• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.6
• /
• pp.83-90
• /
• 2017

Concrete structure for nuclear power plant is mass concrete structure with large wall depth and easily permits cracking in early age due to hydration heat and drying shrinkage. It always needs cooling water so that usually located near to sea shore. The crack on concrete surface permits rapid chloride intrusion and also causes more rapid corrosion in the steel. In the study, the effect of age and crack width on chloride diffusion is evaluated for the concrete for nuclear power plant with 6000 psi strength. For the work, various crack widths with 0.0~1.4 mm are induced and accelerated diffusion test is performed for concrete with 56 days, 180days, and 365 days. With increasing crack width over 1.0mm, diffusion coefficient is enlarged to 2.7~3.1 times and significant reduction of diffusion is evaluated due to age effect. Furthermore, apparent diffusion coefficient and surface chloride content are evaluated for the concrete with various crack width exposed to atmospheric zone with salt spraying at the age of 180 days. The results are also analyzed with those from accelerated diffusion test.

• Fire Science and Engineering
• /
• v.24 no.3
• /
• pp.52-57
• /
• 2010

Fire protection countermeasure were considered on the straw thatched roof and wooden structure. For the fire resistant treatment, rice straw was soaked in the fire resistant liquid with different soaking time. After treatment, some rice straw sample was washed with water then the rice straws were tested to check the fire resistance performance. And the wood was soaked in the fire resistant liquid at an atmospheric pressure, vacuum-pressure condition and painted with brush on the surface. To analyse the fire resistant performance of rice straw, ignition delay time was measured under the radiant heat flux of cone heater. And the fire resistant performance of wood samples were tested with 45 degree fire resistant test apparatus and cone heater. Based on the cone heater test, the rice straw which most easily ignitable material shows the longer ignition delay time than not treated ones and even in the water washed straw show a longer ignition delay time than not treated ones. And fire resistant treated woods of vacuum-pressure treated sample showed the most excellent performance on fire resistance. And the fire resistant treated by brush and soaking showed a longer ignition delay time than not treated ones. From this experiment, it was found that a fire resistant treatment of rice straw and wood of the house can be protected from the fire spread.

• Journal of the Korean Geographical Society
• /
• v.33 no.3
• /
• pp.395-409
• /
• 1998

The purpose of this paper is to determine the atmospheric conditions in whih urban areas affect the precipitation processes and to evaluate whether certain weather types show more apparent urban effect on precipitation modification over five cities in the southem United States. Each heavy rainstorm is classified into one of three synoptic weather types (frontal storm, airmass storm or tropical disturbance storm). Heavy rainstorm day is defined as day producing rainfall totals that equal o exceed 2 inches (50.08 mm). Houston, Dallass and San Antonio show possible urban effects on rainfall totals and frequencies of heavy rainstorms by airmass storm type while New Orleans and Memphis do not reveal any distinct precipitation enhancements through the synoptic analysis. The results of TSA (Trend Surface Analysis) show that frontal and tropical disturbance storm types have stronger climatic gradients than airmass types and the patterns of rainfall totals have stronger trends than those of rainfall frequencies for the five cities. The results suggest that airmass type events may well reveal possible precipitation enhancements due to urban effects since they are less influenced by a strong climate gradient and they provide favorable conditions for development of urban heat islands. Residual analysis confirms that rainfall totals and frequencies of heavy rainstorms by airmass storm type have positive residuals over the city or the major effect area.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.27 no.1
• /
• pp.46-58
• /
• 2017

Objectives: Particulate matter (PM) at construction sites mostly originates from either construction activities or the atmospheric environment. This study was conducted to evaluate the exposure level to PM and the contribution ratio of atmosphere sources at construction sites. Methods: We reviewed literature and governmental systems related to PM exposure in occupational settings and summarized them. In the field evaluation, five construction sites and one golf course were selected: two from Gyeonggi-do Province and four from North Gyeongsang-do Province. For each site, personal samples from outdoor construction workers and area samples from the outdoor area around the construction site office were collected according to construction work types. PM concentrations reported from nearby National Ambient Air Monitoring Stations were recorded. Respirable dust concentrations, respirable silica concentrations, and several metal concentrations including Cd, Cr, Pb, and As were monitored over four months. In the end we suggested how to manage particulate matter exposure at construction sites. Results: There was little literature reporting on exposure levels of construction workers to PM. Respirable dust concentrations measured in Gyeonggi-do Province were higher than those measured in North Gyeongsang-do Province. The geometric means of respirable dust concentrations in personal samples and area samples were $37.89{\mu}g/m^3$ and $92.86{\mu}g/m^3$, respectively. The respirable dust concentrations were higher than the PM concentrations reported from nearby National Ambient Air Monitoring Station. The geometric means of respirable silica concentrations of personal samples and area samples were $1.3{\mu}g/m^3$ and $1.1{\mu}g/m^3$, respectively. All metal concentrations were lower than 10% of individual Korean occupational exposure limits. Conclusions: Assuming that personal samples consisted of ambient PM and dust originating from work activities and area samples only collected ambient PM, we concluded that the dust exposure of outdoor construction workers originated 40.8% from the atmosphere and 59.2% from construction activities. PM exposure at construction sites should be controlled by employers, as in the case of outdoor heat stress. The Korean government needs to consider setting an occupational exposure limit for respirable dust.

• Applied Chemistry for Engineering
• /
• v.25 no.1
• /
• pp.41-46
• /
• 2014

The property improvement of polycarbonate coated with a multilayer film composed of an inorganic $SiO_2$ film and a photocatalytic $TiO_2$ film was studied. The $SiO_2$ film as a binder had an excellent light transmission characteristic. After the treatment with atmospheric pressure plasma, the surface of $SiO_2$ film showed the hydrophilicity, which increased the film coating uniformity with a $TiO_2$-containing aqueous solution. When $TiO_2$ film was over 200 nm thick, the absorption effect of UV rays in the range of 180~400 nm suppressed the yellowing phenomena of polycarbonate substrate. The inorganic film improved the heat resistance of polycarbonate substrates. $TiO_2$ film in the outmost under the exposure of UV rays promotes the catalytic oxidation characteristics and yields the capability to the decomposition of organic contaminants, and also increases the self-cleaning properties due to the increase of hydrophilicity. Structural stability of the polycarbonate substrate coated with inorganic $TiO_2$ and $SiO_2$ film was shown. The role of $SiO_2$ film between $TiO_2$ and polycarbonate substrate suppressed the peeling of $TiO_2$ film by inhibiting the photocatalytic oxidation effect of $TiO_2$ film on the polycarbonate substrate.

• Food Engineering Progress
• /
• v.15 no.4
• /
• pp.398-403
• /
• 2011

A dielectric barrier discharge plasma (DBDP) treatment system was fabricated and the optimum operating conditions for the plasma generation were determined in order to explore the potential of cold plasma as a non-thermal proessing technology. The microbial inactivation performance of the system was also evaluated against Staphyloocus aureus. The system consisted of power supply, transformer, electrode assembly and sample treatment plate. The input power was 220 V single phase AC and amplified to 10.0-50.0 kV on a transformer. A pulsed sine wave of frequency 10.0-50.0 kHz was introduced to the electrode embedded in ceramic as a dielectric barrier material in order to generate plasma at atmospheric pressure. Higher currents and consequently greater power were required for the plasma generation as the frequencies increased. A homogeneous and stable plasma was generated at currents of 1.0-2.0, and frequencies of 32.0-35.3 kHz. The optimum electrode-gaps for the plasma generation were 1.85 mm without loaded samples. More power was consumed as the electrode-gaps increased. The practically optimum electrode- gap was, however, 2.65 mm when samples were treated on slide-glasses for microbial inactivation. The maximum temperature increase after 10 min treatment was less than 20$^{\circ}C$, indicating no microbial inactivation effect by heat and thereby insuring a non-thermal method. The DBDP inactivation effect against Staphyloocus aureus increased linearly with treatment time up to 5 min, but plateaued afterward. More than 5 log reduction was achieved by 10 min treatment at 1.25 A.

• Journal of Environmental Science International
• /
• v.28 no.3
• /
• pp.341-356
• /
• 2019

In this study, the impacts of local meteorology caused by tidal changes in the West Sea on ozone distributions in the Seoul Metropolitan Area (SMA) were analyzed using a meteorological model (WRF) and an air quality (CMAQ) model. This study was carried out during the day (1200-1800 LST) between August 3 and 9, 2016. The total area of tidal flats along with the tidal changes was calculated to be approximately $912km^2$, based on data provided by the Environmental Geographic Information Service (EGIS) and the Ministry of Oceans and Fisheries (MOF). Modeling was carried out based on three experiments, and the land cover of the tidal flats for each experiment was designed using the coastal wetlands, water bodies (i.e., high tide), and the barren or sparsely vegetated areas (i.e., low tide). The land cover parameters of the coastal wetlands used in this study were improved in the herbaceous wetland of the WRF using updated albedo, roughness length, and soil heat capacity. The results showed that the land cover variation during high tide caused a decrease in temperature (maximum $4.5^{\circ}C$) and planetary boundary layer (PBL) height (maximum 1200 m), and an increase in humidity (maximum 25%) and wind speed (maximum $1.5ms^{-1}$). These meteorological changes increased the ozone concentration (about 5.0 ppb) in the coastal areas including the tidal flats. The increase in the ozone concentration during high tide may be caused by a weak diffusion to the upper layer due to a decrease in the PBL height. The changes in the meteorological variables and ozone concentration during low tide were lesser than those occurring during high tide. This study suggests that the meteorological variations caused by tidal changes have a meaningful effect on the ozone concentration in the SMA.

• Journal of Korea Foundry Society
• /
• v.43 no.3
• /
• pp.107-136
• /
• 2023

Natural silica sand was commonly used for sand casting of cast steel products, and chromites sand was used to suppress seizure defects due to the lack of thermal properties of silica sand. However there are disadvantages such as deterioration by repeated use, system sand mixing problem, difficulty separating and removing, increased during mold according to high density and to being waste containing chrome. Recently, industrial waste reduction and atmospheric environment improvement have been highlighted as important tasks in the casting industry. In order to solve the problems that occur when using foundry Sand and to improve the environment of casting factories, various artificial sands that can be applied instead of natural silica sand have been developed and introduced. Artificial sands can be classified into artificial sand manufactured by the electric arc atomization or gas flame atomization, artificial sand manufactured by the spray drying & sintering process, artificial sand manufactured by the sintering & crushing process and exhibit different physical properties depending on the type of raw-minerals and manufacturing method. In this study, comparative evaluation tests were conducted on the physical properties of various foundry sands, mold strength, physical durability, thermal durability, and casting test pieces. When comprehensively considering the actual amount of molding sand used according to density, the mold strength according to the shape of sand, the physical and thermal durability of foundry sand, and the heat resistance characteristics of foundry sand, 'Molten artificial sand A1' or 'Molten artificial sand B' is judged to be the most suitable spherical artificial sand for casting of heavy steel castings.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.37 no.3
• /
• pp.54-60
• /
• 2009

The purpose of this study is to analyze the impacts of three-dimensional land cover on changing urban air temperatures and to explore some strategies of urban landscaping towards mitigation of heat build-up. This study located study spaces within a diameter of 300m around 24 Automatic Weather Stations(AWS) in Seoul, and collected data of diverse variables which could affect summer energy budgets and air temperatures. The study also selected reflecting study objectives 6 smaller-scale spaces with a diameter of 30m in Chuncheon, and measured summer air temperatures and three-dimensional land cover to compare their relationships with results from Seoul's AWS. Linear regression models derived from data of Seoul's AWS revealed that vegetation volume, greenspace area, building volume, building area, population density, and pavement area contributed to a statistically significant change in summer air temperatures. Of these variables, vegetation and building volume indicated the highest accountability for total variability of changes in the air temperatures. Multiple regression models derived from combinations of the significant variables also showed that both vegetation and building volume generated a model with the best fitness. Based on this multiple regression model, a 10% increase of vegetation volume decreased the air temperatures by approximately 0.14%, while a 10% increase of building volume raised them by 0.26%. Relationships between Chuncheon's summer air temperatures and land cover distribution for the smaller-scale spaces also disclosed that the air temperatures were negatively correlated to vegetation volume and greenspace area, while they were positively correlated to hardscape area. Similarly to the case of Seoul's AWS, the air temperatures for the smaller-scale spaces decreased by 0.32% ($0.08^{\circ}C$) as vegetation volume increased by 10%, based on the most appropriate linear model. Thus, urban landscaping for the reduction of summer air temperatures requires strategies to improve vegetation volume and simultaneously to decrease building volume. For Seoul's AWS, the impact of building volume on changing the air temperatures was about 2 times greater than that of vegetation volume. Wall and rooftop greening for shading and evapotranspiration is suggested to control atmospheric heating by three-dimensional building surfaces, enlarging vegetation volume through multilayered plantings on soil surfaces.

• Journal of Korean Medical classics
• /
• v.23 no.2
• /
• pp.205-223
• /
• 2010

In Korean Traditional Medicine(abbreviated to K.T.M.), hyperhidrosis and anhidrosis are the targets of the medical treatment. Furthermore sweating appearance is also one of the important symptoms which explain a particular situation of the patient in K.T.M. And at "Sanghanron(傷寒論)" which is a traditional chief clinical bible written by Jang Gi(張機) later Han dynasty(漢代) in China made full use of the various kinds of diaphoresis[汗法] as a main medical treatment with purgation therapy[下法] and emetic therapy[吐法]. So the sweat in itself not only is the disease, but also is one of the symptoms explain a disease pattern. This thesis inquires into "Hwangjenaegyeong(黃帝內經)" referring to sweat which is the origin of recognition to the sweat in K.T.M. Some theses similar to this research had been made progresses and already reported, but most of them have classified the contents into biology, pathology, diagnosis, treatment after the model of western medical theory. In the aspect of comparative studying with other literature and clinic practical using, we found characteristics of referring to sweat in "Hwangjenaegyeong(黃帝內經)". And we classify the characteristics into some categories as follows. 1. There are some terms which make a title including sweat and symbolize the characteristics, for example sweat of soul[魄汗], sweat of death[絶汗], sweat of streaming[灌汗], sweat of weakness[白汗], sweat of sleep[寢汗], sweat of bright and heat[炅汗], sweat of kidney[腎汗], sweat of escaping[漉汗], cold sweat[寒汗], sweat on the head[頭汗], hyperhidrosis[多汗], heavy sweat[大汗]. But there aren't spontaneous sweat[自汗] or sweat like a thief[盜汗] which are the normal terms referring to sweat in history of K.T.M. And there are several descriptions about sweat appearance such as sweating in half of body[汗出偏沮], sweating in the rear end and thigh and knee[汗出尻陰股膝], hyperhidrosis in the neck and aversion to wind[頸多汗惡風], hyperhidrosis in the head and face and aversion to wind[頭面多汗惡風], cannot stopping the sweating under head[頭以下汗出不可止], make a person sweat to one's feet[令汗出至足], sweating like escaping[漯漯然汗出], sweating like soaking[汗出如浴], sweating become moist[汗出溱溱], hardly escaping sweat[汗大泄], escaping sweating[漉漉之汗], sweat moisten the pores [汗濡玄府], ceaseless sweating like pouring[汗注不休] sweating like pouring and vexation[汗注煩心], damp with sweat[汗汗然], sweating spontaneously[汗且自出], removal of fever with sweat drying[熱去汗稀]. That can be divided into sweat region and sweat form. 2. There are detailed explanations of the principle of perspirations caused by hot weather, hot food, hard working and meeting damp pathogen. 3. There are some explanations of the principle of removing fever due to the excessive heat from internal and external body through sweating by replenishing the body fluid. And many descriptions about overcoming the febrile disease by dropping temperature through sweating and many diaphoresis for curing. 4. There are some descriptions about five Jang organs perspirations and attachment of five mucous body fluid to five Jang organs. 5. There are pathogenic progresses after sweating affected by the Six Atmospheric Influences and water. And detailed explanations of disease mechanism a sweat leading to another disease. 6. There are descriptions about various sweat absent situations.