GMS(Global System of Mobile Communication) is built in HPC(Handheld PC)is provided. The biggest problem with quality of audio is improved by connecting GSM module with wire to the widest erea near by HPC Power Ground to reduce impedance difference, and designing amplifier and earpiece, Result of measurement is satisfied with GSM Acoustic Standard. Standard of GSM Audio is declared in GSM 11.10 ETS 300 607-1. Measuring items corresponds to that standard and B&K Type 6712 is used for measurement. The list of measurement presented in this paper is Sending Sensitivity Frequency Response and SLR, Sending Loudness Rating( SLR level), Receiving Sensitivity Loudness Rating(RLR level), Talker Sidetone(STMR), Stability margin, and Echo Loss(ERL)

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.2
• /
• pp.253-258
• /
• 2012

A computationally efficient interpolation filter with a low-distortion performance is a key component to utilize the naturally-sampled pulse width modulation (NPWM) in a digital domain. To realize the efficient interpolation filter, we propose a novel design based on the recently-proposed modified Farrow filter. The proposed filter shows a better pass-band distortion performance maintaining similar degree of complexity compared with the conventional Lagrange interpolation filter. We achieve the maximum distortion deviation of 10-3 dB to 20-kHz audible frequency range and distortion reduction of 1/6 times compared with the Lagrange interpolation filter.

• Economic and Environmental Geology
• /
• v.21 no.2
• /
• pp.185-191
• /
• 1988

A two channel seismic recorder suitable for long-term observation of microearthquakes is developed. The direct analogue recording on cassette tape is adopted in the recorder whose circuits of amplifier and mortor units of an audio cassette recorder are modified. The recorder provides contineous record of 10 days with DC 12V battery (100AH) and with standard cassette tape of 60 minute use. The binary coded time signals of date, hour, and minute are generated once a minute by the timing system and absolute time input using radio to measure the time drift is also possible. For the seismic signal processing, the analogue signals from audio cassette player pass A/D converter and digitized data are stored in personal computer. Then visual records can be obtained using computer graphic mode. Basic programs "ADCONVO" and "DRAWO" to accomplish A/D conversions, the creation of data files and visualization of signals were written. Some sample signals reproduced from the recorded tape are presented.