• Journal of the Korean Ceramic Society
• /
• v.37 no.3
• /
• pp.211-218
• /
• 2000

The attrition-milled powder mixtures of Al and Al2O3 were oxidized below 140$0^{\circ}C$ for 1 hr and post-sintered at 150$0^{\circ}C$ and 1$600^{\circ}C$ for 2 hr. During attrition milling, ZrO2 was added to the system by grinding effect of ZrO2 balls. The average particle size of the powder mixtures was decreased by the attrition milling as the aluminum content decrease. Above 120$0^{\circ}C$, sintering behaviro was observed on the fine Al2O3 particles resulted from the oxidation of Al. The specimens heat-treated at 140$0^{\circ}C$ for 1 hr showed the bending strength of 166 MPa and hardness of 220 MPa. The specimens post-sintered at 1$600^{\circ}C$ for 2hr had a linear shrinkage of 9~12% and a relative density of about 95%. After the post-sintering, the specimens having 55 vol% Al content revealed the bending strength of 513 MPa and hardness of 718 MPa. The Weibull modulus to the bending strength was about 16.

• Journal of the Korean Ceramic Society
• /
• v.31 no.4
• /
• pp.448-456
• /
• 1994

The reaction-sintered alumina and zirconia-alumina ceramics were fabricated from the Al/Al2O3 or Zl/ZrO2(Ca-PSZ) powder mixtures via the attrition milling. And the effects of the milling characteristics of used raw powders on reaction sintering were investigated. After attrition milling and isopressing at 400 MPa the Al/Al2O3 specimen was oxidated at 1200℃ for 8 hours followed by sintering at 1550℃ for 3 hours. Because mixed powders of flake-type Al with coarse alumina was much more effectively comminuted than the globular-type Al with coarse alumina powders, it's sintered body of more than 97% theoretical density was achived, but low contents of Al leads to relatively higher shrinkage of about 8%. And because coarse alumina particles was much more beneficial in cutting and reducing the ductile Al particles, using the coarse alumina powder was much more effective in reaction sintering. Fused Ca-PSZ powder was reaction sintered with Al at 1550℃ for 3 hours and low shrinkage ZrO2-Al2O3 composites were fabricated. But because Al/Ca-PSZ powder mixtures were not effectively milled the reaction sintering and densification was difficult. And the Ca ion in Ca-PSZ grains diffused into alumina grains during sintering so that the unstabilization of Ca-PSZ body was occured which gave the microcracks in the specimens.

• Journal of Distribution Science
• /
• v.12 no.1
• /
• pp.29-33
• /
• 2014

Purpose - The focal point of this research is to study the implications of retention, various reasons for attrition and also different ways to control attrition along with the employee retention strategies implementing by the Indian IT sector. Research design, data and methodology - After thorough literature review on employee attrition and retention, questionnaire has prepared to collect the opinions of 200 employees which were chosen from 20 IT companies (10 each from large and medium size companies) with simple random sampling technique and also gathered the opinion of these companies HR managers on strategies they are implementing to retain their talent pool through personal and telephonic interviews. Results -The research completely limited to the IT companies located in the city of Pune which is emerged as a new IT hub of India. The collected data was analyzed with Microsoft Excel and frequency distribution. Conclusions - The researchers identified job associated, compensation related and inter-personal relations for quitting their positions along with the outlook of Indian IT companies related to the identification and implementation of retention strategies like incessant hikes in compensation package, improved working conditions, continuous introduction of employee welfare facilities, and genuine promotional policy, recognition and rewards, career planning and development, and exemplary leadership.

• Journal of Technologic Dentistry
• /
• v.23 no.1
• /
• pp.9-19
• /
• 2001

Microstructure and phase transformation of Ti-Ni-Cu alloy powders produced by using attrition milling method were studied. Mixed powders of Ti-(50-X)Ni-XCu ($X=0{\sim}20$ at%) in composition range were mechanically alloyed for maximum 20 hours by using SUS 1/4" ball in argon atmosphere. Ball to powder ratio was 50: 1 and impeller speed was 350rpm. Mechanically alloyed with attrition millimg method. powder was heat treated at the temperature up to $850^{\circ}C$ for 1 hour in the $10^{-6}$ torr vacuum. Ti-Ni-Cu alloy powders have been fabricated by attrition milling method. and then phase transformation behaviours and microstructual properties of the alloy powders were investigated to assist in improving the the high damping capacity of Ti-Ni-Cu shape memory alloy powders. The results obtained are as follows: 1. After heat treating of fully mechanically alloyed powder at $850^{\circ}C$ for 1hour. most of the B2 and B 19' phases was formed and $TiNi_3$ were coexisted. 2. The B 19' martensite were formed in Ti-Ni-Cu alloy powders whose Cu-content is less than 5a/o. where as the B19 martensite in those whose Cu-content is more than 10at%. 3. The powders of as-milled Ti-Ni-Cu alloys whose Cu-contents is less than 5at% are amorphous. whereas those of as-milled Ti-Ni-Cu alloys whose Cu-content is more than 10at% are crystalline. This means that Cu addition tends to suppress amorphization of Ti-Ni alloy powders.

• Clean Technology
• /
• v.20 no.4
• /
• pp.359-366
• /
• 2014

Attrition characteristics of PKM1-SU particles, $CO_2$ absorbents for pre-combustion $CO_2$ capture process, and FCC particles, catalytic particles for hydro cracking of crude oil, were investigated at high temperature and high pressure conditions. Particle attrition tests were executed at various kinds of temperature ($0-400^{\circ}C$) and pressure (0-20 bar) conditions in a cylinder type bubbling fluidized bed with 15.1 cm diameter, 120 cm height and 1 mm orifice-sparger tube. Attrited particles before and after tests were analyzed by BET, optical microscopy, and particle size analyzer. Effects of bed material height (solid inventory) and steam injection were also verified by using ASTM D5757-95, conventional attrition test method.

• Korean Management Science Review
• /
• v.26 no.3
• /
• pp.11-21
• /
• 2009

In this paper, we proposed some valuable analysis results of cultivation campaign marketing in A mobile telephone company. The cultivation campaign marketing is a new outbound TM campaign strategy composed of 4 steps for new subscribers. During the analyses, attrition rate of A mobile company, outbound TM rejection rate, contact rate/call success rate and additional service attrition rate after subscription are measured as an effect of cultivation campaign. The results showed that there were no statistical significance in improving retention rate between customers experienced 4 step cultivation campaign and control group. However, the cultivation campaign had a better effect on improving response rate and success of selling additional service product of mobile company compared to general selling campaign. This is because cultivation campaign group had been taking care of from subscription time. It is suggested that cultivation campaign had better confined customers more likely to buy additional service to outbound TM for the sake of financial efficiency.

• Communications for Statistical Applications and Methods
• /
• v.9 no.1
• /
• pp.271-280
• /
• 2002

Recently, many companies have applied data mining techniques to promote competitive power in the field of their business market. In this study, we address how data mining, that is a technique to enable to discover knowledge from a deluge of data, Is used in an executed project in order to support decision making of an enterprise. Also, we develope scoring model on customer attrition probability for automobile-insurance company using data mining techniques. The development of scoring model in domestic insurance is given as an example concretely.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03a
• /
• pp.6-6
• /
• 2010

In this study, microstructural and piezoelectric characteristics of PNW-PMN-PZT ceramics manufactured using attrition milling method were investigated. Sintering temperature of the ceramics was varied from $980^{\circ}C$ to $1100^{\circ}C$. At the specimen sintered at $1100^{\circ}C$, mechanical quality factor(Qm) and dielectric constant showed the maxinum values of 2,373 and 1438, respectively. At the specimen sintered at $1080^{\circ}C$, electromechanical coupling factot(kp) also showed the maxinum value of 0.524.

• Journal of the military operations research society of Korea
• /
• v.26 no.1
• /
• pp.1-14
• /
• 2000

This research studies an attrition rate considering terrain feature in a battlefield. Lanchester-type combat models for heterogeneous forces and the Weapon Effectiveness Index are used in this study. The various environments of the battlefield can be explained by the terrain feature. Attrition rates of heterogeneous model are estimated by applying the battle of Baek-Sek mountain during the Korean War. Estimated attrition rates are checked by the paired samples T-Test. Specific cases are shown in this paper as an example. If we study out the relative influence of the terrain feature upon the performance of individual weapons, these will be a possible alternative to analyze the military operations.

• Asia-Pacific Journal of Business
• /
• v.11 no.4
• /
• pp.291-301
• /
• 2020

Purpose - The purpose of this study was to investigate several household characteristics related to panel attrition, examining how they may have conditioned the panel data in the Korea Welfare Panel Study (KOWEPS). Design/methodology/approach - We studied the cause of the differences in household income between the original panel and the new panel in KOWEPS. Findings - To summarize our findings, whereas it is highly likely that a low-income household or a household without health insurance will remain in the panel, it is highly likely that a high-income household or a household of more than three members will be taken off the panel. Research implications or Originality - The proportion of low-income household tends to decrease over the years, which appears to result from an overall increase in household income. Such changes are reflected in the pattern in which older panels have higher estimates of household income than newer panels.