• The Journal of Advanced Prosthodontics
• /
• v.1 no.2
• /
• pp.85-90
• /
• 2009

STATEMENT OF PROBLEM. Over the years, resin-bonded fixed partial dentures (RBFPDs) have gone through substantial development and refinement. Several studies examined the biomechanics of tooth preparation and framework design in relation to the success rate of RBFPDs and considered retention and resistance form essential for increase of clinical retention. However, these criteria required preparations to be more invasive, which violates not only the original intentions of the RBFPD, but may also have an adverse effect on retention due to loss of enamel, an important factor in bonding. PURPOSE. The object of this in vitro study was to compare the dislodgement resistance of the new types of RBFPDs, the conventional three-unit fixed partial denture, and conventional design of RBFPD (Maryland bridge). MATERIAL AND METHODS. Fifty resin mandibular left second premolars and second molars were prepared on dentiforms, according to the RBFPD design. After model fabrication (five group, n = 10), prostheses were fabricated and cemented with zinc phosphate cement. After cementation, the specimens were subjected to tensile loading at a cross head speed of 4 mm/min in a universal testing machine. The separation load was recorded and analyzed statistically using one-way analysis of variance followed by Duncan's multiple range test. RESULTS. Group V, the pin-retained RBFPDs, had the highest mean dislodgement resistance, whereas specimens of group II, the conventional RBFPDs, exhibited a significantly lower mean dislodgement resistance compared to the other 4 groups (P <.05). There were no significant differences between group I, III, and IV in terms of dislodgement resistance (P>.05). Group V had the highest mean MPa (N/$mm^2$) (P <.05). There was no significant difference between groups I, II, III and IV (P > .05). CONCLUSION. Within the limits of the design of this in vitro study, it was concluded that: 1. The modified RBFPDs which utilizes the original tooth undercuts and requires no tooth preparation, compared with the conventional design of RBFPDs, has significantly high dislodgement resistance (P < .05). 2. The modified RBFPDs which utilizes the original tooth undercuts and requires minimal tooth preparation, compared with the conventional FPDs, has significantly no difference in retention and dislodgement resistance)(P>.05). 3. The pin-retained FPDs showed a high dislodgement resistance compared to the conventional three-unit FPDs (P<.05).

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.2
• /
• pp.37-43
• /
• 1999

Modules of the system that requires large capacity and high-speed information processing are implemented in the form of MCM that allows high-speed data processing, high density circuit integration and widely applied to such fields as ATM, GPS and PCS. Hence we developed the ATM switching module that is consisted of three chips and 2.48 Gbps data throughput, in the form of 10 multi-layer by Cu/Photo-BCB and 491pin PBGA which size is $48 \times 48 \textrm {mm}^2$. hnologies required for the development of the MCM includes extracting parameters for designing the substrate/package through the interconnect characterization to implement the high-speed characteristics, thermal management at the high-density MCM, and the generation of the testability that is one of the most difficult issues for developing the MCM. For the development of the ATM Switching MCM, we extracted signaling delay, via characteristics and crosstalk parameters through the interconnect characterization on the MCM-D. For the thermal management of 15.6 Watt under the high-density structure, we carried out the thermal analysis. formed 1.108 thermal vias through the substrate, and performed heat-proofing processing for the entire package so that it can keep the temperature less than $85^{\circ}C$. Lastly, in order to ensure the testability, we verified the substrate through fine pitch probing and applied the Boundary Scan Test (BST) for verifying the complex packaging/assembling processes, through which we developed an efficient and cost-effective product.

• Nuclear Engineering and Technology
• /
• v.54 no.7
• /
• pp.2728-2735
• /
• 2022

The research on the flow and heat transfer characteristics of lead bismuth(LBE) is significant for the thermal-hydraulic calculation, safety analysis and practical application of lead-based fast reactors(LFR). In this paper, a new CFD model is proposed to solve the thermal-hydraulic analysis of LBE. The model includes two parts: turbulent model and turbulent Prandtl, which are the important factors for LBE. In order to find the best model, the experiment data and design of 19-pin hexagonal rod bundle with spacer grid, undertaken at the Karlsruhe Liquid Metal Laboratory (KALLA) are used for CFD calculation. Furthermore, the turbulent model includes SST k - 𝜔 and k - 𝜀; the turbulent Prandtl includes Cheng-Tak and constant (Pr_t =1.5,2.0,2.5,3.0). Among them, the combination between SST k - 𝜔 and Cheng-Tak is more suitable for the experiment. But in the low Pe region, the deviation between the experiment data and CFD result is too much. The reason may be the inlet-effect and when Pe is in a low level, the number of molecular thermal diffusion occupies an absolute advantage, and the buoyancy will enhance. In order to test and verify versatility of the model, the NCCL performed by the Nuclear Thermal-hydraulic Laboratory (Nuthel) of Xi'an Jiao tong University is used for CFD to calculate. This paper provides two verification examples for the new universal model.

• Korean Journal of Food Science and Technology
• /
• v.40 no.4
• /
• pp.443-448
• /
• 2008

In this study, black garlic was produced by aging under high temperature $(70^{\circ}C)$ and high humidity (90% RH) conditions. Then, the physiological activity and antioxidative effects of its extract were compared to those of normal garlic extract. The black garlic extract had a 2.5-fold higher total polyphenol content than that of the normal garlic extract, showing levels of 10.0 mg/g and 3.7 mg/g, respectively. At the $1,000{\mu}g/mL$ concentration, the black garlic and normal garlic extracts had electron donating abilities of 101.9% and 12.9%, respectively. For their nitritescavenging effects, the normal garlic extract showed slightly higher scavenging activity than the black garlic extract at the 5 mg/mL concentration; whereas the black garlic extract had a slightly higher effect at concentrations above 20 mg/mL. In terms of their superoxide dismutase activities, the black garlic extract showed a 10-fold higher activity as compared to the normal garlic extract at the 20 mg/mL concentration. Furthermore, at 50 mg/mL, the angiotensin converting enzyme inhibitory effects of the normal garlic and black garlic extracts were approximately 52.7% and 88.8%, respectively. These results indicate that the antioxidant activity and ACE inhibitory effects of the black garlic extract were greater than those of the normal garlic extract.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.269-269
• /
• 2012

A new ion source has been designed, fabricated, and installed at the NBTS (Neutral Beam Test Stand) at the KAERI (Korea Atomic Energy Research Institute) site. The goalis to provide a 100 keV, 2MW deuterium neutral beam injection as an auxiliary heating of KSTAR (Korea Super Tokamak Advanced Research). To cope with power demand, an ion current of 50 A is required considering the beam power loss and neutralization efficiency. The new ion source consists of a magnetic cusp bucket plasma generator and a set of tetrode accelerators with circular copper apertures. The plasma generator for the new ion source has the same design concept as the modified JAEA multi-cusp plasma generator for the KSTAR prototype ion source. The dimensions of the plasma generator are a cross section of $59{\times}25cm^2$ with a 32.5 cm depth. The anode has azimuthal arrays of Nd-Fe permanent magnets (3.4 kG at surface) in the bucket and an electron dump, which makes 9 cusp lines including the electron dump. The discharge properties were investigated preliminarily to enhance the efficiency of the beam extraction. The discharge of the new ion source was mainly controlled by a constant power mode of operation. The discharge of the plasma generator was initiated by the support of primary electrons emitted from the cathode, consisting of 12 tungsten filaments with a hair-pin type (diameter = 2.0 mm). The arc discharge of the new ion source was achieved easily up to an arc power of 80 kW (80 V/1000 A) with hydrogen gas. The 80 kW capacity seems sufficient for the arc power supply to attain the goal of arc efficiency (beam extracted current/discharge input power = 0.8 A/kW). The accelerator of the new ion source consists of four grids: plasma grid (G1), gradient grid (G2), suppressor grid (G3), and ground grid (G4). Each grid has 280 EA circular apertures. The performance tests of the new ion source accelerator were also finished including accelerator conditioning. A hydrogen ion beam was successfully extracted up to 100 keV /60 A. The optimum perveance is defined where the beam divergence is at a minimum was also investigated experimentally. The optimum hydrogen beam perveance is over $2.3{\mu}P$ at 60 keV, and the beam divergence angle is below $1.0^{\circ}$. Thus, the new ion source is expected to be capable of extracting more than a 5 MW deuterium ion beam power at 100 keV. This ion source can deliver ~2 MW of neutral beam power to KSTAR tokamak plasma for the 2012 campaign.

• The Korean Journal of Nuclear Medicine
• /
• v.29 no.4
• /
• pp.533-540
• /
• 1995

Attenuation correction is important in producing quantitative positron emission tomography (PET) images. Conventionally, photon attenuation effects are corrected using transmission measurements performed before tracer administration. The pre-injection transmission measurement approach may require a time delay between transmission and emission scans for the tracer studies requiring a long uptake period, about 45 minutes for F-18 deoxyglucose study. The time delay will limit patient throughput and increase the likelihood of patient motion. A technique lot performing simultaneous transmission and emission scans (T+E method) after the tracer injection has been validated. The T+E method substracts the emission counts contaminating the transmission measurements to produce accurate attenuation correction coefficients. This method has been evaluated in experiments using a cylindrical phantom filled with background water (5750 cc) containing $0.4{\mu}Ci/cc$ of F-18 fluoride ion and one insert cylinder (276 cc) containing $4.3{\mu}Ci/cc$. GE $Advance^{TM}$ PET scanner and Ge-68 rotating pin sources for transmission scanning were used for this investigation. Post-injection transmission scan and emission scan were peformed alternatively over time. The error in emission images corrected using post-infection transmission scan to emission images corrected transmission scan was 2.6% at the concentration of $1.0{\mu}Ci/cc$. No obvious differences in image quality and noise were apparent between the two images. The attenuation correction can be accomplished with post-injection transmission measurement using rotating pin sources and this method can significantly shorten the time between transmission and omission scans and thereby reduce the likelihood of patient motion and increase scanning throughput in PET.

• Asian-Australasian Journal of Animal Sciences
• /
• v.17 no.9
• /
• pp.1227-1231
• /
• 2004

Pig oocytes contain high levels of lipids in the ooplasm, which reduces the visibility of the germinal vesicle (GV) under microscopic examination. Therefore, the purposes of this study were to investigate the effects of relative centrifugation force (RCF) on the visibility and maturation rates of the GV stage oocytes after centrifugation. In Experiment 1, cumulus-oocyte-complexes (COCs) were collected from slaughterhouse ovaries and randomly allocated to different RCFs (3,000 rpm: 970 g; 6,000 rpm: 3,900 g; or 10,000 rpm: 10,840 g) for 10 or 20 min. Percentages of visible GV were 76-79% in the oocytes centrifuged with 10,000 rpm, which were significantly higher (p<0.01) than those with 3,000 and 6,000 rpm. No significant differences in GV visibility were observed among oocytes with different lengths of centrifugation (p<0.05) regardless of the RCFs. In esperiment 2, the maturation rate of the oocyte was found significantly lower in the 20 min than in the 10 min group received 10,840 g of RCF (30 vs. 75%, p<0.05). In conclusion, the GV of porcine oocytes can be clearly visible by centrifugation at 10,840 g for 10 min without compromising their subsequent maturation rates and a longer centrifugation time (20 min) had no beneficial influence on the visibility of GV stage pig oocytes.

• Journal of the Korean Geosynthetics Society
• /
• v.3 no.1
• /
• pp.3-15
• /
• 2004

Geogrid reinforced soil structures with segmental block facing have been increased since 1990's, because of the convenience of installation and the flexible appearance. In this paper, the behavior of the segmental reinforced retaining wall was analysed with the results of field monitoring. The height and length of reinforced wall are 12m and 25m, respectively. The field measurement equipments are horizontal and vertical earth pressure cells, settlement plate, strain gauge, inclinometer, and displacement pin. Based on the field monitoring, the horizontal earth pressure was approximately 0.3times higher than that of the theoretical method and the maximum tensile strength of reinforcement was 26.2kN/m. The displacement of facing wall was 23mm at the point of 7.1m height of the wall and toward the wall facing. The results of the study indicate that the segmental reinforced retaining wall is in a stable condition because of good compaction & reinforcement effects, and long period of construction time. Finally, the computer program of SRWall is very useful tool to design the segmental reinforced retaining wall.

• Microbiology and Biotechnology Letters
• /
• v.35 no.3
• /
• pp.203-209
• /
• 2007

Soybean milk cake (SMC) was used for the solid-state fermentation by Bacillus subtilis PUL-A isolated from soybean milk cake. In the presence of 5% glutamate the maximum production of biopolymer (59.9 g/kg) was performed by fermentation at $42^{\circ}C$ for 24 hr. The recovered biopolymer was consisted of 87% $\gamma$-polyglutamic acid with molecular weight of $1.3{\times}10^6$ dalton and other biopolymer. The biopolymer solution showed the great decrease in consistency below pH 6.0, regardless of the molecular weight of PGA. Biopolymer solution has a typical pseudoplastic flow behavior and yield stress. The consistency of biopolymer solution was greatly decreased by increasing heating time and temperature in acidic condition compared to the alkaline condition. In kaolin clay suspension, the flocculating activity of biopolymer was the highest value with 15 mg/L biopolymer and 4.5 mM $CaCl_2$, but decreased greatly with $FeCl_3$. The flocculating activity of biopolymer was maximum at pH5, but decreased drastically by heating at $60{\sim}100^{\circ}C$. In particular, biopolymer with native PGA showed the efficient flocculating activity compared to that of modified biopolymer containing low molecular weight of PGA.

• Fashion & Textile Research Journal
• /
• v.22 no.5
• /
• pp.686-695
• /
• 2020

The present study evaluated the manual dexterity and usability of conductive gloves when operating touchscreen devices in the cold. Twelve male subjects (23.3±1.5 years in age) participated in three experimental conditions: no gloves, fabric conductive and lambskin conductive gloves. Manual dexterity was tested using both Purdue Pegboard (PP) and ASTM dexterity tests at an air temperature of 5℃ and air humidity of 30%RH. Glove usability was tested through the following touchscreen tests: tap, double tap, long tab, drag, flick, and multi-touch. The results showed that manual dexterity according to the PP (2.5 mm of a pin diameter) and ASTM tests (8 mm of a stick diameter) was worse for the two glove conditions than for the no glove condition (p<.005). PP dexterity was better for the fabric glove condition than for the lambskin glove condition (p<.05); however, there was no difference in ASTM dexterity between the two glove conditions. Hand and finger skin temperatures were higher for the glove conditions than the bare hand condition (p<.05), with no differences between the two glove conditions. The touchscreen usability was the best for the no glove condition, followed by fabric gloves (p<.05). Wearing either fabric or lambskin gloves diminishes hand dexterity while maintaining hand and finger temperatures at higher levels. For improved hand dexterity in dealing with small numbers, letters on a touchscreen in cold environments, we recommend wearing fabric conductive gloves rather than lambskin conductive gloves.