• 한국도로학회논문집
• /
• 제15권2호
• /
• pp.11-18
• /
• 2013

PURPOSES : This study presents the noise level and frequency characteristics investigated in the national highways with the consideration of various measuring conditions and/or methods. METHODS : The noise levels on the asphalt concrete pavement(ACP) and the jointed plain concrete pavement(JPCP) of the national highway were measured and analysed with respect to three variables, i.e., pavement type, surface condition, and measurement distance. The PASS-By method is utilized for the noise measurement and then using CPB spectrum analysis method with 1/3 octave bandwidth, the noise levels and frequency characteristics were calculated for two-second periods before and after the peak noise. RESULTS : Depending on the pavement type, the noise level was changed as the average noise levels are 73.3dB(A) and 78.3dB(A) for ACP and JPCP, respectively. With respect to the effect of surface condition, the average noise levels for crack H(high), M(medium), and L (low) sections are 77.4dB(A), 77.4dB(A), and 78.1dB(A), respectively. Regarding the measurement distance, 1.2meter difference in measuring location reduces 1.6dB(A) of noise level; the average noise levels at 5.3m and 7.5m from the centerline of outer lane are 72.8dB(A) and 71.2dB(A), respectively. It should be noted that the noise levels are slightly different as a function of vehicle speed and type. However, the overall trends for each case was similar. It was found that the domain frequency bands for ACP and JPCP were 400Hz~2000Hz and 500Hz~2000Hz, respectively. CONCLUSIONS : Based on the analysis with the measured noise date from national highway, it was concluded that the noise level and frequency band vary depending on the various conditions. It was also found that some variables significantly affect the noise level while others do not. With further systematic investigation, the comprehensive noise characteristics on the national highway can be achieved. Using such database, it is possible to develop the fundamental noise reduction technology.

• 한국측량학회지
• /
• 제35권6호
• /
• pp.599-608
• /
• 2017

아스팔트 도로표면의 균열은 자동차 속도, 연료 소비량, 도로주행 시 승차감, 도로표면의 내구성 등에 영향을 미친다. 이러한 도로의 균열은 장시간 방치 시 상당히 위험한 결과를 초래할 수 있다. 사람이 직접 균열을 찾아 내어 적절한 조치를 취하기에는 너무 많은 시간과 비용이 소모된다. 또한 고가의 레이저 장비 차량들을 활용하기에는 초기 비용과 장비 운용에 어려움을 가진다. 이에 본 연구에서는 UAV 영상을 이용해 컴퓨터 비전 기반의 관심영역(ROI: Region of Interest) 설정과 에지 검출 알고리즘을 적용하여 도로표면의 균열탐지 방안을 제시하였다. 본 연구 결과는 무인항공기를 활용한 효율적인 도로표면 결함탐지 및 유지보수 방안으로 제시될 수 있다. 또한 도로 이외 건물빌딩의 외벽, 대규모 저장 탱크 등 다양한 건축, 토목 구조물에 발생된 균열 탐지에 활용이 가능하며 비용저감 효과를 기대할 수 있을 것이다.

• 한국환경복원기술학회지
• /
• 제13권5호
• /
• pp.38-50
• /
• 2010

Expressways are often upgraded by widening the lanes and/or by reshaping the roads to be more linear for faster travel time. However, during the process of improving the route of the expressways, the areas where the old expressways used to be are often unused and abandoned. When these neglected sites are left alone, they often become dump sites causing pollution and impacting the surrounding environment. Therefore, it is important to restore the abandoned expressway sites to its full natural beauty. In this study, the abandoned expressway at the Soksa interchange in Pyungchang county, located in Kangwon province was studied for establishing the model of ecological restoration project. Considering the characteristics of the site, the target flora species was chosen to be Quercus species and the target fauna species as amphibians. After the target species were carefully chosen, each species' habitat requirements were studied in order to figure out the appropriate methods toward habitat restoration specifically for these species. In addition, to determine the most efficient method toward restoration of abandoned expressways, the study utilized the planting hole techniques, the crack techniques, and the colonization techniques. In terms of the spatial organization, public education program is incorporated at the main entrance area and the programs for experimenting, and developing vegetation and habitat restoration techniques are placed in the vicinity. In the master plan-to provide natural ecosystem at the site-ASCON (asphalt concrete) was removed first, then plans for restoration including species' habitat restoration were established. Furthermore, the project included plans for improving water quality polluted through non-point source considering the surrounding nearby road and farm lands. Finally, the study established a planning process that will experimentally apply to the abandoned expressway restoration method. In the future, there will be a continuous monitoring of the methods applied to verify if the restoration methods are effective. Also, new restoration techniques should be available according to a variety of abandoned expressways' characteristics.

• Advances in concrete construction
• /
• 제15권6호
• /
• pp.419-430
• /
• 2023

In this study, the effect of two types of aggregates (fly ash aggregate and shale aggregate) on the density, strength, and durability of preplaced lightweight aggregate concrete (PLWAC) was studied. The results showed that the 7 - 28 days strength of concrete prepared with fly ash aggregates (high water absorption rate) significantly increased, which could attribute to the long-term water release of fly ash aggregates by the refined pore structure. In contrast, the strength increase of concrete prepared with shale aggregates (low water absorption rate) is not apparent. Although PLWAC prepared with fly ash aggregates has a lower density and higher strength (56.8 MPa @ 1600 kg/m³), the chloride diffusion coefficient is relatively high, which could attribute to the diffusion paths established by connected porous aggregates and the negative over-curing effect. Compared to the control group, the partial replacement of fly ash aggregates (30%) with asphalt emulsion (20% solid content) coated aggregates can reduce the chloride diffusion coefficient of concrete by 53.6% while increasing the peak load obtained in a three-point bending test by 107.3%, fracture energy by 30.3% and characteristic length by 103.5%. The improvement in concrete performance could be attributed to the reduction in the water absorption rate of aggregates and increased energy absorption by polymer during crack propagation.

• 한국지리정보학회지
• /
• 제10권1호
• /
• pp.35-46
• /
• 2007

본 연구에서는 수치영상을 이용하여 아스팔트 콘크리트포장 도로를 대상으로 차량에 비디오 카메라를 설치하여 도로에서 일정하게 차량속도를 유지하면서 촬영된 수치 영상정보로 객체 지향적인 언어인 Delphi를 이용하여 도로노면정보(균열, 소성변형, 종평탄성)를 획득할 수 있는 도로노면 관리시스템을 개발하고, 개발된 시스템은 동영상 및 그래프를 이용하여 시각화 효과를 증진시킬 수 있도록 하였다. 다중영상표정과 광속조정법에 의해 결정된 도로노면의 3차원 좌표의 정확도를 분석한 결과 표준 오차의 평균은 X방향으로 0.0427m, Y방향으로 0.0527m, Z방향으로 0.1539m로 나타났다. 이 값은 우리나라에서 현재 제작하여 사용하고 있는 축척 1:1,000 이하의 지도제작 및 GIS 자료로서 충분히 활용성이 있다. 수치영상을 이용하여 12개소에 대하여 균열폭의 정확도를 분석한 결과 표준오차가 ${\pm}0.256mm$로 정밀도가 아주 높게 나타났으며, 또한 소성변형량을 비교하기 위하여 4개소의 실측된 횡단면과 영상으로부터 추출된 횡단면을 비교한 결과 최대 오차는 10.80mm로 나타났으나, 작업능률면에서는 실용성이 있다고 판단된다.

• 한국도로학회논문집
• /
• 제12권4호
• /
• pp.211-218
• /
• 2010

콘크리트 슬래브는 온도 및 수분의 영향을 받아 체적이 변화된다. 이때 슬래브와 보조기층 간의 마찰저항이 슬래브 체적변화를 구속하여 인장응력이 발생되고 경우에 따라 균열이 유발되기도 한다. 따라서 연구자들은 Push-off 실험을 실시하여 슬래브와 보조기층간의 마찰특성을 파악하려고 노력해 왔다. 최근에는 마찰특성에 의한 콘크리트 포장의 거동을 유한요소법으로 해석하려는 연구가 수행되었다. 본 연구에서는 국내 콘크리트 포장에 주로 사용되는 린콘크리트, 쇄석, 아스팔트 보조기층에 대하여 실시된 마찰실험 결과를 바탕으로 슬래브와 보조기층 간 마찰특성을 조사하였다. 비선형의 마찰저항과 변위의 관계를 이중선형화하는 에너지 방법이 제시되었다. 마찰실험을 3차원 유한요소 프로그램 ABAQUS로 모형화하였으며 해석결과를 실험결과와 비교하여 모형을 검증하였다. 비선형과 이중선형 마찰저항-변위 관계를 각각 입력값으로 사용하여 얻은 해석결과를 비교하여 에너지 방법으로 개발된 이중선형 모형의 타당성을 검증하였다. 일반적인 국내 콘크리트 포장을 ABAQUS와 EverFE로 모형화하고 해석결과를 비교하여 이중선형 모형의 적용성을 평가하였다.

• 한국도로학회논문집
• /
• 제7권2호
• /
• pp.33-43
• /
• 2005

시멘트 안정처리 기층은 강성기층으로 러팅 저항성이 크고 상부하중 분산, 피로균열저항, 기층 보조기층의 파손 감소의 효과가 있으며 경제성이 뛰어나다는 장점이 있다. 그러나 건조수축에 의한 반사균열로 인하여 국내에서는 CTB가 전혀 적용되지 못하고 있는 실정이다. 따라서 본 연구는 국내에 CTB적용을 위한 기초연구로써 반사 균열을 최소화하기 위해 건조수축을 억제할 수 있는 저수축 시멘트 안정처리 기층 재료개발을 시도하였다. 건조수축 이론을 고찰하여 건조수축 저감방안을 수립하였고 건조수축에 미치는 영향인자를 선정하였으며, 각 혼화재의 메커니즘을 분석한 후 실내 실험 및 현장실험을 수행하였다. 예비실험을 통하여 플라이 애쉬 첨가비율은 25%로 제안하였고 시멘트량은 모든 배합이 도로공사 린 기층의 허용강도를 만족하는 7%로 하였다. 본 실험 결과를 바탕으로 강도, 건조수축율, 경제성을 고려한 결과, 플라이 애쉬 25%, 플라이 애쉬 25%에 팽창재를 10%를 혼합한 배합을 대안으로 결정하였다. 실내실험에서 결정된 대안을 현장 실험에 적용한 결과 플라이 애쉬(25%)+팽창재(10%)가 최적의 저수축 시멘트 안정 처리 기층 배합임을 제시하였다.

• 한국도로학회논문집
• /
• 제19권5호
• /
• pp.107-115
• /
• 2017

PURPOSES : The piezoelectric energy road analysis technology using a three-dimensional finite element method was developed to investigate pavement behaviors when piezoelectric energy harvesters and a new polyurethane surface layer were installed in field conditions. The main purpose of this study is to predict the long-term performance of the piezoelectric energy road through the proposed analytical steps. METHODS : To predict the stresses and strains of the piezoelectric energy road, the developed energy harvesters were embedded into the polyurethane surface layer (50 mm from the top surface). The typical type of triaxial dump truck loading was applied to the top of each energy harvester. In this paper, a general purpose finite element analysis program called ABAQUS was used and it was assumed that a harvester is installed in the cross section of a typical asphalt pavement structure. RESULTS : The maximum tensile stress of the polyurethane surface layer in the initial fatigue model occurred up to 0.035 MPa in the transverse direction when the truck tire load was loaded on the top of each harvester. The maximum tensile stresses were 0.025 MPa in the intermediate fatigue model and 0.013 MPa in the final fatigue model, which were 72% and 37% lower than that of the initial stage model, respectively. CONCLUSIONS : The main critical damage locations can be estimated between the base layer and the surface layer. If the crack propagates, bottom-up cracking from the base layer is the main cracking pattern where the tensile stress is higher than in other locations. It is also considered that the possibility of cracking in the top-down direction at the edge of energy harvester is more likely to occur because the material strength of the energy harvester is much higher and plays a role in the supporting points. In terms of long-term performance, all tensile stresses in the energy harvester and polyurethane layer are less than 1% of the maximum tensile strength and the possibility of fatigue damage was very low. Since the harvester is embedded in the surface layer of the polyurethane, which has higher tensile strength and toughness, it can assure a good, long-term performance.