• 한국재료학회지
• /
• 제14권1호
• /
• pp.28-34
• /
• 2004

IN 738LC, the major material for gas-turbine for power generation, was heat treated at $750^{\circ}C$, $850^{\circ}C$, $950^{\circ}C$ for 1000, 2000, and 4000 hrs and the microstructural evolution and mechanical properties were examined using optical microscope, XRD, SEM/EDS. The results showed ${\gamma}$', the main strengthening elements in this alloy, was about 300 nm in size and was about 56% by area fraction in as-cast samples. The area fraction of ${\gamma}$' peaked at 2000 hours at $750^{\circ}C$. The average diameter of the ${\gamma}$' which was about 300 nm at ascast specimen increased to about 1 $\mu\textrm{m}$ after heat treatment at $950^{\circ}C$ for 4000 hrs. Carbides were formed at dendrite, cell or grain boundaries which was ascribed to the segregation caused by solute redistribution during solidification. It was found that MC type carbides formed at low temperature, whereas carbides of $M_{23}$ /$C_{ 6}$/ type formed at higher temperature or at longer degradation. The hardness and impact energy decreased as the heat treatment temperature or time of retention increased, which was inaccrodance with the area fraction of ${\gamma}$'.

• 한국화재소방학회논문지
• /
• 제18권4호
• /
• pp.64-71
• /
• 2004

본 논문에서는 NIST에서 개발한 CFAST 화재 모델링 코드를 사용하여 원자력발전소 펌프실 화재를 모의하였다. 급기 제한, 최소 산소 농도(Lower Oxygen Limit), 복사열 방출비율(Radiative Fraction), 방화문 개방 정도 등의 CFAST 입력 변수 변화에 따라 화재 성장 변화를 분석하였다. 분석 결과에 의하면 본 화재구역에서의 화재는 환기 지배형 화재이므로 급기 제한 및 최소 산소 농도 10%로 설정하는 것이 타당한 것으로 판단되며, 복사열 방출에 따라 상부층 가스 온도는 큰 변화가 없는 것을 알 수 있었다. 화재가 발생한 화재구역 내 펌프를 제외하고는 상부에 위치한 케이블은 모두 건전성을 유지하는 것으로 나타났으며, CCDP(Conditional CDP)를 평가한 결과 9.25E-07로, 화재위험도분석보다 현실적이고 불확실성이 감소한 결과를 도출할 수 있었다.

• Journal of Welding and Joining
• /
• 제33권1호
• /
• pp.61-71
• /
• 2015

The effect of welding condition on microstructure and mechanical property of Plasma-MIG Hybrid Weld between Al 5083 plates(thickness : 10mm) was investigated. 1 pass weld without any defects such as puckering, undercut, and lack of fusion was obtained by 150~200A of plasma current and 5~7mm of welding speed. Gas porosities and shrinkage porosities were existed in the weld near fusion line. As welding speed and plasma current were decreasing, the area fraction of porosity was increasing. The hardness of the weld is increasing as welding speed. On the basis of microstructural analysis, Mg segregated region near dendrite boundaries tends to increase with the welding speed. In the result of hardness test, Distribution of hardness in fusion zone showed little change with the plasma current. However, when the welding speed increased, hardness in weld metal markdly increased. It could be considered that effect of heat input to growth of the dendritic solidification structures. Based on tensile test, tensile properties of weld metal was predominated by area fraction of porosities. Consequently, tensile properties can be controlled by formation site and area fraction of porosity.

• 대한금속재료학회지
• /
• 제48권7호
• /
• pp.589-597
• /
• 2010

In the present study, the effect of variation in alloying elements on the carbide formation behavior during casting and homogenization treatment of M2 high speed steels was investigated. M2 high speed steels of various compositions were produced by vacuum induction melting. Contents of C, Cr, W, Mo, and V were varied from the basic composition of 0.8C, 0.3Si, 0.2Mn, 4.0Cr, 6.0W, 5.0Mo, and 2.0V in weight percent. Homogenization treatment at $1150^{\circ}C$ for 1.5 hr followed by furnace cooling was performed on the ingots. Area fraction and chemical compositions of eutectic carbide in as-cast and homogenized ingots were analyzed. Area fraction of eutectic carbide appeared to be higher in the ingots with higher contents of alloying elements the area fraction of eutectic carbide also appeared to be higher on the surface regions than in the center regions of ingots. As a result of the homogenization treatment, $M_2C$ carbide, which was the primary eutectic carbide in the as-cast ingots, decomposed into thermodynamically stable carbides, MC and $M_6C$. The latter carbide was found to be the main one after homogenization. Fine carbides uniformly distributed in the matrix was found to be MC type carbide and coarsened by homogenization.

• Journal of Periodontal and Implant Science
• /
• 제49권1호
• /
• pp.25-38
• /
• 2019

Purpose: This study evaluated differences in bone healing and remodeling among 3 implants with different surfaces: sandblasting and large-grit acid etching (SLA; IS-III $Active^{(R)}$), SLA with hydroxyapatite nanocoating (IS-III $Bioactive^{(R)}$), and SLA stored in sodium chloride solution ($SLActive^{(R)}$). Methods: The mandibular second, third, and fourth premolars of 9 dogs were extracted. After 4 weeks, 9 dogs with edentulous alveolar ridges underwent surgical placement of 3 implants bilaterally and were allowed to heal for 2, 4, or 12 weeks. Histologic and histomorphometric analyses were performed on 54 stained slides based on the following parameters: vertical marginal bone loss at the buccal and lingual aspects of the implant (b-MBL and l-MBL, respectively), mineralized bone-to-implant contact (mBIC), osteoid-to-implant contact (OIC), total bone-to-implant contact (tBIC), mineralized bone area fraction occupied (mBAFO), osteoid area fraction occupied (OAFO), and total bone area fraction occupied (tBAFO) in the threads of the region of interest. Two-way analysis of variance (3 types of implant $surface{\times}3$ healing time periods) and additional analyses for simple effects were performed. Results: Statistically significant differences were observed across the implant surfaces for OIC, mBIC, tBIC, OAFO, and tBAFO. Statistically significant differences were observed over time for l-MBL, mBIC, tBIC, mBAFO, and tBAFO. In addition, an interaction effect between the implant surface and the healing time period was observed for mBIC, tBIC, and mBAFO. Conclusions: Our results suggest that implant surface wettability facilitates bone healing dynamics, which could be attributed to the improvement of early osseointegration. In addition, osteoblasts might become more activated with the use of HA-coated surface implants than with hydrophobic surface implants in the remodeling phase.

• Journal of Welding and Joining
• /
• 제13권1호
• /
• pp.103-114
• /
• 1995

Plasma Transferred arc(PTA) hard facing process has been developed to obtain an overlay weld metal having excellent wear resistance. The effect of Ti, TiSi$_{2}$ and TiC powders addition on the surface of Aluminum alloy 5083 has been investigated with PTA process. This paper describes the result of test the performance of the overlay weld metal. The result can be summarized as follows 1. Intermetallic compound is formed on surface of base metal in Ti or TiSi$_{2}$ powder but the reaction with surface of base metal is little seen in TiC powder. 2. In formation of composite layer on aluminum alloy surface by plasma transferred arc welding process, high melting ceramics like TiC powder is excellent. 3. The multipass welding process is available for formation of high density of powder. But the more number of pass, the less effect of powder, it is considered, and limits of number of pass. 4. By increasing area fraction of TiC powder on Al alloy surface, in especially TiC powder the hardness increase more than 40% area fraction and 88% shows about Hv 700.

• 한국대기환경학회지
• /
• 제12권3호
• /
• pp.269-278
• /
• 1996

Airborne suspended particulates were collected by an Andersen high volume air sampler in a traffic area of Seoul from September 1990 to August 1991. Origanic matter extracted from particulates, their fractions, namely acidic, basic, neutral and carcinogenic subfractions (PAHs, nitroarenes) in neutral fractions were assayed for mutagenicity on TA98, TA100 and TA98NR deficient Salmonella strains, use of the pre-incubation method. The relative contribution to total mutanenicity of organic matters was highest in neutral fraction and was lowest in basic fraction. Among subfractions, that of neutral fraction was higher nitroarenes subfraction compared to PAHs subfraction. While the carcinogenic effect of benzo[a]pyrene was calculated as 0.96 persons/million persons based on unit risk estimates by extrapolation method, life time excess cancer risk estimate of EOM, neutral, PAH fraction based on their mutagenicity was calculated as 52, 42, 3.8 persons/million persons, respectively. These findings indicate that the mutagenic hazard of the partciculate, air organic complex mixture, may be dependent upon the mutagen composition in the particulate and interactions each of them. Therfore, health risk from air organic complex mixtures based on mutagenicity might be useful indicator for evaluation of actual risk.

• 대한기계학회논문집B
• /
• 제20권1호
• /
• pp.384-398
• /
• 1996

An improved multi-channel Impedance Void Meter (IVM) is developed to measure an area-averaged void fraction. It consists of a main sensor, a reference sensor and a signal processor. The sensor was designed to be flush-mounted to the inner wall of the test section to avoid the flow disturbances. Guard electrodes are used to obtain evenly distributed electrical field in a measuring volume. A reference sensor is also installed to eliminate the drift in void signal caused by the changes in electrical properties of working fluid. The signal processor with three channels is specially designed so as to minimize the inherent error due to the phase difference between channels. As an example of applications, the mean and fluctuating components of void fraction are measured for bubbly and slug flow regime, and it is shown that IVM has good dynamic resolution which is required to investigate the structural developments of bubbly flow and the propagation of void waves in a flow channel.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제16권1호
• /
• pp.42-50
• /
• 2011

Potential risk of heavy metals to various receptors including humans depends on the bioavailability of the heavy metals in soil. In this study, the heavy metal extraction methods using 0.1N HCl and aqua regia were compared with the Tessier's sequential extraction method to assess whether these two methods can be used to determine the plant-available heavy metal concentrations. The contamination characteristics of copper (Cu), cadmium (Cd), lead (Pb), and arsenic (As) found in soils collected from 75 sites around the closed Janghang smelter were analyzed by extracting heavy metals using 0.1 N HCl, aqua regia, and the Tessier's sequential extraction method. The portion of metals bioavailable to plants is considered as the sum of the fraction 1 (exchangeable) and the fraction 2 (carbonates binding) of the Tessier's 5-step sequential extraction method, which were determined to be 3.1 ${\pm}$ 3.82, 0.6 ${\pm}$ 0.15, 20.6 ${\pm}$ 18.78, and 7.0 ${\pm}$ 6.48 mg/kg for Cu, Cd, Pb, and As, respectively, in this study. When the extraction using aqua regia and the Tessier's extraction method were compared, the extracted Cu and Pb concentrations did not show significant differences, whereas the extracted Cd and As concentrations showed significant differences. These results indicate that the portion of Cd and As in the fraction 5 of the Tessier's sequential extraction can not be extracted using aqua regia. Using aqua regia, which is the official test method, higher concentrations of Cu, Cd, Pb and As were extracted than the sum of the fraction 1 and 2. The results show that only 9, 40, 39 and 10% of Cu, Cd, Pb and As using aqua regia can be uptaken by plants (i.e., plant-available). Using 0.1N HCl, the portion of Cd equivalent to about 66% the fraction 1 could be extracted, while, with Pb, the portion of the fraction 1 and about 90% of the fraction 2 could be extracted. With As, the portion equivalent to the fraction 1, 2 and 79% of the fraction 3 was extracted, while with Cu, the portion equivalent to the fraction 1, 2, 3 and 20% of the fraction 4 was extracted using 0.1N HCl.

• 한국식품과학회지
• /
• 제49권3호
• /
• pp.331-337
• /
• 2017

배초향 추출물 및 분획별 생리활성 물질의 분포양상을 검정하기 위해 파이토케미컬 검색을 한 결과, 플라보노이드 확인시험에서 헥세인을 제외한 에틸아세테이트 및 부탄올 분획에서 양성반응을 확인하였다. 배초향 추출물의 극성에 따른 분획-헥세인, 에틸아세테이트 및 부탄올 분획의 산화방지 정도를 평가한 결과, 폴리페놀 함량, DPPH 라디칼 소거 및 환원력 실험에서 에틸아세테이트 분획이 다량의 폴리페놀을 함유하며 강력한 라디칼 소거 및 환원능력을 나타냈다. 또한 배초향 에틸아세테이트 분획의 항염 활성을 평가한 결과, 지방질다당류로 활성화된 BV-2 microglia에서 발생하는 과량의 산화질소(II) 생성을 억제하였을 뿐 아니라, 산화질소(II) 생성 효소인 iNOS 및 염증성 사이토카인 IL-6의 발현을 억제함을 확인하였다. 강력한 산화방지 및 항염증 활성을 나타내는 배초향 에틸아세테이트 분획내의 활성물질을 확인하고자 HPLC를 이용하여 분석한 결과, 배초향의 산화방지 물질로 잘 알려져 있는 로스마린산이 배초향 에틸아세테이트 분획에 함유되어 있음을 확인하였다.