• Tribology and Lubricants
• /
• 제34권6호
• /
• pp.300-306
• /
• 2018

In this study, the performance of foil thrust bearings was investigated by performing bearing take-off and load capacity tests, using an in-house designed and manufactured vertical bearing test rig. The mean take-off rotational speed and maximum load capacity of the bearing specimen were ~18,000 rpm and ~80 kPa, respectively. The vertical bearing test rig was observed to yield higher coefficients of friction and frictional torques than a horizontal bearing test rig under identical test conditions. This was a result of its structural characteristics, in that the bearing specimen is placed atop the thrust runner, which keeps it from being separated from the runner after the bearing take-off. In addition, bearing take-off was observed at a higher runner rotational speed as this structure keeps air from flowing between the top foil and runner surfaces, which requires a higher runner speed. The parallel alignment between the bearing specimen and runner surfaces can be maintained within a certain range more easily in a vertical test rig than in a horizontal test rig. Because of these advantages, Korean Industrial Standard, KS B 2060, recommends a vertical bearing test rig as the standard test device for foil thrust bearings.

• 한국강구조학회 논문집
• /
• 제18권6호
• /
• pp.769-782
• /
• 2006

상시 운행 열차는 운행 속도 대역폭이 한정되어 있기 때문에 속도에 따른 교량의 동적응답 특성 파악에는 한계가 있다. 따라서 본 연구에서는 교량상을 통과하는 열차 속도와 교량의 동적응답의 상관관계를 파악하기 위하여 실운행 디젤 기관차 1량에 의한 증속실험을 실시하였다. 가속도 응답특성 분석을 위하여 지점부를 제외한 전구간에 걸쳐 등간격으로 7개의 수직가속도와 중앙부에 1개의 수평가속도계를 부착하였다. 교량의 중앙부에는 연직방향과 횡방향 거동특성 파악을 위하여 수직 변위계, 수평 변위계, 휨변형률계를 각각 1개씩 설치하였다. 실험 차량을 대상 교량의 중앙부와 지점부에 정적재하 후 5km/h부터 90km/h까지 10km/h씩 증속하였고, 각 속도 대역별로 2회씩 반복하여 실험을 실시하였다. 실측 데이터의 필터링 방법에 따른 진동 평가 방법의 적절성을 검토하였고, 연직방향 진동가속도 대비 횡방향 진동수준을 평가하였으며, 속도에 따른 처짐, 변형률 및 윤중변동 특성을 검토하였다.

• 열처리공학회지
• /
• 제11권3호
• /
• pp.159-167
• /
• 1998

In this study, friction-wear test was carried out on the carburized layer depth of a mechanical structure steel SNCM carburized with RX and LPG for 7hrs at $930^{\circ}C$ and also the wear properties of wear loss, wear rate, coefficient of friction, friction force and friction temperature were investigated. The wear properties for carburized layer of SNCM were tested on dry condition at the room temperature by the thrust load of 49~245N range at sliding speed of 0.2m/sec and the sliding speed of 0.2~1.0m/sec range at thrust load of 98N. Wear loss on the depth of carburizing layer was increased with increasing of thrust load and sliding speed, and with decreasing of hardness. The condition of worn surfaces were showed mild wear at less than the thrust load of 98N and sliding speed of 0.6m/sec but were showed severe wear at more than 98N and 0.6m/sec. The friction load and temperature were increased with increasing of thrust load but with increasing sliding speed was appeared minimum at 0.6m/sec. With increasing thrust load the wear rate was increased and the coefficient of friction was decreased, but with increasing sliding speed the wear rate and the coefficient of friction were decreased in 0.2~0.6m/sec and increased in 0.6~1.0m/sec, therefore 0.6m/sec in this testing is a transition velocity.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2001년도 춘계학술대회 논문집
• /
• pp.217-221
• /
• 2001

Barber bogie and Y25 bogie is the main bogie of freight car which is used in the Korean railway. In case of Barber bogie and a mixed formation tile maximum speed limit of empty car is 70 km/h and that of loaded car is 90 km/t and also it runs a speed of 110 km/h in time of an exclusive formation of Y25 bogie. The car named as high speed freight car at present is Y25 bogie which modeled on the Y25 bogie or Europe developed in 1993, Y25 bogie has no problem about the running capacity up to the speed of 110 km/h, but it works as limiting factors to tile increasing cost of maintenance and repair expenses which caused by repair of bogie and the cost of materials. This study is going to describe the contents examined by analysis and tests, aimed at being used as an index of plan in the future through the strength test of high speed freight car which is used now.

• 한국대기환경학회지
• /
• 제1권1호
• /
• pp.83-92
• /
• 1985

In odrder to survey the emission level of air pollutants from diesel vehicles, was measured CO, HC, NOx and smoke of 4 types of domestic-use diesel engines under various conditions. The emission of CO, HC and NOx tested by 6-Mode test method and smoke emission by full load test met the permissible vehicle emission standard. Pollutant emission rates of diesel engines were different according to engine operating conditions, that is, engine load and engine speed. Generally, CO and HC was emitted more at low load and NOx at high load but the trend was quite different by the type of engines. In exhaust gas, $NO_2$ portion of NOx emission was high, specially at low speed and low load. The correlation equation between CLD(NOx) and NDIR(NO) method of nitrogen of nitrogen oxides analysis was y = 1.10x - 3.48 (y: CLD method) as a result of 6-mode test.

• 산업기술연구
• /
• 제25권B호
• /
• pp.157-164
• /
• 2005

Two methods, the bin averaging method and least square method, are often used in calibrating wind turbine test sites. The objective of this work was to determine a better method to predict the wind speed at wind turbine installing point. The calibration was done at the test site on a complex terrain located in Daegwallyeong, Korea. It was performed for two different cases based on the IEC 61400-12 power performance measurement standard. The wind speeds averaged for 10 minutes ranged between 4 m/s and 16 m/s. The wind-direction bins of each meteorological mast were 10 degrees apart, and only the bins having data measured for more than 24 hours were employed for the test site calibration. For both cases, the two methods were found to yield almost same results which estimated real wind speed very closely.

• International Journal of Aeronautical and Space Sciences
• /
• 제2권1호
• /
• pp.103-109
• /
• 2001

Productivity enhancement program of wind tunnel testing has begun at Korea Aerospace Research Institute Low Speed Wind Tunnel (KARI LSWT). A previous test record of a canard airplane model was adopted to examine the current status of wind tunnel testing efficiency. The time consumed to perform testing activities from the model preparation to data collection was broken down and the results were compared with those of the recent Boeing low speed test result. The efforts to improve the wind tunnel productivity consisted of the installation of mini crane underneath of test section, fabricating lift device for image fairings, model configuration changing rigs and the modifications of external balance system. Time reductions for changing strut interface platform and installation of image fairings. These effects showed more than 70% improvement over the previous test time. Integration of the new and modified systems will improve productivity of wind tunnel testing in KARI LSWT.

• 한국추진공학회지
• /
• 제20권6호
• /
• pp.101-112
• /
• 2016

초음속 비행체의 항력 감소 기초 실험을 위한 플라즈마 분사장치의 특성에 대해 분석하였다. 플라즈마 종류는 고압에서 발생이 가능한 열 플라즈마가 적합하다. 열 플라즈마를 발생하기 위해 플라즈마 토치를 사용한다. 플라즈마 토치는 고압 고속 분사가 가능하기 때문에 플라즈마 분사 제트에 적합한 플라즈마 발생장치이다. 본 연구에서는 확보한 플라즈마 토치에 대해 분석 및 정리하였고 기초 연구를 수행하였다. 그 결과 플라즈마 제트 발생의 주요 변수로는 플라즈마 토치의 전극 간격과 공급 기체의 압력으로 고려되었다.

• 한국유체기계학회 논문집
• /
• 제15권4호
• /
• pp.27-32
• /
• 2012

Gas turbines for an aircraft have the start and restart capabilities within their flight envelop. It is an important item for engine qualification and substantiated with the test. Experimental investigations were carried out to find the relation between the corrected torque and the corrected rotating speed of an air turbine starter in this study. A dedicated air supply system for the air turbine starter and a special device to measure the torque and the rotating speed of the air turbine starter were developed and installed at the altitude engine test facility in Korea Aerospace Research Institute. Experimental results show that the relations between the corrected torque and the corrected rotating speed of the air turbine starter are linear and the inlet temperature and pressure conditions for the air turbine starter were found out to provide minimum required torque for the engine qualification test at various altitude. The start and restart tests for the currently developing engine were successfully performed using this experimental results.

• 해양환경안전학회지
• /
• 제28권5호
• /
• pp.800-808
• /
• 2022

국제해사기구에서는 해상에서의 선박의 충돌방지와 그로 인한 해양환경의 보호를 목적으로 1993년 11월 선박조종성능에 대한 잠정지침을 채택한 이후, 축적된 데이터를 바탕으로 2002년 12월 선박조종성능에 대한 확정된 지침을 채택하였다. 하지만 채택된 지침은 만재상태, 등흘수 및 선박의 최대 출력(MCR)의 85 %에 해당되는 선속의 최소 90 % 이상에서의 지침으로, 동 지침은 항해사에게 필요한 실 항해조건에서의 조종성능 정보를 제공하는 데 한계가 있다. 따라서 본 연구에서는 항해사, 선장 및 선박조종에 대한 식견을 갖추고 있는 전문가를 대상으로 빈도분석과 AHP 분석기법을 실시하여 현 지침에 대한 활용도 및 실제 선박조종에 필요한 정보가 무엇인지를 식별하였다. 연구결과 선박을 운항하는 항해사에게 필요한 조종성능 정보는 5~10°의 소각도에서의 선회권 정보, 항해속력(Sea speed)이 아닌 조종속력(Maneuvering speed)에서의 z-test 정보라는 것을 확인하였고, 속도제어 관련하여서는 항해속력 및 만재상태에서의 정지성능에 대한 정보보다 감속타력, 가속타력 등에 대한 정보가 더 필요하다는 것을 확인하였다. 도출된 결과는 선박을 조종하는 항해사에게 필요한 선박조종성능기준 지침마련에 대한 기초자료로 활용도가 높을 것으로 사료된다.