• Journal of the Korean Magnetics Society
• /
• v.15 no.2
• /
• pp.130-132
• /
• 2005

Tungsten carbon nitride (W-C-N) thin films were produced by reactive radio frequency (RF) magnetron sputter-ing of tungsten in $Ar-N_2$ gas mixture. The effects of the variation of nitrogen partial pressure on the composition, and structural properties of these films as well as the influence of post-deposition annealing have been studied. When $La_{0.67}Sr_{0.33}MnO_3$ was coated on the W-C-N/Si substrate, coercivity ($H_c$) and magnetization at room temperature shows 58.73 Oe, and 29.4 emu/cc, respectively. In order to improve the diffusion barrier characteristics, we have studied the impurity behaviors to control the ratios of nitrogen and carbon concentrations.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.17 no.2
• /
• pp.155-160
• /
• 2011

In these days, there are increasing demands for weight reduction in many industrial fields including marine industries. Therefore, magnesium thin films for lightweight materials were prepared on magnesium alloy substrate. The influence of gas pressure and substrate bias voltages on the crystal orientation and morphology of the films was determined by using X-ray diffraction and FE-SEM, respectively. And the effect of crystal orientation and morphology of the magnesium thin films on corrosion behavior was estimated by measuring electro-chemical anodic polarization curves in deaerated 3% NaCl solution. From the results, corrosion resistance of Mg thin films was improved by controlling the crystal orientation and morphology of the films with effective use of plasma ion plating technique.

• Journal of the Korean Magnetics Society
• /
• v.11 no.5
• /
• pp.196-201
• /
• 2001

The dependence of CoFe interfacial layer thickness and plasma oxidation condition on tunneling magnetoresistance (TMR) in Ta/NiFe/FeMn/NiFe/Al$_2$O$_3$/NiFe/Ta tunnel junctions was investigated. As the CoFe layer thickness increases, TMR ratio rapidly increases to 13.7 % and decreases with further increase of the CoFe layer thickness. The increase of TMR with the CoFe thickness up to 25 was thought to be due mails to the high spin-polarization of CoFe. The maximum MR of 15.3% was obtained in the Si(100)/Ta(50 )/NiFe(60 )/FeMn(250 )/NiFe(70 )/Al$_2$O$_3$/NiFe(150 )/Ta(50 ) magnetic tunnel junction with a 16 Al oxidized for 40 sec using a Ar/O$_2$ (1:4) mixture gas.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.3
• /
• pp.146-151
• /
• 2004

Indium tin oxide (ITO) is widely used to make a transparent conducting film for various display devices and opto-electric devices. In this study, ITO films on glass substrate were fabricated by inductively coupled plasma (ICP) assisted dc magnetron sputtering. A two-turn rf coil was inserted in the process chamber between the substrate and magnetron for the generation of ICP. The substrates were not heated intentionally. Subsequent post-annealing treatment for as-deposited ITO films was not performed. Low-temperature deposition technique is required for ITO films to be used with heat sensitive plastic substrates, such as the polycarbonate and acrylic substrates used in LCD devices. The surface roughness of the ITO films is also an important feature in the application of OLEDs along with the use of a low temperature deposition technique. In order to obtain optimum ITO thin film properties at low temperature, the depositions were carried out at different condition in changing of Ar and $O_2$ gas mixtures, ICP power. The electrical, optical and structural properties of the deposited films were characterized by four-point probe, UV/VIS spectrophotometer, atomic force microscopy(AFM) and x-ray diffraction (XRD). The electrical resistivity of the films was -l0$^{-4}$ $\Omega$cm and the optical transmittance in the visible range was ＞85%. The surface roughness ( $R_{rms}$) was -20$\AA$.>.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.3
• /
• pp.939-942
• /
• 2011

Conductive carbon films were prepared at room temperature by unbalanced magnetron sputtering (UBMS) on silicon substrates using argon (Ar) gas, and the effects of post-annealing temperature on the structural, tribological, and electrical properties of carbon films were investigated. Films were annealed at temperatures ranging from $400^{\circ}C$ to $700^{\circ}C$ in increments of $100^{\circ}C$ using a rapid thermal annealing method by vacuum furnace in vacuum ambient. The increase of annealing temperature contributed to the increase of the ordering and formation of aromatic rings in the carbon film. Consequently, with increasing annealing temperature the tribological properties of sputtered carbon films are deteriorated while the resistivity of carbon films significantly decreased from $4.5{\times}10^{-3}$ to $1.0{\times}10^{-6}\;{\Omega}-cm$ and carrier concentration as well as mobility increased, respectively. This behavior can be explained by the increase of sp2 bonding fraction and ordering $sp^2$ clusters in the carbon networks caused by increasing annealing temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.367-367
• /
• 2008

Aluminum nitride (AlN) thin films have been deposited on Si substrate by using reactive RF magnetron sputtering method in a gas mixture of Ar and $N_2$ at different $N_2$ concentration. It was found that $N_2$ concentration was varied in the range up to 20-100%, highly c-axis oriented film can be obtained at 50% $N_2$ with full width at half maximum (FWHM) $4.5^{\circ}$. Decrease in surface roughness from 7.5 nm to 4.6 nm found to be associated with decrease in grain size, with $N_2$ concentration; however, the AlN film fabricated at 20% $N_2$ exhibited a granular type of structure with non-uniform grains. The absorption peak was observed around 675 $cm^{-1}$ in fourier transform infrared spectroscopy (FTIR). It is concluded that the AlN film deposited at $N_2$ concentration of 50% exhibited the most desirable properties for the application of high-frequency surface acoustic devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.425-425
• /
• 2008

The transparent conducting oxides(TCOs) are widely used as electrodes for most flat panel display devices(FPDs), electrodes in solar cells and organic light emitting diodes(OLED). Among them, indium oxide materials are mostly used due to its high electrical conductivity and a high transmittance in the visible spectrum. The present study reports on a study of the electrical and optical properties of IGZO thin films prepared on glass and PET substrates by the combinational magnetron sputtering. We use the targets of IZO and Ga2O3 for the deposition process. In some case the deposition process is coupled with the End-Hall ion-beam treatment onto the substrates before the sputtering. In addition we control the deposition rate to optimize the film quality and to minimize the surface roughness. Then we investigate the effects of the Ar gas pressure and RF power during the sputtering process upon the electrical, optical and morphological properties of thin films. The properties of prepared IGZO thin films have been analyzed by using the XRD, AFM, a-step, 4-point probe, and UV spectrophotometer.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1542-1545
• /
• 2009

For the application of flexible substrate to future display and new transparent devices, indium tin oxide (ITO) thin film was formed on polycarbonate(PC) substrate at room temperature by in-line sputter system. During the ITO sputtering, Ar and $O_2$ reaction gas were fixed at a constant value and the process pressure was varied from 3 to 7 mtorr. From the electrical and the optical properties of sputtered ITO films, the sheet resistances of as-deposited ITO films varied with a different pressure and the optical transmittances of the ITO films at visible wavelength were maintained above 85%. The results are considered to be due to the saturation of $O_2$ atoms from reaction in ITO film.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.8
• /
• pp.646-651
• /
• 1998

In this present study, the luminescence characteristics and mechanism of energy $CaTiO_3$:Pr phosphor were studied using disk specimens sintered at various temperatures and envirenment. A single-phase $CaTiO_3$:Pr was synthesized by sintering above 140$0^{\circ}C$ and its crystal structure was found to be perovskite orthorhombic. A dominant peak around 360 nm and a broad peak around 395 nm were observed in the PLE(Photoluminescence Excitation) spectrum of $CaTiO_3$:Pr with fixed emission wavelength at 612 nm, the decay time of 360 nm excitation was found to be longer than that of 395 nm excitation. From this result, it is assumed that the free carrier excited to 360 nm is transferred to 395 nm energy level. Therefore, the decrease in 395 nm intensity observed in CaTiO$_3$:Pr specimens sintered in Ar gas environment induced shorter decay time and improved CL luminescence.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.4
• /
• pp.73-80
• /
• 1989

The image sensitive PbO photoconductive films were fabricated ar several deposition conditions such as $O_2$ gas pressure, deposition rate, and substrate temperature. And the effects of these deposition condition on the structural and electrical properties of them were investigated with the aid of scanning electron photomicrographs. X-ray diffraction patterns, and current-valtage chatacteristics. The results show that when PbO film has red tetragonal structure and its dominant orientations are <110> and <010> direction, photocurrent-darkcurrent ratio and light transfer ratio are increase.