• Journal of Environmental Science International
• /
• v.6 no.6
• /
• pp.689-696
• /
• 1997

This paper discussed effect of the surface roughness and the hydrophobicity of support material on the microbial attachment In a rotating biological contactor. The by- drophoblclty of each support material was determined by the measurement of contact angle of water and the surface roughness was measured by the surface roughness In- strument. Microorganisms have well attached on the surface of more hydrophilic support material like Nylon6 than that of the hydrophobic support material like PE. When the relatively hydrophilic surface was roughen, the microbial attachment was increased but when the relatively hydrophobic surface was roughen, the attachment was slightly In- creased because the hydrophobicity of support material was Increased by roughening the hydrophobic surface. Although both variables, the surface hydrophobicity and the surface roughness, have Influenced the microbial attachment, the influence of the surface roughness overruled that of the surface hydrophobicity. Support material whose surfaces were roughened about 1mm, 6mm and 11mm were allowed for attached 3, 7 and 24hr, but the differences of maximum and minimum attachment of each material gave nearly constant values and similar trend with time.

• Fashion & Textile Research Journal
• /
• v.11 no.1
• /
• pp.121-129
• /
• 2009

Nowadays, global interest is being placed on research and development of smart clothing which is expected to create a high added-value industry in the future. The purpose of this research is to develop smart pants with vibrating massage functions that have excellent outer appearances and provide comfort to wearers and assess outer appearance, comfort, and massaging effects of smart pants. As the results of this research, smart pants where vibrating devices which are mainly composed of vibrating motor, controller, and switch are attached were completed. Vibrating motors were fixed on a thin and light non-woven fabric material, covered with a mesh material, and attached by snaps to the experiment pants. Switch was attached to the inside of a pocket, and batteries were positioned inside of pockets. Ten subjects marked their satisfaction of wearing smart pants on a 5-point scale. Noticeable changes in outer appearance when vibrating motors operate turned out to be low. Wearer's comfort in back waist and front thigh parts where vibrating motors were attached turned out to be high-satisfied. Massaging effects of smart pants turned out to be high. Attaching and detaching vibrating devices turned out to be convenient. Lining materials used for smart paints were effective in blocking electromagnetic waves generated from vibrating devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.433-436
• /
• 2004

In this paper, we studied on the electrical safety evaluations of transformer insulation cover. In order to take preventive measures against an electric shock disaster in 22.9kV transformer installation, we put the insulation cover on a transformer charging parts. It needs to be designed so that the insulation covers have superior properties such as, arc-resistance, weather-resistance and heat-resistance, because they are used until the damage and destruction occur. To establish the protection cover to reduce the electrical shock, we analyzed damage mechanism and risk factors which happened by structural fault of an insulation cover in this paper. Also, based on the experimental results, we are planing to suggest new improved insulation cover models.

• Journal of the Korean Society of Costume
• /
• v.65 no.3
• /
• pp.76-90
• /
• 2015

This is a basic study of the two remaining armors (artifacts number K2366, K2368) from the late Joseon dynasty that is part of the Korean costume collection, which is preserved in the Mission Museum of Saint Ottilien in Germany. The armor No. 1 (artifacts number K2366) is a coat-styled armor with brass studs. It has a U-shaped neckline with the non-overlapping collars and sleeve straight-lined inseam. The armor No. 1 has the Mu to the sides and is not back slit. Both its inner and outer material are padded with cotton. Leather mails are attached on the inner lining, and studs are attached on the outer lining to match the leather mails. For this reason, the armor No. 1 can be named MyeonPiGab (brass studded armor consisting of a cotton coat with internal leather mails). The outer material is faded to have the natural white, or antique white look and the patterns on it are indigo blue. The inner material is blue, but the original color is unknown since it is faded. The lotus blossoms and vine patterns are dyed on the surface of the outer material and a name is written on the inner material. The armor No. 1 was worn between the late 17th century and the 19th century. It is estimated that it was worn by military officers who were above the mid-rank in the end of the Joseon dynasty. The armor No. 2 (artifacts number K2368) is a coat-styled armor with brass studs and a low-cut U-shaped neckline. The armor No. 2 has a slit on the left armpit and a string around it. Studs are evenly attached on the armor. The iron mails are attached to the left chest area on its inner lining. It seems that it was designed with both formality and functionality in mind. The outer material is red flannel, the inner material is blue satin and the pads are cheesecloth. The side of its collars, cuffs, front lines, sidelines, back slit, and bottom lines are trimmed with fur. There are armors called "JeonCheolGap (brass studded armor consisting of a felt coat with internal iron mails)," which is similar to the armor No. 2, however, the similarities are limited because they are not made of the same material nor do they follow the same principle of nomenclature.

• Korean Journal of Heritage: History & Science
• /
• v.54 no.4
• /
• pp.78-89
• /
• 2021

Organic residues analysis is an analysis method that reveals the types of organic material samples by using the characteristic that main components constituting substances are different depending on the species of animals and plants. In this study, scientific analysis of the organic residues attached to wood coffins in the Joseon Dynasty Hoemyo excavated from the site of Singok-dong, Uijeongbu was used to identify the types of remnants and to use them as information to restore the uses of organic materials and the way they lived in the past. As a result of FT-IR analysis of the residue attached to the inside of the wood, it was estimated to be a natural plant resin material. In addition, as a result of analysis by GC-MS to confirm the characteristic factors of natural resins, diterpenoids (abietane) and pimaran (pimarane), such as dehydroabietic acid and pimaric acid (diterpenoid) compounds, and saturated and unsaturated fatty acid components were detected together. Diterpenoid compounds are components mainly found in Pinaceae resins. It is confirmed in the literature that rosin, a representative material of Pinaceae resin, was used as an adhesive material. Considering the situation where an organic material remained at the joint of the wood, the organic material attached to the wood is judged to be an adhesive material made of Pinaceae resin. In addition, the fatty acid component detected together is a component derived from plant oil, and it is presumed to be made by mixing rosin and oil as recorded in previous studies. This study confirms that organic residues remain in the burial environment without losing their characteristics. It is expected that scientific analysis of organic residues will be conducted in the future to accumulate information necessary for the interpretation of past living culture.

• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.1
• /
• pp.61-67
• /
• 2005

The objective of this study was to investigate community structure of attached algae and microbes in sedimentation basin of water and wastewater treatment plants by using respiratory quinone profile. There was an evident difference, in microbial community structure and attached algae species, between inclination plate settler and drainage canal in the sedimentation basin. The algae was composed of species in following order; Chlorophyceae>Bascillariophyceae>Cyanophyceae. The dominant quinone types of attached microorganisms in the wastewater treatment plant were plastoquinone (PQ)-9, vitamin(V)K-1 followed by UQ-8, but those for water treatment plant were VK-1, PQ-9 followed by UQ-8. These results suggests that nutrients, seasons and material of sedimentation basin have notable influence on composition of attached algae and microbial community structure in water and wastewater treatment plants.

• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.2
• /
• pp.193-199
• /
• 2005

The objective of this study was to investigate the characteristics of adhesion and detachment of algae on various materials of drainage canal in the sedimentation basin. The influence of surface washability, surface roughness, phosphorous concentration was studied using stainless steel, cement block and ceramic panel. The algae attached content of cement block was higher than that of the ceramic coating panel. The attachment varied significantly with respect to exposure time and different materials. the attachment was higher on rough surface (cement block) when compared to smooth surfaces. The content of attached algae increased with increasing phosphorous concentration in water. The detachment efficient of algae was higher on ceramic panel.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6D
• /
• pp.753-760
• /
• 2009

This study analyzed the fluctuation of the construction material cost from 2001 to 2008 in Busan to examine the effect of the fluctuation of the construction material cost on lotting price of the multi family attached house. The major findings are as follow. First, as the result of the analysis on four materials such as reinforced bar, remicon, PHC piles, Copper Tubes, those take largest portion of construction cost, it was found that the there is wide difference in price fluctuation of the each materials. The reinforced bar and Copper Tubes showed high price increase by an average 14.03% and 14.91% per year while remicon, PHC piles remained almost unmoved by an average 0.86% and 2.41%. Second, According to the result of the analysis on the mutuality between the fluctuation of the construction material cost and the lotting price of the multi-family attached house, it was found that the fluctuation of the construction material cost have the most enormous effect on the sale price of the multi-family attached house, when there is 3 month time lag in reinforced bar, remicon, PHC piles, Copper Tubes, commonly. Also this mutuality continues to 6 month, 9 month and 1 year, although it decrease a little bit.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.834-839
• /
• 2004

In this paper, we have studied on the active vibration control of an automotive roof in passenger car's structure using piezoelectric material as the actuator and sensor attached on the surface of the automotive roof, As a control algorithm, negative velocity feedback control method is used in the study and the position of the sensor is almost attached on the nearest position of maximum normal stresses occurring while the roof is vibrating due to disturbance or exciting, Also, the actuator is attached on the other side mostly collocated to the sensor. The optimum positions have the maximum stresses of the roof which have been found in the result of the finite element analysis using Nastran software, As the fundamental experiments, a beam and plate have also been implemented to verify the performance of vibration suppression. Finally the experiment of the roof has been carried out and The roof experiment has just given a possibility to an active vibration control of the automotive structure still not applied for passenger cars.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.6
• /
• pp.42-49
• /
• 1994

One of the parameters that influence the productivity of every industry, involved in metal cutting, is the chip from ; continuous or broken chip. Chip form varies according to machining conditions, material used, tool geometry and chip breaker geometry. Therefore, in this study we carried out the experiment on the chip control in machining STS304 using an attached obstruction type chip breaker. Namely, with the change of a chip breaker distance, chip breaker angle, cutting characteristics in machining STS304 which is well-known as a machining difficult material and produces a saw-toothed chip. The results of the experiment are as follows : 1. The chip breaker distance and angle under which the preferred chip is produced, show 1.5mm and 60 .deg. , while chip breaker angle in machining an ordinary steel was well-known 45 .deg. . 2. During the cutting process, the change of feed than the change of velocity was applied as cutting conditions, effects more clearly on the chip breaking. 3. Considering a whole surface roughness, it is not advisable to apply chip breaker mentioned above for precision cutting.