• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.444-445
• /
• 2006

Flying trajectories of fine particles within a size range of $10{\sim}60{\mu}m$ were studied during centrifugal atomizing processes. A FORTRAN program was written by using increment method. Calculation results revealed that the drag force might reach very high value of 522-7800 g for fine powder of $10{\sim}60{\mu}m$. Flying distance in horizontal direction could be shortened if the particles fly obliquely due to the huge drug force. On the other hand, very fine powder could be projected to far distances when the atmosphere flow velocity is much stronger. Fortunately such particles could be contracted within a cylinder closed to the atomizer when the atmosphere flow was weaken or retained in a limited diameter.

• 한국주조공학회지
• /
• 제17권5호
• /
• pp.480-487
• /
• 1997

Particle reinforced metal matrix composites(MMCs) via a centrifugal spray-cast deposition(CSD) process were fabricated by injecting second phase particles($Al_2O_3$<40${\mu}m$, W<17.3${\mu}m$) into copper melt on the atomizing disc. Compositing modes were investigated by combining microstructures and mathematical modeling between Cu droplets and the reinforced particles injected. The $Cu/W_P$ powders were shown that the W particles penetrate and get embedded in the Cu droplets. It is considered that the W particles composite preferentially in Cu melt on the atomizing disc. On the other hand, the $Al_2O_3$, particles did not penetrate into the Cu droplets on the atomizing disc but get attached in surface of Cu droplets during the flight. It is considered that the compositing may be attained in the flight distance which the relative velocity between Cu droplet and $Al_2O_3$, particle is maximum. The microstructure of the $Cu/W_P$ and the $Cu/(Al_2O_3)_p$ composite preform was strongly influenced by compositing modes of droplets, and after subsequent deposition it was comprised as it is called the dispersed type and the cell type of microstructure, respectively.

• 대한기계학회논문집
• /
• 제14권5호
• /
• pp.1211-1221
• /
• 1990

본 연구에서는 CWM을 이류체 미립화기(twin-fluid atomizer)로 미립화 시켜 미립화에 크게 영향을 미치는 인자들로 믿어지는 공기분사압력, 부하도(loading), 미 분탄의 크기 그리고 CWM 방울 채집위치의 변화가 CWM 방울크기 분포와 CWM 방울안 미 분탄 존재유무에 미치는 영향을 연구의 목적으로 하였다.

• 대한기계학회논문집
• /
• 제15권2호
• /
• pp.618-629
• /
• 1991

The purpose of this experiment is to understand the distribution of coal particles inside CWM droplet which is believed to be a very important factor controlling the flame stability. CWM slurry is atomized by an air assisted twin fluid nozzle. An experimental rig is designed and fabricated. The mean size of coal particle distribution in CWM slurry, atomizing air pressure, coal particle loading in slurry and sampling position inside spray are main experimental variables. The atomized CWM droplets are sampled on the thin white layer of magnesium oxide by the emergency sampling shutter. The sampled coal particles on magnesium oxide layers are collected into test tubes and dispersed completely by Ultra-Sonicator. The size distribution of coal particles inside droplets are measured by Coulter Counter. The presence of coal particle inside the impressions of droplets on magnesium oxide layer are investigated by photo technique. There are quite many droplets which do not have any coal particles. Those are just water droplets, not CWM droplets. The population ratio of droplets without coal particles to toal number of droplets is strongly affected by the mean size of coal particle distribution in slurry and this ration becomes bigger number as the mean size of coal particles be larger. The size distribution of coal particles inside CWM droplets is not even and depends on the size of droplet. Experimental results show that the larger CWM droplets has droplets has bigger mean value of particle size distribution. This trend becomes more evident as the atomizing air pressure is raised and the mean size of coal particles in CWM slurry is bigger. That is, the distribution of coal particles inside CWM dropolets is very much affected by the atomizing air pressure and the mean size of pulverized coal particles in CWM slurry.

• Journal of Welding and Joining
• /
• 제5권2호
• /
• pp.17-26
• /
• 1987

In this study, the experiments were carried out for the purpose of establishment of the arc sparing method which reducing oxides or oxide film by using the inert gas as the carrier gas of atomizing particles. Main results obtained are as follows; 1. Oxides and oxide film which lower the adhesion strength are largely reduced by using the inert gas as the carrier gas of atomizing particles, and adhesion strength of coating film are improved. 2. The coating film characteristics appear to be no difference between the inert gas arc spraying in air environment and that in argon gas environment. 3. Inert gas arc spraying using argon as the carrie gas has higher reduction rate of composition element in coating film than compressed air spraying does.

• 한국기계가공학회지
• /
• 제9권3호
• /
• pp.42-48
• /
• 2010

The aim of this study is to investigate the influence of driving atomizing nozzle position, the slope of sludge entering tube and supplying air flow rate on the performance of sludge air dryer. This paper deals with optimization of the geometry of the atomizing nozzle for sludge drying using computational fluid dynamics and drying performance test using pilot air dryer. The air drying system was composed of the atomizing nozzle which made high-speed fluid field. dewatered cake was crushed at the high-speed zone as the first step and formed intto dried powder of sphere shape by the collision between particles at the circling zone. The CFD analysis results show when the slope of entering sludge tube is smaller, suction air amount is increased. It is shown that the developed atomizing nozzle is very excellent in the drying performance through pilot test.

• 오토저널
• /
• 제14권5호
• /
• pp.41-53
• /
• 1992

The main purpose of this study is to investigate the atomizing characteristics of a two phase spray by using a liquid column type coaxial nozzle. The experiments have been carried out to analyze the atomization behavior, the droplet size distributions, and the statistical properties of droplet size distributions. Immersion sampling method and the image processing technique were adapted for the measurements of particles, and the distributions of the droplet sizes were statistically analyzed. In the experiments, the mass ratio defined as Mr= $M_{\sigma}$/ $M_{1}$ has been changed from 1.0 to 3.4 and the measurements have been performed along the axis of the spray. As a result of this experimental study, the distributions of droplet size were satisfied with the Log-Normal distributions and arithmetic mean diameter and deviation of mass ratio. Droplet volume-surface mean diameter was denoted by a exponential function of mass-ratio and the exponent was denoted by linear relation according to the central axis from the nozzle. Dispersions, skewness factors and flatness factors had comparatively constant values regardless of mass ratio and location.

• 한국전기전자재료학회논문지
• /
• 제22권5호
• /
• pp.405-410
• /
• 2009

The conventional ultrasonic nozzle produces a mist by applying an ultrasonic vibration into a non-flowering liquid. In this paper, we first present a novel designed nozzle type sprayer that is able to apply an ultrasonic vibration directly to the moving liquid and generate a mist instantly. For the novel nozzle, a ring-type actuator of the novel nozzle was designed and built using the PZW-PMN-PZT ceramics. This paper will describe a variety of physical, mechanical, and electrical characteristics of the ultrasonic nozzle. The characteristics of the mist particles was also measured as the amount of the outflow liquid was varied.

• 한국재료학회지
• /
• 제24권11호
• /
• pp.591-598
• /
• 2014

In this research, magnesium powder was prepared by gas atomizing. Refinement behaviors of magnesium powder produced under different conditions were investigated using a mechanical milling (attrition milling) process. Analyses were performed to assess the characterization and comparison of milled powder with different steel ball sizes and milling times. The powders were analyzed by field emission scanning electron microscope, apparent density and powder fluidity. The particle morphology of the Mg powders changed from spherical particles of feed metals to irregular oval particles, then plate type particles, with an increasing milling time. Because of the HCP structure, deformation occurs due to the existence of the easily breakable C-axis perpendicular to the base, which results in producing plate-type powders. An increase in ball size and the impact energy of the magnesium powder maximizes the effect of refinement. Furthermore, it is possible to improve the apparent density and fluidity according to the smoothness of the surface of the initial powder.

• 한국산학기술학회논문지
• /
• 제13권9호
• /
• pp.4334-4340
• /
• 2012

본 연구에서는 미세 액적을 발생시키는 액적 발생 장치를 개발 제작하고 이에 대한 성능 평가를 실시하였다. 액적 발생 장치는 spray-evaporation method를 기초로 제작하였으며, 0.3mm, 0.5mm의 오리피스를 사용하였다. 압축 공기 공급 압력을 1bar에서 4bar로 증가시키면서 공급 압력에 따른 발생되는 액적 크기의 미세 정도를 비교하였다. 또한 SMPS(Scanning Mobility Particle Sizer)와 OPC(Optical Particle Counter)를 이용하여 서로 다른 오리피스를 장착한 액적 발생 장치에서 발생되는 액적의 크기 분포를 측정하였다. 연구 결과, 0.3mm 오리피스를 장착한 장치에서 발생되는 액적은 $0.3{\mu}m$ 인근의 크기가 가장 많았으며, 미립화되는 입자는 매우 안정적이었다. 또한 0.5mm 오리피스를 장착한 장치가 0.3mm 오리피스를 장착한 장치에 비해 발생되는 액적의 크기가 큰 것으로 나타났다. 이러한 액적 발생 장치는 입자의 미세한 응집 현상이 나타나는데, 이것은 내부 액체가 미세한 액적으로 미립화되어 분사되기 때문인 것으로 사료된다. 본 연구에서 제작한 액적 발생 장치는 미세 입자를 미립화하기 위한 에어로졸 발생 장치로 사용 가능한 것으로 판단된다.