• 한국분무공학회지
• /
• 제28권2호
• /
• pp.89-96
• /
• 2023

This study presents a numerical simulation investigating hydrodynamic characteristics of high-temperature hydrocarbon aviation fuel injected through a plain orifice injector. The analysis encompassed the temperature range up to the critical point, and the obtained results were compared with prior experimental observations. The analysis unveiled that the injector's exit pressure remains equivalent to the ambient pressure when the fuel injection temperature is below the boiling point. However, when the fuel temperature surpasses the boiling point, the exit pressure of the injector transitions to the saturated vapor pressure corresponding to the fuel injection temperature. Consequently, the exit pressure of the injector increases in tandem with the rapid increase of the saturation vapor pressure due to escalating fuel temperatures. This rise in the exit pressure necessitates a proportional increase in fuel injection pressure to ensure a fixed fuel mass flow rate. Furthermore, the investigation revealed that the discharge coefficient obtained by applying the exit pressure instead of the ambient pressure did exhibit no decrease, but rather was maintained at a nearly constant value, comparable to its level below the boiling point.

• 한국분무공학회지
• /
• 제28권4호
• /
• pp.169-175
• /
• 2023

Multi-injection scheme is being applied to GDI combustion to reduce PM and PN emission to meet the EU7 regulation. However, very short injection duration encounters the ballistic injection region, which injection quantity does not increase linearly with injection duration when applying multi-injection. In this study, numerical studies were conducted to reveal the cause of ballistic injection and the effect of design parameters on ballistic region using 1-D simulation, AMESim. Injection rate and injection quantity were compared with experiment to validate the established model, which showed the accuracy with 10% error. The model revealed that the tendency of ballistic region coincides with the needle motion behavior, which means that parameters at the upper part of needle such as electro-magnetic force, needle spring force and needle friction force have dominant effect on ballistic injection. To figure out the effect of electro-magnetic and needle friction force on ballistic, those parameters were varied to plus and minus 10% with model. The result showed that those parameters clearly changed the ballistic region characteristics, however, the impact became insignificant for outside of ballistic region, which means that the ballistic injection is mainly influenced by initial motion of injector needle.

• 한국항공우주학회지
• /
• 제34권9호
• /
• pp.67-75
• /
• 2006

스월 인젝터의 비선형 동적특성을 모사할 수 있는 수치해석 모델을 개발하여 인젝터내의 정적/동적 특성을 분석하였다. Boundary Element Methods (BEMs)을 적용한 수치모델은 유체 경계면 산출에 매우 유리한 장점이 있어 표면의 불안정성 해석에 유용하게 적용되어 왔다. 이전의 연구 결과에서는 스월효과를 고려할 수 있도록 확장된 수치모델을 이용하여 인젝터의 형상을 고려한 정적특성을 보여주었다. 본 논문에서는 유입 흐름에 교란이 발생했을 때 인젝터의 각 구성요소에서의 동적응답을 분석하였고, 이론적 결과와 비교하여 수치모델에 대한 타당성을 검증하였다. 본 수치해석 결과는 입력류에서의 교란이 각 인젝터 구성품을 지나면서 감쇠/증폭되고 위상차를 만들게 되는 과정을 잘 모사하고 있다. 개발된 수치모델은 인젝터의 다양한 설계변수들이 유동특성에 미치는 효과 분석과 이론적 모델로는 예측이 어려운 비선형 영역에서의 동적 응답특성 분석에 유용하게 적용될 수 있을 것이다.

• 한국수소및신에너지학회논문집
• /
• 제25권6호
• /
• pp.636-642
• /
• 2014

As environment problem became a worldwide issue, countries are tightening regulations regarding greenhouse gas reduction and improvement of air pollution problems. With these circumstances, one of the renewable energies produced from biomass is getting attention. Bio-ethanol, which is applicable to SI engine, showed a positive effect on the PFI (Port Fuel Injection) type. However, Ethanol has a problem in homogeneous mixture formation because it has high latent heat of vaporization characteristics and in the GDI (Gasoline Direct Injection) type, mixture formation is required quickly after fuel injection. Particularly, South Korea is one of the countries with great temperature variation among seasons. With this reason, South Korea supply fuel additive for smooth engine operation during winter. Therefore, experimental study and investigation about application possibility of blending fuel is necessary. This paper demonstrates the spray characteristics by using the CVC direct injection and setting the bio-ethanol blending fuel temperature close to the temperature during each seasons: -7, 25, $35^{\circ}C$. The diameter and the width of the CVC are 86mm and 39mm. High-pressure fuel supply system was used for target injection pressure. High-speed camera was used for spray visualization. The experiment was conducted by setting the injection pressure and ambient pressure according to each temperature of bio-ethanol blending fuel as a parameter. The result of spray visualization experiment demonstrates that as the temperature of the fuel is lower, the atomization quality is lower, and this increase spray penetration and make mixture formation difficult. Injection strategy according to fuel temperature and bio-ethanol blending rate is needed for improving characteristics.

• 대한기계학회논문집B
• /
• 제35권1호
• /
• pp.67-73
• /
• 2011

본 연구는 DME-바이오디젤 혼합연료의 분무 및 연소, 배기 특성을 바이오디젤과 비교한 실험적 연구이며 실험연료는 바이오디젤 (BD100)과 중량 기준으로 DME를 20% 혼합한 DME-바이오디젤 혼합연료 (B-DME20)이다. 거시적 분무 특성을 연구하기 위하여 분무 이미지로부터 분무도달거리, 분무각을 측정하였으며, 연소 및 배기 특성은 단기통 직접 분사식 압축착화 기관을 이용하여 분석하였다. 실험결과 바이오디젤과 DME-바이오디젤 혼합연료는 분사율에서는 큰 차이가 없었지만 혼합연료의 경우에 착화지연기간이 짧고 연소압력이 높았으며soot 배출물이 현저하게 줄어들었다.

• 한국분무공학회지
• /
• 제6권1호
• /
• pp.18-24
• /
• 2001

Liquid fossil fuel contaminated by water can cause trouble in the combustion processes and affect the endurance of a combustion system. Using an optical sensor to monitor the water content instantaneously in a fuel pipeline is an effective means of controlling the fuel quality in a combustion system. In two component liquid flows of oil and water, the flow pattern and characteristics of water droplets are changed with various flow conditions. Additionally, the light scattering of the optical sensor measuring the water content is also dependent on the flow patterns and droplet characteristics. Therefore, it is important to investigate the detailed behavior of water droplets in the pipeline of the fuel transportation system. In this study, the flow patterns and characteristics of water droplets in the turbulent pipe flow of two component liquids of gasoline and water were investigated using optical measurements. The dispersion of water droplets in the gasoline flow was visualized, and the size and velocity distributions of water droplets were simultaneously measured by the phase Doppler technique. The Reynolds number of the gasoline pipe flow varied in the range of $4{\times}10^{4}\;to\;1{\times}10^{3}$, and the water content varied in the range of 50 ppm to 300 ppm. The water droplets were spherical and dispersed homogeneously in all variables of this experiment. The velocity of water droplets was not dependent on the droplet size and the mean velocity of droplets was equal to that of the gasoline flow. The mean diameter of water droplets decreased and the number density increased with the Reynolds number of the gasoline flow.

• 한국분무공학회지
• /
• 제19권1호
• /
• pp.1-8
• /
• 2014

Liquefied petroleum gas (LPG) is regarded as an alternative fuel for spark ignition engine due to similar or even higher octane number. In addition, LPG has better fuel characteristics including high vaporization characteristic and low carbon/hydrogen ratio leading to a reduction in carbon dioxide emission. Recently, development of LPG direct injection system started to improve performance of vehicles fuelled with LPG. However, spray characteristics of LPG were not well understood, which is should be known to develop injector for LPG direct injection engines. In this study, effects of operation condition including ambient pressure, temperature, and injection pressure on spray properties of n-butane were evaluated and compared to gasoline in a multi-hole injector. As general characteristics of both fuels, spray penetration becomes smaller with an increase of ambient pressure as well as a reduction in the injection pressure. However, it is found that evaporation of n-butane was faster compared to gasoline under all experimental condition. As a result, spray penetration of n-butane was shorter than that of gasoline. This result was due to higher vapor pressure and lower boiling point of n-butane. On the other hand, spray angle of both fuels do not vary much except under high ambient temperature conditions. Furthermore, spray shape of n-butane spray becomes completely different from that of gasoline at high ambient temperature conditions due to flash boiling of n-butane.

• 한국분무공학회지
• /
• 제19권3호
• /
• pp.115-122
• /
• 2014

As a demand for an automobile increases, air pollution and a problem of the energy resources come to the fore in the world. Consequently, governments of every country established ordinances for green-house gas reduction and improvement of air pollution problem. Especially, as international oil price increases, engine using clean energy are being developed competitively with alternative transportation energy sources development policy as the center. Bio ethanol, one of the renewable energy produced from biomass, gained spotlight for transportation energy sources. Studies are in progress to improve fuel supply methods and combustion methods which are key features, one of the engine technologies. DI(Direct Injection), which can reduce fuel consumption rate by injecting fuel directly into the cylinder, is being studied for Green-house gas reduction and fuel economy enhancement at SI(Spark Ignition). GDI(Galoine Direct Injection) has an advantage to meet the regulations for fuel efficiency and $CO_2$ emissions. However it produces increased number of ultrafine particles, that yet received attention in the existing port-injection system, and NOX. As fuel is injected into the cylinder with high-pressure, a proper injection strategy is required by characteristics of a fuel. Especially, when alcohol type fuel is considered. In this study, we tried to get a base data bio-ethanol mixture in GDI, and combustion for optimization. We set fuel mixture rate and fuel injection pressure as parameters and took a picture with a high speed camera after gasoline-ethanol mixture fuel was injected into a constant volume combustion chamber. We figured out spraying characteristic according to parameters. Also, we determine combustion characteristics by measuring emissions and analyzing combustion.

• 한국분무공학회지
• /
• 제28권1호
• /
• pp.16-23
• /
• 2023

The objective of this numerical study is to investigate the effect of the shape and material of the blower blade for the electrified speed sprayer on the blowing performance. The shape of the blade was changed to the bonding angle, the number of blades, the width of the blade, and the blade length based on the existing model. In order to obtain the reliability of the numerical model, the analysis of the grid dependence was performed in the numerical analysis. The numerical analysis results were compared and analyzed in terms of the agricultural chemical penetration length characteristics, flow uniformity characteristics, and velocity distribution characteristics. Furthermore, the effect of material change on weight reduction and structural characteristics was also compared and analyzed. As a result of the analysis, it was found that the optimal condition was that the blade angle was 45°, the number of blades was 12, and the width was 115 mm, which was confirmed through a comparison of the inlet mass flow rate. As a result of the equivalent stress lower than the yield strength due to the material change from aluminum to steel compared to the existing steel, structural defects do not appear, and it is judged that the operation time compared to the battery capacity will be improved through the weight reduction of the blade.

• 한국수소및신에너지학회논문집
• /
• 제25권5호
• /
• pp.533-540
• /
• 2014

The remanufacturing industry for automotive parts is a major issue which affects the environment protection and CO2 reduction throughout the world. Beside this, remanufacturing technologies of worn-out diesel engines have been developing to make as close to new as possible. In this study, the characteristics of the engine-power output and exhaust emissions of remanufactured diesel engine by hydrogen enrichment are evaluated by measuring the engine and vehicle test. Moreover, with worn-out diesel engine and first generation common-rail engine, we compared by testing their characteristics, resulting in the restoration of engine-power output more than 93%, as well as marvelously reduces the THC and NOx emission. At a guess, high pressure injection of diesel increases fuel atomization characteristics with excellence combustion efficiency, resulting in reduction of THC emission. Also, rapid cooling of EGR decreases combustion temperature, resulting in reduction of NOx emission. Consequently, these remanufacturing for diesel engine enables worn-out diesel engine to have restoration to the original state. Simultaneously achieved 2 goals called that CO2 emission reduction and protection of environment by remanufacturing engine.