• Advances in nano research
• /
• 제8권4호
• /
• pp.307-322
• /
• 2020

In this article, free vibration of double-walled carbon nanotubes (DWNT) based on nonlocal Kelvin's model have been investigated. For this purpose, a nonlocal Kelvin's model is established to observe the small scale effect. The wave propagation is employed to frame the governing equations as eigenvalue system. The influence of nonlocal parameter subjected to different end supports has been overtly examined. The new set of inner and outer tubes radii investigated in detail against aspect ratio. The influence of boundary conditions via nonlocal parameter is shown graphically. Due to small scale effect fundamental frequency ratio decreases as length to diameter ratio increases. Small scale effect becomes negligible on all end supports for the higher values of aspect ratio. With the smaller inner tube radius double-walled CNT behaves more sensitive towards nonlocal parameter. The results generated furnish the evidence regarding applicability of nonlocal model and also verified by earlier published literature.

• 한국건설순환자원학회논문집
• /
• 제5권1호
• /
• pp.14-20
• /
• 2017

UHPC는 초고층 건물 및 초장대교의 경우 필연적으로 사용되어진다. 일반적으로 콘크리트는 압축강도보다 낮은 휨강도 및 인장강도를 가지므로 취성균열이 발생하여 에너지 흡수능력이 저하된다. 이러한 문제를 해결하기 위해 본 연구에서는 강섬유의 혼입율과 형상비가 UHPC의 기계적 물성에 미치는 영향을 조사하고자한다. 시리즈 I에서, 20mm 직선형 강섬유가 0, 1.0, 1.3, 1.5 및 2.0%의 혼입율로 첨가되었다. 시리즈 II에서는 16mm 강섬유를 0, 1, 1.5%로 혼입한 후 형상비에 따라 역학적 성질을 조사하였다. 실험결과, 압축강도의 차이는 미비했다. 하지만 휨강도 및 인장강도와 관련하여 혼입율 및 형상비가 증가함에 따라 휨성능 및 인장성능이 개선되었다.

• Journal of Mechanical Science and Technology
• /
• 제18권11호
• /
• pp.1932-1940
• /
• 2004

Although the previous researches evaluated the fatigue behavior of Al/GFRP laminates using the traditional fracture mechanism, their researches were not sufficient to do it : the damage zone of Al/GFRP laminates was occurred at the delamination zone instead of the crack-metallic damages. Thus, previous researches were not applicable to the fatigue behavior of Al/GFRP laminates. The major purpose of this study was to evaluate delamination behavior using the relationship between crack length (a) and delamination width (b) in Al/GFRP laminate. The details of investigation were as follows: 1) Relationship between the crack length (a) and the delamination width (b), 2) Relationship between the delamination aspect ratio (b/a) and the delamination area rate ((A$\_$D/)/subN// (A$\_$D/)$\_$All/), 3) The effect of delamination aspect ratio (b/a) on the delamination shape factor (f$\_$s/) and the delamination growth rate (dA$\_$D// da). As results, it was known that the delamination aspect ratio (b/a) was decreased and the delamination area rate ((A$\_$D/)$\_$N// (A$\_$D/)$\_$All/) was increased as the normalized crack size (a/W) was increased. And, the delamination shape factors (f$\_$s/) of the ellipse-II(f$\_$s3/) was greater than of the ellipse-I(f$\_$s2/) but that of the triangle (f$\_$s1/) was less than of the ellipse-I(f$\_$s2/).

• 대한기계학회논문집B
• /
• 제30권6호
• /
• pp.505-513
• /
• 2006

The pressure drop characteristics in a rotating two-pass duct with rib turbulators are investigated in the present study. Three ducts of different aspect ratios (W/H=0.5, 1.0 and 2.0) are employed with a fixed hydraulic diameter ($D_h$) of 26.7 mm. $90^{\circ}$-rib turbulators with $1.5mm{\times}1.5mm$ cross-section are attached on the leading and trailing surfaces. The pitch-to-rib height ratio (p/e) is 1.0. The distance between the tip of the divider and the outer wall of the duct is 1.0 W. The thickness of divider wall is 6.0 mm o. 0.225 $D_h$. The Reynolds number (Re) based on the hydraulic diameter is kept constant at 10,000 and the .elation number (Ro) is varied from 0.0 to 0.2. As duct aspect ratio increases, high friction factor ratios show in overall regions. The reason is that the rib height-to-duct height ratio (e/H) increases, but the divider wall thickness-to-duct width ($t_d/W$) decreases. The rotation of duct produces pressure drop discrepancy between the leading and trailing surfaces. However, the pressure drop discrepancy of the high duct aspect ratio (AR=2.0) is smaller than that of the low duct aspect ratio (AR=0.5) due to the decrement of duct hight (H).

• 한국추진공학회지
• /
• 제20권2호
• /
• pp.94-101
• /
• 2016

본 논문에서는 날개의 가로세로비 변화가 날개 하부 유동장에 미치는 공기역학적 영향을 압력분포 측정과 입자영상속도계(PIV)를 이용하여 조사하였다. PIV 측정결과를 이용하여 파일런 주변 유동장의 속도변화를 레이놀즈수 $1.384{\times}10^5$ 와 $2.306{\times}10^5$의 조건에서 속도 성분별로 각각 분석하였다. 파일런으로부터 날개의 끝단이 시위 길이의 80% 만큼 떨어진 가로세로비 4.8의 경우, 날개 끝단으로부터의 끝단 와류의 영향이 날개 아랫면의 표면압력을 낮아지게 하고, 날개 끝단 주변의 흐름을 가속시킴으로써 날개 하부의 파일런 주변 유동장에 영향을 미쳤다. 시험결과에서는 가로세로비가 증가함에 따라 날개 하부 유동장에 대한 날개 끝단으로부터의 공기역학적 효과는 작아지는 경향을 보였다.

• 한국강구조학회 논문집
• /
• 제13권3호
• /
• pp.301-311
• /
• 2001

내풍설계에 있어서, 아스펙트비가 6정도인 초고층 건물의 각주형 단면의 바람에 의한 공력 불안정 진동 또는 갤로핑 진동이 발생할 수 있다. 본 연구에서는 등류에서 아스펙트비 6정도이고 변장비가 1/4간격으로 1에서 2까지의 초고층 건물의 각주형 단면에대한 공력불안정 진동과 갤로핑 진동에 대해 실험적으로 고찰하였다. 실험 결과, 등류시 코너 컷이 없는 경우가 코너 컷을 가진 초고층 건물의 각주형 단면에 비해 공력 불안정 진동이 커지는 경향이 있으며, 또한 갤로핑 진동도 나타났다. 따라서, 코너 컷에 의해 각주형 초고층 건물에서의 공력 불안정 진동은 효과적으로 저감되었다.

• 한국결정성장학회지
• /
• 제10권3호
• /
• pp.177-184
• /
• 2000

약한 cusp 자장이 가하여진 Czochralski실리콘 단결정 성장에서 유동장의 종횡비에 따라 부력과 열모세관 현상이 용융물질의 유동과 물질(산소)전달에 미치는 영향이 수치적인 방법으로 연구되었다. 실리콘 단결정 성장이 진행됨에 따라 도가니안의 용융물질의 깊이가 즐어들어 유동장의 종횡비가 감소하고, 이에 따라 현존하는 유동장에 작용하는 자장의 상대적인 형태가 변화하므로 유동의 형태가 계속 변화한다. 유동장 내부에서 자유표면으로 접근하여 Marangoni 대류를 구성하는 용융물질의 흐름(열모세관 현상)과 함께 도가니 벽 근처의 자유표면 바로 아래에서 순환류가 발생하는데, 이 순환류의 존재로 인하여 부력의 효과가 “전반적으로”나타나지 않고 도리어 “국소적으로”나타나는 특성을 갖는다. 종횡비가 작아질수록 유동장의 대부분에서 자장의 반경방향 성분이 축방향 성분보다 우세하여 용융물질의 유동은 횡방향 성분(수평성분)이 현저해지므로 자오면에서의 온도분포는 점차 반경방향에 의존하는 특성을 갖게 된다 종횡비가 작아질수록 결정의 가장자리에서 온도구배가 작아지며 따라서 열모세관 현상포 약화된다 또 이때 결정주위의 산소의 농도가 작아지며 따라서 흡수되는 산소의 양도 작아진다.

• 한국가시화정보학회지
• /
• 제19권3호
• /
• pp.99-105
• /
• 2021

In this study, the thermal stratification in solar seasonal thermal storage tanks was numerically simulated. The effects of the aspect ratio (AR) and inlet velocity on the thermal stratification in the diffuser type heat storage tank were investigated. The temperature distributions inside the tank were similar with velocity fields. Jet flows from opposite diffusers encountered each other at the tank center region. Thereafter, the downward flows occurred, and this flows strongly affected the thermal stratification. When AR was smaller than 2, these downward flows influenced a further distance and enhanced mixing inside the tank. Thermal stratification was evaluated by thermocline thickness and degree of stratification, and AR of 3 had the highest degree of stratification. The inlet velocity effect was expressed with the ratio (Re/Ri) of Reynolds and Richardson numbers. The second-order approximation was found for the relationship between the thermocline thickness and log Re/Ri.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권3호
• /
• pp.294-302
• /
• 1998

The charateristics of the convective mass transfer in horizontal rectangular enclosure with horizontal concentration gradients are analyzed. The effect of Grashof number(Gr) and aspect ratio(L/H) is investigated numerically using the control-volume method. Numerical results are obtained for Grashof numbers between $10^4$ and $10^6$ aspect ratios from 1 to 100 and results are compared with existing andlytical results. It is found that there exists a well defined aspect ratio for which the mean Sherwood number is maximum and the core flow changes from parallel to non-parallel at $Gr^2{Sc^2}(A^{-3}}{\geq}{10^5}$ and in the Ralongrightarrow0 regime the numerical results agreed very well with correlation derived from analytical results.

• 대한기계학회논문집B
• /
• 제28권7호
• /
• pp.842-849
• /
• 2004

The objective of this work is to study the improvement of etching characteristics in wet etching process. The etching characteristics such as etching factor were investigated under different etching conditions and compared with the spray characteristics. The spray characteristics of nozzle with different geometries such as swirler angle and swirl chamber aspect ratio were analyzed by using PDA system to predict the effect of the spray characteristics on the etching factor. The swirler angles were 49,5$^{\circ}$, 63$^{\circ}$ and 76.5$^{\circ}$. The swirl chamber aspect ratios were 1.2, 1.6 and 2.0. It was found that the etching factor was correlated with the spray characteristics and also the smaller swiller angle, the larger etching factor became.